下顎骨横断断層撮影における断層面角度と顎骨の形態変化 Angles of the Objective Plane Influenced the Mandibular Shape on Cross-sectional Tomography

この論文にアクセスする

この論文をさがす

著者

    • 飯田 啓人 IIDA Hiroto
    • 愛知学院大学歯学部歯科放射線学講座 Department of Oral and Maxillofacial Radiology, School of Dentistry, Aichi-Gakuin University
    • 内藤 宗孝 NAITOH Munetaka
    • 愛知学院大学歯学部歯科放射線学講座 Department of Oral and Maxillofacial Radiology, School of Dentistry, Aichi-Gakuin University
    • 有地 栄一郎 ARIJI Eiichiro
    • 愛知学院大学歯学部歯科放射線学講座 Department of Oral and Maxillofacial Radiology, School of Dentistry, Aichi-Gakuin University

抄録

Presurgical imaging diagnosis is important to obtain a more accurate prediction of the outcome of implant treatment.<br/> Cross-sectional jaw images in the bucco-lingual direction can usually be obtained by computed tomography (CT), or conventional X-ray tomography. However, it is considered that the measurement accuracy of conventional tomograms is affected by the angle of the tomographic objective plane and the mandibular shape. This study was performed to clarify the change in mandibular shape by shifting the angles of tomographic objective planes.<br/> Cross-sectional tomographic images were obtained on the bilateral central incisor, first premolar, and first molar regions of 10 dried mandibles, using a panoramic machine with a tomographic function (AZ 3000 DLP, Asahi Roentgen Ind. Co., Japan). The angles of tomographic objective planes were shifted horizontally within a range of 20 degrees, at intervals of 5 degrees, from the tomographic objective plane which was automatically determined. We measured the width between the surface of the buccal and lingual cortical bone.<br/> The optimal tomographic objective plane was defined as the plane representing the thinnest buccolingual width.<br/> The results were as follows.<br/> The means of bucco-lingual widths in the optimal planes were 9.3 mm, 9.7 mm, and 11.2 mm, in the incisor, premolar, and molar regions, respectively. The angle from the optimal plane, which permitted magnification within 0.5 mm in bucco-lingual width, was from -12.3 degrees to11.4 degrees in the incisor region. In the molar region, it was from -12.1 degrees to9.8 degrees, while it could not be determined, because of the limit of the machine's movement, in the premolar region.<br/> In conclusion, the change in mandibular shape by shifting the angles of tomographic objective planes was clarified.<br/>

収録刊行物

  • 日本口腔インプラント学会誌 = Journal of Japanese Society of Oral Implantology

    日本口腔インプラント学会誌 = Journal of Japanese Society of Oral Implantology 14(3), 45-50, 2001-09-30

    公益社団法人 日本口腔インプラント学会

参考文献:  16件中 1-16件 を表示

被引用文献:  1件中 1-1件 を表示

各種コード

  • NII論文ID(NAID)
    10008136907
  • NII書誌ID(NCID)
    AN10072606
  • 本文言語コード
    JPN
  • 資料種別
    ART
  • ISSN
    09146695
  • データ提供元
    CJP書誌  CJP引用  J-STAGE 
ページトップへ