AZ91D合金における半溶融射出成形時の固相率と鋳造欠陥の関係 Relationship between volume fraction solid and casting defect on semi solid injection in AZ91D magnesium alloy

この論文にアクセスする

この論文をさがす

著者

抄録

  Semi solid forming testing machine which has the same system as a runner-less injection machine has been made on an experimental basis. Temperature control system has been established to obtain the homogeneous solid-liquid coexisted state in its injection cylinder. Rod specimens were cast into a permanent mold by this machine in the semi solid state. The effect of solid fraction on the microstructure and the casting defect has been investigated and the results obtained as follows: <br>  A shearing in the part of nozzle of injection cylinder is the most important to reveal thixotropic property of alloy slurry in semi solid forming process by injection machine. So it needs controlling of solid fraction to affect it. In order to decrease casting defect and hold homogeneous structure, solid fraction more over 50% is needed. But when the solid fraction increases to 60%, primary solid particles glow coarser, so the primary solid particle size control technique is required to suppress it. In the case of less than 50% of solid fraction, alloy liquid preferentially fills inside the permanent mold and alloy slurry continue to fill the mold after alloy liquid. Then large casting defect form at the boundary of both flows.

収録刊行物

  • 鋳造工学 = Journal of Japan Foundry Engineering Society

    鋳造工学 = Journal of Japan Foundry Engineering Society 78(4), 187-193, 2006-04-25

    Japan Foundry Engineering Society

参考文献:  11件中 1-11件 を表示

  • <no title>

    MATSUNO S.

    1996 Japan Die Casting Congress Transactions, 1996

    被引用文献1件

  • <no title>

    SHIBATA R.

    J. JFS 69, 885, 1997

    被引用文献1件

  • <no title>

    ADACHI M.

    1998 Japan Die Casting Congress transactions, 1998

    被引用文献1件

  • <no title>

    IDEGOMORI T.

    J. of ASTP 41, 1201, 2000

    被引用文献1件

  • <no title>

    初山圭司

    軽量金属セミソリッド加工技術, 2005

    被引用文献1件

  • <no title>

    TSUKEDA T.

    IMONO 67, 936, 1995

    被引用文献1件

  • <no title>

    http://www.aist.go.jp/aist_j/press_release/pr2004/pr20040325/pr20040325.html#g

    被引用文献1件

  • <no title>

    YAMADA F.

    Die & Mould Technology 19, 46, 2004

    被引用文献1件

  • <no title>

    MIWA K.

    Met. Technol. (Jpn.) 75, 49, 2005

    被引用文献1件

  • <no title>

    MIWA K.

    J. Jpn. Soc. Technol. Plast. 41, 1210, 2000

    被引用文献1件

  • <no title>

    MIWA K.

    J. JFS 77, 554, 2005

    被引用文献1件

被引用文献:  1件中 1-1件 を表示

各種コード

  • NII論文ID(NAID)
    10018133244
  • NII書誌ID(NCID)
    AN10514770
  • 本文言語コード
    JPN
  • 資料種別
    ART
  • ISSN
    13420429
  • NDL 記事登録ID
    7933220
  • NDL 雑誌分類
    ZP41(科学技術--金属工学・鉱山工学)
  • NDL 請求記号
    Z17-277
  • データ提供元
    CJP書誌  CJP引用  NDL  J-STAGE 
ページトップへ