CiNii Articles - Tee-Joint

1

2007S-G4-29 Behavior of long brittle crack arrest in Tee joint structure of thick plate [in Japanese]

Handa Tsunehisa , Suzuki Shinichi , Toyoda Masanobu , Yokura Takahito , Kiji Noboru , Nakanishi Yasumasa

Conference proceedings, the Japan Society of Naval Architects and Ocean Engineers (4), 461-462, 2007-05

CiNii Fulltext PDF - Subscription Cited by (1)
2

2007S-G4-28 Effect of Kca value on behavior of brittle crack arrest in Tee joint structure of thick plate [in Japanese]

Handa Tsunehisa , Kubo Takahiro , Kawabata Fumimaru , Nishimura Kimihiro , Suzuki Shinichi , Shiomi Hiroshi , Miyata Takashi

Conference proceedings, the Japan Society of Naval Architects and Ocean Engineers (4), 459-460, 2007-05

CiNii Fulltext PDF - Subscription Cited by (1)
3

Effect of Gap and Characteristics on Seam Welding by Applying Magnetic Pressure [in Japanese]

OKAGAWA Keigo , AIZAWA Tomokatsu

塑性と加工 = JOURNAL OF THE JAPAN SOCIETY FOR TECHNOLOGY OF PLASTICITY 48(555), 323-327, 2007-04-25

References (11) Cited by (7)
4

Fatigue Strength Improvement of Fillet Welded Tee Joint by Low Transmation Temperature Welding Wire : Case of SUS304 Stainless Steel [in Japanese]

OHTA Akihiko , SUZUKi Naoyuki , MAEDA Yoshio

Pre-Prints of the National Meeting of JWS (69), 480-481, 2001-09-10

CiNii Fulltext PDF - Open Access References (3)
5

Statistical Property of Welding Deformation in Fillet Welding Tee Joint Flange : Statistical Treatment of Welding Deformation (Report 1) [in Japanese]

KAGAWA Kiyokazu , NAKAGARA Kiyoyuki , YAMAMOTO Koji , AKAZAWA Nobuki , SUITA Yoshikazu , OKADA Kenji , NANJO Tsutomu

… However, the welding deformation is expected to depend on welding operators because it is affected by the welding conditions such as welding heat input, leg length, and the restraint of weld joint. …

quarterly journal of the Japan Welding Society 17(1), 86-93, 1999-02-05

CiNii Fulltext PDF - Open Access References (2) Cited by (2)
6

Fatigue strength of tubular joints : Influence of weld residual stress on fatigue strength of as welded T-and X-joints [in Japanese]

Matsuoka Kazuyoshi , Chiaki Sadayoshi , Fujii Eisuke

… The purpose of this paper is to make clear the weld residual stress at toe of tubular T-and/or X-joint. … It is pointted out that the residual stress perpendicular to the weld line at the toe of tubular T-joint is very similar to that of fillet welded tee joint. …

Journal of the Society of Naval Architects of Japan (170), 683-692, 1991-12

CiNii Fulltext PDF - Subscription Journal@rchive CrossRef Cited by (3)
7

Fastening Characteristics of the Tee-Joint with Sheared Tab and Slot [in Japanese]

KAWAMURA Chuii

… the fastening of tee-joint with sheared tab and slot is carried out for different snaps. … The staking modes of the joint unions at different press-fitting force are obtained, and results are discussed by using pull-apart force and appearance of the joint. …

Transactions of the Japan Society of Mechanical Engineers. C 54(507), 2760-2764, 1988-11-25

CiNii Fulltext PDF - Open Access
8

Joining of Plain Carbon Steel to Alumina with Copper Filler Metal [in Japanese]

NAKA Masaaki , OKAMOTO Ikuo

… The use of this joining provides various type of joints such as alumina/steel tee joint and alumina butt joint strapped with steel. …

quarterly journal of the Japan Welding Society 3(4), 28-37, 1985-11-05

CiNii Fulltext PDF - Open Access
9

Improving the Fatigue Strength of Fillet Welded Joints by Toe Grinding and Wire Peening (Report 2) [in Japanese]

Ohta Shozaburo , Kudo Shoichi

… Various mechanical methods of improving the fatigue strength were investigated by testing the base plate and cruciform fillet welded joint specimens of 40kg/(mm)^2-80kg/(mm)^2 class steels. …

Journal of the Japan Welding Society 50(3), 270-277, 1981-03-05

CiNii Fulltext PDF - Open Access Cited by (1)
10

Deformation and Fracture of Welded Tee-Joint in Cylindrical Storage Tank [in Japanese]

Soya Isao , Minami Kenichi , Sato Mitsuo

… In this study, the model of Tee-joint which simulates the joint of cylindrical shell plate and annular bottom plate was examined and analyzed t research the deformation behavior of the joint and to investigate the criteria for design, welding and maintenance. …

Journal of the Society of Naval Architects of Japan (143), 264-274, 1978-06

CiNii Fulltext PDF - Subscription Journal@rchive CrossRef
11

Fatigue Strength of Fillet Welded Joints in 80kg/(mm)^2 High Strength Steel (Report 1) : Fatigue Strength of Plate with Transverse Fillet Welded Attachments [in Japanese]

Ohta Shozaburo , Eguchi Yasuhei

… The 2×(10)^6 cycles fatigue strength of plates with transverse fillet welded attachment, if statistically treated assuming it to be independent of the leg length, will be 13.2kg/(mm)^2 (in terms of joint factor, β_j=3.33) and 11.6kg/(mm)^2 with non-failure probability of respectively 50% and 90%. … (3) The critical fillet size (h_<cr>) in a fillet welded tee-joint has been found to be 1.8<2h_<cr>/T<1.9; …

Journal of the Japan Welding Society 43(4), 349-358, 1974-04-25

CiNii Fulltext PDF - Open Access
12

Comparison of MIG and TIG Welding Processes of Aluminum Alloy [in Japanese]

Masumoto Isao , Shinoda Takeshi

… But TIG welding has slow deposition rate, which causes a wider softened zone, and may lead to insufficient mechanical properties of welded joint. … 1) Tensile strength and ductility of MIG butt- and double-tee joints, which were welded with lower heat input than TIG welding, were superior to those of TIG joints. …

Journal of the Japan Welding Society 40(7), 666-674, 1971-07-25

CiNii Fulltext PDF - Open Access
13

Method of Radiographic Examination for welded T Joint in a Flue and Smoke-Tube Type Boiler

NOHARA Ishimatsu

… If a shell or flue is welded to a tube plate by T(tee) joint, remarkable thermal stress will occur at the welded parts owing to the temperature difference between shell and flue. … Authors has also studied on the relationship between film exposure and thickness of welded part to keep sufficient penetrant performance through the whole length of welded length of welded T joint. …

Bulletin of JSME 14(73), 694-703, 1971-07

CiNii Fulltext PDF - Open Access Journal@rchive
14

Prediction of Fillet Weld Penetration (Report II) : Practical application of fundamental theory to deep fillet weld [in Japanese]

Hashimoto Keisuke

… (3) Utilities of the formulas are experimentally confirmed by submerged are welding of Tee-joints. … (4) The theory of both-sides penetration of Tee-joint welded simultaneously which was presented in the 1st report is also confirmed experimentally for the deep fillet welds by submerged are welding. …

Journal of the Japan Welding Society 38(8), 857-865, 1969-08-25

CiNii Fulltext PDF - Open Access
15

Prediction of Fillet Weld Penetration (Report 1) : Fundamental investigation and practical application to shallow penetration of fillet welds [in Japanese]

Hashimoto Keisuke

… equations and diagrams of welding penetration are obtained from idealised models of a moving point heat source, and practical application of the theoretical penetration is investigated to predict actual penetration of a fillet welding joint as follows : (1) Relationship between welding conditions represented by dimentionless function N and theoretical penetration represented by dimentionless function D is given by the following equations with common parameter ρ : [numerical formula] N-D diagram obtained from the two equations above is presented …

Journal of the Japan Welding Society 38(4), 399-409, 1969-04-25

CiNii Fulltext PDF - Open Access
16

Studies on Tee Joint of Gas Pipe by Thermit-Brazing Process [in Japanese]

Watanabe Takeharu

… The process is successfully applied in field to join Tee-branch of gas pipe to be laid underground. …

Journal of the Japan Welding Society 35(4), 363-374, 1966-04-25

CiNii Fulltext PDF - Open Access
17

Fine Wire Manual MIG Welding of Thin Gage Aluminum Alloys [in Japanese]

Sugiyama Yoshihiko

… The useful minimum sheet thicknesses by this torch are seemed to be 0.8mm in a butt joint and 1.6mm in a tee joint respectively. … The hardness survey for welds showed that the heat affected zones in MIG welds usually narrower than in TIG welds and consequently the joint effeciencies of undressed MIG welds were superior to those of TIG welds but without reinforcement they behaved adversely possibly due to a lot of fine porosities in weld metal made by this process. …

Journal of the Japan Welding Society 33(7), 524-532, 1964-07-25

CiNii Fulltext PDF - Open Access
18

Prediction of Angular Distortion Caused by One Pass Fillet Welding [in Japanese]

Kumose Tomisaburo , Yoshida Toshiro , Abe Takeshi , Onoue Hisahiro

… magnitude of free angular distortion caused by one pass fillet welding was measured and maximum value of angular distortion was found when flange thickness ranged between ten and twelve millimetres in a tee joint.From the viewpoint of ship welding application, the co-authors, through this reserch, obtained material to predict quantities of free angular distortion caused by one pass fillet welding done with AC arc welders under conditions most applicable to shipyard practice (plate thickness and leg length), and further, …

Journal of Zosen Kiokai (98), 113-122, 1956-02

CiNii Fulltext PDF - Subscription

Search Results:　 1-18 of 18

Related Authors

Related Journals

Search Results: 1-18 of 18

Related Authors

Related Journals

Search Results:　 1-18 of 18