Effects of Heat Treatment Conditions on the Mechanical Properties of Orthodontic Stainless Steel Wires

この論文にアクセスする

この論文をさがす

著者

抄録

The purpose of this study was to evaluate mechanical properties of the orthodontic wires according to heat treatment environments and cooling methods. Four types of wires were heat-treated in air, argon and vacuum at 500°C, for 6 min, and were then either cooled in the furnace or a water bath. Increases in microhardness, maximal strength, yield strength and Young’s modulus of the orthodontic wires after heat treatment were approximately 0.4–22.9%, 2.9–14.8%, 3.7–14.4% and 2.5–9.0%, respectively. This was considered to be because of mainly precipitation hardening and additionally subgrain formation by the heat treatment. Yield strength and microhardness of the heat-treated wires were also significantly dependent upon the cooling methods. The microhardness and yield strength of the water-cooled wires were lower than those of the furnace cooled wires. This was attributed to the precipitation degree of chromium carbides dependent on cooling rate. Heat treatment in an air oxidized the surface of the wires, and the mechanical properties and surface cleanness of the water-cooled wires were poorer than those of the furnace-cooled wires. Conclusively, orthodontic wires should be heat-treated in vacuum conditions or an inert gas environment after plastic deformation and should be cooled in a furnace in order to inhibit surface oxidation, maximize corrosion resistance and improve the mechanical properties.

収録刊行物

  • Materials transactions

    Materials transactions 43(12), 3072-3077, 2002-12-01

    公益社団法人 日本金属学会

参考文献:  18件中 1-18件 を表示

  • <no title>

    BRANTLEY W. A.

    Orthodontic Materials, 77-103, 2001

    被引用文献2件

  • <no title>

    YANG H. Y.

    New metallic materials, 245-246, 1995

    被引用文献1件

  • <no title>

    KIM Y. B.

    J. Korean Foundation for Gnatho-Orthodontic Res 2, 151-197, 1995

    被引用文献2件

  • <no title>

    FUNK A. C.

    Angle Orthod. 21, 129-138, 1951

    被引用文献1件

  • <no title>

    KOHL R. W.

    Angle Orthod. 24, 37-52, 1964

    被引用文献1件

  • <no title>

    HOWE G. L.

    Angle Orthod. 38, 244-249, 1968

    被引用文献1件

  • <no title>

    GARDINER J. H.

    Dent. Practit. 20, 65-76, 1969

    被引用文献1件

  • <no title>

    SKINNER E. W.

    Skinner's science of dental materials 261-270, 537-551, 1991

    被引用文献1件

  • <no title>

    THUROW R. C.

    Edgewise Orthodontics, 42-66, 1982

    被引用文献1件

  • <no title>

    HENSTEN-PETTERSEN A.

    Orthodontic Materials, 287-299, 2001

    被引用文献1件

  • <no title>

    CULLITY B. D.

    Elements of X-ray diffraction, 421-446, 1978

    被引用文献1件

  • <no title>

    NETER J.

    Applied linear statistical model, 779-791, 1996

    被引用文献1件

  • <no title>

    NETER J.

    Applied linear statistical model, 776-777, 1996

    被引用文献1件

  • <no title>

    OH K. T.

    J. Korea Res. Soc. for Dent. Mater. 27, 207-215, 2000

    被引用文献1件

  • <no title>

    LANE D. F.

    Angle Orthod. 50, 139-145, 1980

    被引用文献1件

  • <no title>

    NIKOLAI R. J.

    Bioengineering analysis of orthodontic mechanics 113-144, 233-269, 1985

    被引用文献1件

  • <no title>

    MARCOTTE M. R.

    J. Dent. Res. 52, 1171-1175, 1973

    被引用文献1件

  • <no title>

    BACKOFEN W. A.

    Am. J Orthod. 38, 755-765, 1952

    DOI 被引用文献1件

被引用文献:  1件中 1-1件 を表示

各種コード

  • NII論文ID(NAID)
    10012329064
  • NII書誌ID(NCID)
    AA1151294X
  • 本文言語コード
    ENG
  • 資料種別
    ART
  • ISSN
    13459678
  • NDL 記事登録ID
    6395219
  • NDL 雑誌分類
    ZP41(科学技術--金属工学・鉱山工学)
  • NDL 請求記号
    Z53-J286
  • データ提供元
    CJP書誌  CJP引用  NDL  J-STAGE 
ページトップへ