Effect of Technological Factors on Strip Profile in Twin-roll Casting Process

この論文にアクセスする

この論文をさがす

著者

抄録

Scientific and technical progress is presently impossible without the application of a new generation of materials with unique properties. Fine-grained alloys, obtained by rapid solidification technique in twin-roll casting process, belong to this class of materials. The commercial success of the twin-roll casting technique depends on the quality of its cast products, first of all on the cross-sectional shape of the strip. Otherwise, an additional post treatment of the as-cast strip such as cold rolling can deteriorate the unique properties of the strip.<br> To gain a better understanding of the influence of technological parameters on the cross-sectional shape of the strip, a laboratory-size twin-roll casting process has been investigated both theoretically and experimentally. It was found that the geometry of the nozzle slot, the roll sleeve thickness, diameter and length of the roll and the pressure profile between the rolls may influence the cross-sectional shape of the strip. Increasing the nozzle slot length, the flow rate and the distance between the nozzle and the melt bath surface increases the probability of formation of the thickness non uniformity across the strip width. The design of the roll plays a major role in the formation of the cross-sectional shape of the strip: a convex profile is produced by bending of the rolls whilst a concave profile results from thermal expansion of the rolls, in the case of a thick, water-cooled sleeve. The shape of the pressure profile between the rolls depends on the ratio strip width to roll length. Optimisation of the sleeve thickness, diameter and length of the roll is one of the possible ways of improving the cross-sectional profile and the flatness of the as-cast-strip.

収録刊行物

  • ISIJ international

    ISIJ international 38(10), 1107-1113, 1998-10-15

    The Iron and Steel Institute of Japan

参考文献:  18件中 1-18件 を表示

  • <no title>

    MIROSHNICHENKO I. S.

    Ind. Lab. 25, 1463, 1959

    被引用文献1件

  • <no title>

    BESSEMER H.

    US Patent 49053, 1865

    被引用文献3件

  • <no title>

    MIYAKE S.

    ISIJ Int. 31, 689, 1991

    被引用文献6件

  • <no title>

    ZAPUSKALOV N. M.

    Russian Patent 1793607, 1992

    被引用文献1件

  • <no title>

    MIZOGUCHI T.

    ISIJ Int. 36, 417, 1996

    被引用文献4件

  • <no title>

    LEGRAND H.

    Steel Time 104, 1998

    被引用文献1件

  • <no title>

    BLAZEK K. E.

    Ironmaking Steelmaking 39, 1998

    被引用文献1件

  • <no title>

    SHIBUYA K.

    ISIJ Int. 31, 661, 1991

    被引用文献7件

  • <no title>

    KUSTER T.

    New Steel 68, 1996

    被引用文献1件

  • <no title>

    ZAPUSKALOV N. M.

    Int. J. Cast. Met. Res. 9, 153, 1996

    被引用文献1件

  • <no title>

    PEARSON W. K. J.

    J. INST. Met. 93, 169, 1964

    被引用文献1件

  • <no title>

    SHIBUYA K.

    Mater. Sci. Eng. 98, 25, 1988

    被引用文献2件

  • <no title>

    MOLOTILOV B. V.

    Steel USSR 21, 565, 1991

    被引用文献1件

  • <no title>

    BOZORTH R. M.

    Ferromagnetism 15-19, 620, 1951

    被引用文献2件

  • <no title>

    KOZUKA T.

    ISIJ Int. 29, 1022, 1989

    被引用文献1件

  • <no title>

    DUWEZ P.

    J. Appl. Phys. 31, 1136, 1960

    DOI 被引用文献6件

  • Thin Strip Casting of Ni Base Alloys by Twin Roll Process

    YUKUMOTO Masao , YAMANE Hiroshi

    ISIJ international 35(6), 778-783, 1995-06-15

    J-STAGE DOI 参考文献23件 被引用文献6件

  • <no title>

    MOLOTILOV B. V.

    Met. Sci. Heat Treat. 34, 556, 1992

    DOI 被引用文献1件

被引用文献:  4件中 1-4件 を表示

各種コード

ページトップへ