クラスプ義歯における支台歯と顎堤の荷重分散に関する実験的研究 : コーヌステレスコープ義歯との比較 A Study on the Load Distribution of the Abutment Teeth and Residual Ridges of a Removable Partial Denture with Cast Clasps : In Comparison with a Conical Crown Retained Denture

この論文にアクセスする

この論文をさがす

著者

    • 三浦 美文 MIURA Yoshifumi
    • 北海道大学歯学部歯科補綴学第一講座 Department of 1st Prosthetic Dentistry, Hokkaido University School of Dentistry
    • 齋藤 正恭 SAITO Masayasu
    • 北海道大学歯学部歯科補綴学第一講座 Department of 1st Prosthetic Dentistry, Hokkaido University School of Dentistry
    • 野谷 健治 NOTANI Kenji
    • 北海道大学歯学部歯科補綴学第一講座 Department of 1st Prosthetic Dentistry, Hokkaido University School of Dentistry
    • 相澤 隆 AIZAWA Takashi
    • 北海道大学歯学部歯科補綴学第一講座 Department of 1st Prosthetic Dentistry, Hokkaido University School of Dentistry
    • 松井 透 MATSUI Tohru
    • 北海道大学歯学部歯科補綴学第一講座 Department of 1st Prosthetic Dentistry, Hokkaido University School of Dentistry
    • 川崎 貴生 KAWASAKI Takao
    • 北海道大学歯学部歯科補綴学第一講座 Department of 1st Prosthetic Dentistry, Hokkaido University School of Dentistry

抄録

The purpose of this study was to investigate the effects of various retainer designs on the characteristics of stress distribution and vertical dislodgment of the denture base. A mandible simulation model of unilateral distal-extension missing teeth (three teeth from the second premolar to the second molar) was used in this study. A conical crown, Akers clasp, and double Akers clasp were used as retainers.<BR>The results were as follows:<BR>1. The conical crown retained denture produced significantly less stress distribution and vertical dislodgment of the denture base than the two clasp designs.<BR>2. The conical crown retained denture produced the most intense stress on the apical and distal surfaces of the most distal abutment, while the double Akers clasp design produced the least stress.<BR>3. The Akers clasp design produced less load distribution of the denture base and greater vertical stress of the abutment tooth than the double Akers clasp design.<BR>4. The bilateral denture design produced less load distribution of the denture base and greater vertical stress of the abutment tooth.<BR>5. On condition of the bilateral denture design including clasps with a proximal plate, stress and load distribution were similar to those of the conical crown retained denture.

収録刊行物

  • 日本補綴歯科學會雜誌 = The journal of the Japan Prosthodontic Society

    日本補綴歯科學會雜誌 = The journal of the Japan Prosthodontic Society 42(4), 597-604, 1998-08-10

    Japan Prosthodontic Society

参考文献:  37件中 1-37件 を表示

被引用文献:  9件中 1-9件 を表示

各種コード

  • NII論文ID(NAID)
    10008170324
  • NII書誌ID(NCID)
    AN00197911
  • 本文言語コード
    JPN
  • 資料種別
    ART
  • ISSN
    03895386
  • データ提供元
    CJP書誌  CJP引用  J-STAGE 
ページトップへ