CiNii Articles - Thermal Fatigue

1

Influence of Crystallographic Orientation on Fatigue Reliability of β-Sn and β-Sn Micro-Joint (Special Issue on Lead-Free and Advanced Interconnection Materials for Electronics (5))

Kariya Yoshiharu , Tajima Sho , Yamada Saori

Materials Transactions 53(12), 2067-2071, 2012-12-00
2

Early Failure Detection of Interconnection with Rapid Thermal Cycling in Photovoltaic Modules

Aoki Yuichi , Okamoto Manabu , Masuda Atsushi , Doi Takuya , Tanahashi Tadanori

… To accelerate the degradation with thermal fatigue in crystalline silicon photovoltaic modules, the modules were exposed to dry thermal stress with rapid thermal cycling, and module impedance was monitored in situ during this testing. … The spikelike increase in module impedance at a temperature-alteration point was observed in the early stage of this rapid thermal cycling. …

Jpn J Appl Phys 51(10), 10NF13-10NF13-4, 2012-10-25

The Japan Society of Applied Physics
3

Numerical modeling of thermal fatigue cracks from the viewpoint of eddy current testing [in Japanese]

遊佐訓孝 , 橋爪秀利 , VIRKKUNEN Iikka 他

保全学 11(3), 73-78, 2012-10-00
4

Influence of creep property change on thermal fatigue life of solder joint [in Japanese]

MATSUO Keiichiro , FUNABIKI Kihachiro , MATSUSHIMA Michiya , FUKUMOTO Shinji , FUJIMOTO Kozo

溶接学会全国大会講演概要 91, 92-93, 2012-09-03

References (1)
5

Experimental Study on Prevention of High Cycle Thermal Fatigue in a Comp Reactor Vessel of Advanced Sodium Cooled Reactor : Thermal Striping Phenomena at Bottom of Upper Internal Structure [in Japanese]

小林順 , 木村暢之 , 飛田昭他

JAEA-research 2012(14), 1-40,巻頭1-2, 2012-07-00
6

Thermal Fatigue Characteristics of Molding Die Applying Nitriding Treatment on Electrical Beam Irradiated Surface [in Japanese]

SANO Masaaki , HAGIHARA Yoshihito , TAKAO Kiyotoshi , ISHIGURO Teruo , SUZUKI Daisuke , SAKAMOTO Chiaki , OKADA Akira

電気加工技術 36(113), 7-12, 2012-06-13

References (5)
7

Thermomechanical Fatigue Performance of Lead-Free Chip Scale Package Assemblies with Fast Cure and Reworkable Capillary Flow Underfills

Shi Hongbin , Tian Cuihua , Ueda Toshitsugu

… The test results show that the two underfill materials reduce the thermomechanical fatigue performance of CSP assemblies. … indeed, the coefficient of thermal expansion (CTE) is also very critical to the thermomechanical fatigue performance, but its effects is not so obvious in this study owing to the similar CTEs of the underfills used. …

Jpn J Appl Phys 51(5), 05EE04-05EE04-8, 2012-05-25

The Japan Society of Applied Physics
8

726 Corrosion Fatigue of Shot-peened and Thermal sprayed Materials [in Japanese]

Kono Yuzo , Shinhara Yosiko , Kayamoto Toshiyuki , Takeuchi Satoshi , Kido Mitsuo

学術講演会講演論文集 61, 437-438, 2012-05-25

CiNii Fulltext PDF - Limited
9

609 Fatigue Strength of Zirconia Ceramics Coated Material Using Thermal Spraying [in Japanese]

NISHIKAWA Izuru , HORIMOTO Takayuki , KOBAYASHI Akira , WAKI Hiroyuki

学術講演会講演論文集 61, 153-154, 2012-05-25

CiNii Fulltext PDF - Limited
10

108 Evaluation of Adhesive Fatigue Strength of WC-Co Thermal Sprayed Coating by Torsion Pin-test Method [in Japanese]

KANEKO Kenji , HIGAKI Keitaro , HAYASHI Kouki

学術講演会講演論文集 61, 15-16, 2012-05-25

CiNii Fulltext PDF - Limited
11

Board-Level Solder Joint Reliability of Edge- and Corner-Bonded Lead-Free Chip Scale Package Assemblies Subjected to Thermal Cycling

Shi Hongbin , Tian Cuihua , Ueda Toshitsugu

… In this paper, we present the results of thermal cycling test for edge- and corner-bonded lead-free chip scale packages (CSPs), which was carried out on the basis of the IPC-9701 test standard. … The thermal cycling test results show that corner-bond adhesive has comparable solder joint reliability performance with CSP without adhesive, and is better than edge-bond adhesive, followed by CSPs with FCFU. …

Jpn J Appl Phys 51(4), 04DB08-04DB08-10, 2012-04-25

The Japan Society of Applied Physics
12

Effects of Low-Power Pulsed Laser Irradiation on Muscle Contraction of Frog Gastrocnemius [in Japanese]

KOMATSU Mitsuaki , MURATA Masato , KOGURE Shinichi

レーザー研究 40(4), 285-291, 2012-04-15

References (17)
13

Effects of Thermal Fatigue and Water Absorption on Mechanical Properties of Natural Fiber Reinforced Plastic [in Japanese]

崎山昌孝 , 加藤木秀章 , 竹村兼一

強化プラスチックス 58(2), 49-52, 2012-02-00
14

Trends in Silicon Nitride Substrate with High Thermal Conductivity for Power Module [in Japanese]

那波隆之

Ceramics Japan : Bulletin of the Ceramic Society of Japan 47(1), 38-41, 2012-01-00
15

Thermal Fatigue Characteristics of Copper Alloy for Rocket Engine Combustion Chamber [in Japanese]

柳翔吾 , 今井周平 , 川合伸明他

銅と銅合金 51(1), 66-70, 2012-00-00
16

Effect of Hydrogen Pre-Charging on Fatigue Life on Medium Carbon Steels of Different Purity [in Japanese]

Suzuki Go , Oishi Kohei , Kato Aina , Tokuno Kazushige , Tsuchida Yutaka

… Fatigue tests were conducted on two kinds of normalized S45C commercial steel bars that are of different purity. … Amount and state of hydrogen are determined by thermal desorption spectroscopy (TDS) after cathodic charging. …

Tetsu-to-Hagane 98(9), 497-502, 2012

J-STAGE CrossRef
17

Investigation of Temperature Fluctuations Caused by Steam-Water Two-Phase Flow in Pressurizer Spray Piping

MIYOSHI Koji , NAKAMURA Akira , TAKENAKA Nobuyuki , OUMAYA Toru

… Initiation of high cycle fatigue cracks is suspected to occur under such thermally stratified two phase flow conditions due to cyclic thermal stress fluctuations caused by oscillations of the water surface. … In order to clarify the flow and thermal conditions in the pressurizer spray pipe and assess their impact on the pipe structure, an experiment was conducted for a steam-water flow at a low flow rate using a mock-up pressurizer spray pipe. …

Journal of Power and Energy Systems 6(2), 197-209, 2012

J-STAGE CrossRef
18

Effects of Thermal Loading Conditions on the Mechanical Properties of S45C/Cu/Si3N4 Composites [in Japanese]

SETTSU Nobuhiro , TAKAHASHI Manabu , MATSUSHITA Masafumi , OGI Keiji , TSUTSUMI Mitsuyoshi

… The effects of thermal loading conditions on the mechanical properties of S45C/Cu/Si3N4 … Thermal loading tests were conducted on test samples under various heat conditions, after which the joint parts of the samples were observed with a focus on the Cu interlayers using an optical microscope. … The results showed that thermal loading of the S45C/Cu/Si3N4 …

Journal of the Society of Materials Science, Japan 61(3), 292-298, 2012

J-STAGE CrossRef
19

Evaluation of Fatigue Strength for Solder Joints on NSMD Pads in Electronic Packages

NAKA Yasuhiro , YAGUCHI Akihiro , TANIE Hisashi , KIMOTO Ryosuke , YAMAMOTO Kenichi

… Generally, the thermal-cycling life of a package with NSMD pads is longer than that of a package with solder-mask-defined (SMD) pads, which are usually used in packages. … Therefore, we conducted mechanical fatigue tests on the joints of NSMD pads. …

Journal of Solid Mechanics and Materials Engineering 6(5), 339-350, 2012

J-STAGE CrossRef
20

Fatigue properties of alloy 718 overlay-coated with a Co-based X40 alloy by the Micro Spark Coating

KAMMA Ryohta , SAKAGUCHI Motoki , OKAZAKI Masakazu , SHIMODA Yukihiro , UCHIYAMA Takehiko , OCHIAI Hiroyuki , WATANABE Mitsutoshi

… In this study, some metallurgical and mechanical properties of a MSC layer made of a Co-based wear resisting alloy (X40), and its influence on the high temperature fatigue properties of Ni-based superalloy, Alloy718, were investigated. …

Journal of Solid Mechanics and Materials Engineering 6(3), 227-240, 2012

J-STAGE CrossRef

Search Results:　 1-20 of 1359

Related Authors

Related Journals

Search Results: 1-20 of 1359

Related Authors

Related Journals

Search Results:　 1-20 of 1359