CiNii Articles - Touch-trigger probe

1

Measurement and Compensation of Error Motions of Five-axis Machine Tools [in Japanese]

茨木創一

精密工学会誌 78(9), 763-766, 2012-09-00
2

Calibration of location errors of rotary axes on five-axis machine tools by on-the-machine measurement using a touch-trigger probe

Ibaraki Soichi , Iritani Takeyuki , Matsushita Tetsuya

… This paper proposes a scheme to calibrate location errors of rotary axes by on-the-machine measurement of a test piece by using a contact-type touch-trigger probe installed on the machine's spindle. …

International Journal of Machine Tools and Manufacture 58, 44-53, 2012-07-00

IR CrossRef
3

Development of a System to Measure Micro Hole Form Accuracy Using an Optical Fiber Probe (2nd Report):—Evaluation of a Prototype of the Measuring System—

MURAKAMI Hiroshi , KATSUKI Akio , ONIKURA Hiromichi , SAJIMA Takao , KAWAGOISHI Norio , KONDO Eiji

… This paper presents a micro hole measuring system using an optical fiber probe. … The system is composed of a fiber probe, two floodlighting fibers and two double-light reception fibers in the X and Y directions. … The fiber probe has an optical fiber of 30μm in diameter with a ball of 50μm in diameter on the end. … The probe is deflected when it comes into contact with a hole surface, and this deflection is measured optically. …

Journal of the Japan Society for Precision Engineering 76(8), 950-954, 2010

J-STAGE CrossRef
4

D28 Development of a Measuring System for Micro Hole Accuracy Using an Optical Fiber Probe : Evaluation of Measurement Repeatability(Nano/micro measurement and intelligent instruments)

MURAKAMI Hiroshi , KATSUKI Akio , ONIKURA Hiromichi , SAJIMA Takao , KAWAGOISHI Norio , KONDO Eiji , HONDA Tomohiro

… This paper presents a micro hole measuring system using an optical fiber probe. … The probe is deflected when it comes into contact with a hole surface, and this deflection is measured optically. … The results clarify that the probe has a resolution of 15 nm and the repeatability error for 10 measurements of a roughness standard specimen is within ±0.1μm in touch trigger mode and ±0.03μm in scanning mode. …

Proceedings of International Conference on Leading Edge Manufacturing in 21st century : LEM21 2009(5), 763-768, 2009-12-01

CiNii Fulltext PDF - Subscription
5

A Calibration Method for Coordinate Measuring Machine using Parallel Mechanism : Calibration with Double Ball Bar and Touch Trigger Probe [in Japanese]

OIWA Takaaki , KATAOKA Yorihiro

… The CMM with a touch trigger probe measures the moving ball of the DBB, and calculates position errors of the ball using kinematic parameters. …

Journal of the Japan Society of Precision Engineering 69(2), 222-226, 2003-02-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (11) Cited by (9)
6

Kinematic Calibration for 6 DOF Parallel mechanism [in Japanese]

YOSHIDA Osamu , OIWA Takaaki , KONDO Hiroyuki

… Therefore, we investigated possibility of calibration with touch trigger probe. …

年次大会講演論文集 : JSME annual meeting 2002(5), 45-46, 2002-09-20

CiNii Fulltext PDF - Subscription IR
7

Development of a Resonance-Based Touch Probe Structured with 2 Parallel Cross-shaped Thin Leaf Springs [in Japanese]

MATSUOKA Hirohito , KASEI Shinji , HINOHARA Makoto

… In this study, a resonance based touch trigger probe that detects a contact with lower measuring force is developed. … The touch trigger probe is consisted of 2 parallel thin cross-shaped leaf springs and a piezoelectric actuator. …

Journal of the Japan Society of Precision Engineering 68(2), 269-273, 2002-02-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (10)
8

Coordinate Measuring Machine using Parallel Mechanism (4th Report) : Development of Trial Measuring Machine [in Japanese]

OIWA Takaaki , BABA Shuhei

… The CMM employs specially made spherical joints and revolutionary joints, precise linear scales built in three prismatic joints, a touch trigger probe and an octahedral truss frame. … Variations in the length of the prismatic joints driven by AC servo motors move the probe in three-dimensional space. … When the probe touches the measuring object, the probe coordinates are calculated from the scale values. …

Journal of the Japan Society of Precision Engineering 66(11), 1711-1715, 2000-11-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (5) Cited by (6)
9

Development of Pneumatic Ball Probe (2nd Report) : Evaluative Experiments of Flux Trigger Sensor Type Probe [in Japanese]

KUO Chih-Che , TAKAMASU Kiyoshi , HIRAKI Masahiko , FURUTANI Ryoshu , OZONO Shigeo

… In this paper, a novel touch trigger probe which has a totally different construction concept namely, a pneumatic ball probe has been developed. … This touch trigger type pneumatic ball probe consists of a small probe ball, a thin pipe, a pneumatic trigger sensor and a vacuum pump. …

Journal of the Japan Society of Precision Engineering 66(4), 612-616, 2000-04-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (5) Cited by (3)
10

309 A Study on Coordinate Measurement Error Cased by Touch-Trigger Probe [in Japanese]

QIU Hua , NAKANO Hidetoshi

日本機械学会九州支部講演論文集 2000(53), 63-64, 2000-03-13

CiNii Fulltext PDF - Subscription
11

Development of Piezo-element Sensor for Touch Trigger Probe [in Japanese]

ISHIKAWA Nobuhiro , HIDAKA Kazuhiko , NISHIMURA Kunitoshi

… A touch trigger probe sensor for coordinate measuring machines (CMM) detects a contact between a spherical stylus tip and an object to be measured. …

Journal of the Japan Society of Precision Engineering 66(2), 304-308, 2000-02-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (9)
12

Development of Reseat Mechanism in Touch Trigger Probe for CMM [in Japanese]

HIDAKA Kazuhiko , NISHIMURA Kunitoshi

… This paper presents a development of a reseat module which is included in a fast and accurate touch trigger probe for coordinate measuring machines (CMM). … In general, the reseat module absorbs contact force for safety and repositions the probe stylus. …

Journal of the Japan Society of Precision Engineering 66(2), 298-303, 2000-02-05

CiNii Fulltext PDF - Subscription J-STAGE CrossRef References (10) Cited by (1)
13

A Basic Analysis of Inspecting Cylindrical Gear Accuracy on Machine Tool with a Touch-Trigger Probe [in Japanese]

QIU Hua , HASHITANI Michiaki , NAKANO Hidetoshi , INUI Suiko , BOSAKA Junichi

… The measurement principle of the present method consists of four steps which include: (1) feeding a touch-trigger probe fixed on the grinding head to a suitable position relative to the measured gear set on the table of the grinding machine; … (2) rotating the table to contact the probe with the gear surface; …

Transactions of the Japan Society of Mechanical Engineers. C 65(631), 1148-1155, 1999-03-25

CiNii Fulltext PDF - Open Access References (10) Cited by (1)
14

A Study of the Accuracy of Touch-Trigger Probe [in Japanese]

Ohya Makoto

… A touch-trigger probe is widely used as a position-detecting device for coordinate measuring machines. … There are a few problems to be solved concerning the accuracy of the probe. … also, the detected position fluctuates corresponding to the contact speed and the moving direction of the probe. …

Transactions of the Japan Society of Mechanical Engineers. C 59(563), 2086-2091, 1993-07-25

CiNii Fulltext PDF - Open Access

Search Results:　 1-14 of 14

Related Authors

Related Journals

Search Results: 1-14 of 14

Related Authors

Related Journals

Search Results:　 1-14 of 14