CiNii Articles - Real cutting length

1

A convenient resectoscope model for self-training

TAJIMA Kimihisa , OKUDA Akiko , FUKUDA Shin , ORISAKA Makoto , SHIMADA Hayato , KOTSUJI Fumikazu

… Aim: To develop an effective self-training tool for operative hysteroscopy.<BR>Methods: A resectoscope model of convenient size (20cm in length) was developed for self-training of operative hysteroscopy. … The model consists of a wooden body, a plastic sheath, an elastic spring system, and a metal cutting loop. …

JAPANESE JOURNAL OF GYNECOLOGIC AND OBSTETRIC ENDOSCOPY 24(2), 291-295, 2008-12-01

J-STAGE Ichushi Web CrossRef References (8)
2

C22 Development of System to Estimate Tool Wear of Ball End Mill [in Japanese]

SONG Cheolwon , AOYAMA Hideki

… Cutting phenomenon of ball end mffling is complicated and the cutting point on the cutting edge depends on the normal direction of the points to be cut so that it is extremely difficult to estimate tool wear of ball end mffling. …

The ... Manufacturing & Machine Tool Conference 2008(7), 187-188, 2008-11-21

CiNii Fulltext PDF - Subscription
3

Basic Study on Feasibility for Position Surveying of the Underground Pipes by In-Pipe Surveyor Using Rotary Encoders [in Japanese]

HAMANO Toshiaki , ONO Manabu , KATO Shigeo

… Then, we are required to grasp its real buried position before digging at the construction or the maintenance in order to prevent from the cutting of the optical fiber cable. … Output of the rotary encoder contacting the wall shows the length of the wall. …

Journal of the Japan Society of Precision Engineering 73(6), 641-647, 2007-06-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (14)
4

An improvement of sorting efficiency in a ship-building stockyard [in Japanese]

KIMURA Hajime , NAKAO Youichi , KAJIWARA Hiroyuki

… In this paper, the logistics in the ship-building yard has two stockyards: One is for sorting by cutting date, and the other is for sorting subblocks to assemble. … The cost is simply defined by sum of the block-length in the sequence of the plates arriving at (or leaving) the stockyard, and it is independent of the stockyard capacity. … We show analysis of the block-length and the cost function. … We apply our approach to a real ship-building stockyard. …

西部造船会会報 (109), 185-193, 2005-03-20

CiNii Fulltext PDF - Open Access References (3) Cited by (1)
5

A Rapid Scheduling Method by Analysis of Effective flaw Avoidance for a Two-Dimensional Orthogonal Guillotine Cutting Stock Problem for Flawed and Connectable Resources [in Japanese]

SHONO Yuji , IKKAI Yoshitomo , KOMODA Norihisa

… A cutting stock problem against flawed and connectable resource is a kind of a constrained two-dimensional orthogonal guillotine cutting stock problem where orders are assigned to resources. … A resource is cut by "sets" which is combinations of fixed cutting blade for length direction, and cut end to end for width direction. … The effective degree means a rate of improvement of an extraction rate per length of an assigned target order. …

IEEJ Transactions on Electronics, Information and Systems 125(3), 496-501, 2005-03-01

J-STAGE CrossRef References (7) Cited by (1)
6

High Speed Endmilling of Ti-6Al-4V Alloy [in Japanese]

SEKIYA Katsuhiko , YAMANE Yasuo , NARUTAKI Norihiko

… Cutting temperature was measured by the tool-work thermocouple method, and the wear of the tool against the real cutting length was evaluated. … The temperature increased in power law of cutting speed, feed, and radial depeth of cut as can be observed in turning. …

Journal of the Japan Society for Precision Engineering. Supplement. Contributed papers 70(3), 438-442, 2004-03-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (14) Cited by (3)
7

Design of a Three-Dimensional Cut-Away Tool for the Turning of High Manganese Steels [in Japanese]

KITAGAWA Takeaki , KUBO Akihiko , MAEKAWA Katsuhiro

… Both the chip contact length on the rake face and the chip flow direction can be uniquely determined by the energy method when the restricted length is assumed to be proportional to the real uncut chip thickness in the direction of chip flow. … The optimum contact length is found to be 1.25 times as large as the real feed, which is slightly wider than that in the two-dimensional machining. …

Journal of the Japan Society of Precision Engineering 60(9), 1284-1288, 1994-09-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef
8

Fundamental Study on From Grinding (2nd Report) : Grinding Process of V-Profile Groove [in Japanese]

NAKAJIMA Toshikatsu , UNO Yoshiyuki , YOSHINOBU Hidetoshi , YASUHARA Shinji

… Grinding process of V-profile groove with a formed wheel is experimentally investigated, analyzing initial profile of formed wheel, wheel wear, stock removal, number of cutting edges on working wheel surface, bonding strength of a cutting edge and so on. … (2) The number of cutting edges increases with increasing depth from wheel surface, increasing distance from the center of wheel width and larger formed angle of wheel. …

Journal of the Japan Society of Precision Engineering 54(5), 934-939, 1988-05-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef
9

The Analysis and Verification of Tree Volume Equations of Pinus elliottii in the State Forest of Aguas de Santa Barbara, Sao Paulo

Chyo Masamichi , Shiibayashi Toshiaki , Aoki Hideyo , Haga Nobor

… The cutting cycle for these pine stands was planned to be 25 or 30 years, so that the cutting time will come soon. … However, the volume and yield tables which are the necessary tools for the cutting planning, has not been prepared yet. … Further, these are classified into the equations for total volume, for commercial volume and for real commercial volume. …

Journal of the Faculty of Agriculture, Kyushu University 32(1/2), 95-109, 1987-12-00

IR
10

Cutting Mechanism of Sialon with a Single Point Diamond [in Japanese]

NAKAJIMA Toshikatsu , UNO Yoshikatsu , FUJIWARA Takanori , IKEJIRI Atsunori

… The circular cutting with a single point diamond cutting edge, in which the depth of cut is very small and takes maximum at some point, is carried out for making clear a cutting process of sialon under conditions similar to practical grinding, investigating sliding of a diamond on sialon, chip formation, groove profile, stock removal and so on. … elastic, plastic and cutting region. …

Journal of the Japan Society of Precision Engineering 53(8), 1271-1276, 1987-08-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef
11

Embrittlement Action of Free-machining Additives (2nd Report) : Estimation of Stress-strain Curve of Resulfurized Steel Based on MnS Particles' Action and Its Free-machining Effects [in Japanese]

OBIKAWA Toshiyuki , SHIRAKASHI Takahiro , USUI Eiji

… This consists of determination of stress-strain curve of resulfurized steel based on the behaviour around particles and evalua-tion of free-machining effects by FEM cutting simulations of both of resulfurized and plain carbon steels according to the stress-strain curves obtained above. …

Journal of the Japan Society of Precision Engineering 53(7), 1057-1063, 1987-07-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef
12

Study of Traverse Grinding Process (2nd Report) : Wheel Wear in Traverse Grinding [in Japanese]

OKAMURA Kenjiro , TSUKAMOTO Shinya , TAKEYAMA Ichiro

トラバース研削における各ステップの砥石摩耗は、砥石作用面のかつぎ現象と寸法生成機構に密接な関係を有する。本報告では、トラバース研削における砥石摩耗の変化過程を解明するために、研削距離を広範囲に変化させた研削実験を行った。主な結論は次のとおりである。(1)砥石作用面における各ステップの砥石摩耗量d_0(n)は、第1ステップで最大値をとり、後方のステップへ行くに従って階段状に減少する。(2)各ステップ …

Journal of the Japan Society of Precision Engineering 46(6), 753-758, 1980-06-05

CiNii Fulltext PDF - Subscription Cited by (2)
13

A Comment on Modern Kendo (3) : Centering Round Method of Guidance(ESSAYS COMMEMORATING THE RETIREMENT OF PROFESSOR KINICHI ASANO) [in Japanese]

Kaneko Kunikichi

浅野均一教授定年退職記念特集号

体育研究所紀要 11(1), 49-60, 1972-02-00

CiNii Fulltext PDF - Open Access IR
14

Studies on the Cryptocephalus approximatus Baly (Col. Chrysomelidae) [I] : Notes on the life-history and habits [in Japanese]

NAGATOMI AKIRA

(1)年1回の発生で, 成虫は福岡及び鹿児島の平地に於ては4∿6月にわたつて出現し, クリ, バラ等を食し, 卵を母虫の糞で包被して地上に落下させる.16∿36日を経て孵化した幼虫は糞殼を拡張して成長し, 4回程脱皮を行い, 年内に老熟して幼虫体で越多し, 3∿4月に糞殼の口を閉鎖して蛹化する.(2)糞殼拡張の機構は自己の排泄物を糞殼の開口部にとりつけることによつて長さを増 …

Japanese journal of entomology 20(1・2), 6-10, 1953-10-25

CiNii Fulltext PDF - Open Access

Search Results:　 1-14 of 14

Related Authors

Related Journals

Search Results: 1-14 of 14

Related Authors

Related Journals

Search Results:　 1-14 of 14