Synthesis Method for the Modelling and Robust Control of Coating Weight at Galvanizing Process

この論文にアクセスする

この論文をさがす

著者

    • SHIN Ki-Tae
    • Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH)
    • PARK Hea-Doo
    • POSCO Technical Research Laboratory, Rolling Technology & Process Control Research Group
    • CHUNG Wan-Kyun
    • Department of Mechanical Engineering, Pohang University of Science and Technology (POSTECH)

抄録

In this paper, we propose a new practical synthesis model for coating weight control and robust design method of feedback controller in galvanizing process. Firstly, we propose a new model, which combines both long term and short term model. Long term model has a good accuracy to predict the next distance and pressure of air knife for wide range of target coating weight, because it has the functions of classification, averaging and learning based on real measured data. Short term model has variational form based on linear change of inputs and outputs and is used at all controls except preset control. Based on this model, we propose a set of practical controller and a robust design method of feedback controller so that it can attenuate quickly the errors caused by time-delay and modelling error. The proposed model with controller were applied to continuous galvanizing line (CGL) at Kwang Yang Steel Works and we obtained good experimental results on the deviation control of coating weight at top of coil and uniform coating weight on the surface of strip.

収録刊行物

  • ISIJ international

    ISIJ international 46(10), 1442-1451, 2006-10-15

    The Iron and Steel Institute of Japan

参考文献:  14件中 1-14件 を表示

  • <no title>

    BUTLER J. J.

    AISE Year Book, 1970

    被引用文献1件

  • <no title>

    THORTON J. A.

    Acta Metall., B 7, 607, 1976

    被引用文献1件

  • <no title>

    EDWARDS W. J.

    Automatica 12, 225, 1976

    被引用文献1件

  • <no title>

    FENOT C.

    IFAC Adapt. Systems in Control and Signal Proc. Control Engineering Practice 1(Issue 5), 779, 1993

    被引用文献1件

  • <no title>

    MARKWARD S. W.

    Iron Steel Eng., 1995

    被引用文献1件

  • <no title>

    LU Y.-Z.

    IEEE Trans. Neural Networks 8(6), 129, 1997

    被引用文献1件

  • <no title>

    LACANETTE D.

    ISIJ Int. 45(2), 214, 2005

    被引用文献1件

  • <no title>

    HAPHADE P.

    ISIJ Int. 45(2), 209, 2005

    被引用文献1件

  • <no title>

    MENDEL J. M.

    Lessons in Estimation Theory for Signal Processing, Communications, and Control, 1987

    被引用文献1件

  • An adaptive fuzzy modeling for continuous galvanizing line

    WATANABE T.

    Proc. of the 1997 IEEE Int. Conf. on Syst., Man, and Cybern. 1, 663-668, 1997

    被引用文献2件

  • <no title>

    CHEN D.

    Automatica 31(5), 715, 1995

    被引用文献1件

  • <no title>

    JACOBS O. L. R.

    Control Eng. Pract. 3(11), 1529, 1995

    被引用文献1件

  • <no title>

    YOO S. R.

    IEEE Trans. Cont. Syst. Technol. 7(1), 129, 1999

    被引用文献1件

  • <no title>

    CHAE H. K.

    J. RIST 15(4), 370, 2001

    DOI 被引用文献1件

各種コード

ページトップへ