木材のプラスッチク溶接に関する研究
書誌事項
- タイトル別名
-
- A Study on the Plastic Welding of Lumber
抄録
This welding method can be applied for bonding not only between lumber and lumber, or lumber and plastics, but also between lumber and ceramic such as bricks, etc., or lumber and graphite, and between many other non-metallic substances. In this welding, after the pretreatment of the surfaces to be welded has been performed, welding is effected by use of a filler rod and a torch just in a similar manner to hot jet welding of plastics. As the filler rod, plastics is used, and as the welding gas, the air is utilized. As to the size of the beveling form of the weld, it is preferable to apply the regular size for an ordinary weld, but in practical usage, unevenness in the bonding surfaces would scarcely be an obstruction. In a broad sense, the plastic welding may be classified under the category of welding, but in a narrow sense, in as much as this welding method is not accompanied by the melting of lumber, etc., it may not belong to the category of welding. Presuming that the welding rod is a solder, this method may come under the category of brazing, while its operation can hardly be called brazing because it is virtually a kind of welding. For this reason, the present method is tentatively called plastic welding.<BR>The mechanism of the plastic welding of lumber is considered as follows: Lumber is composed of cells. Since lumber is thus constituted with numerous cells having thick cell-walls, the vacuoles which are termed the lumens are formed between one cell and another. Now, in the pretreatment process, the pretreating agent is caused to penetrate sufficiently into the lumens, whereby an electrostatic bonding force, along with the mechanical anchor effect, is generated in relation to lumber, and thus hot jet welding is effected on the surfaces which have been pretreated. In this manner, by the pretreatment which involves the elimination of various stains, and the activation of the surface to be welded, the lumber surface becomes so much activated as to greatly facilitate the hot jet welding to be carried out. These effects may vary depending upon the condition of formation of lumens which are different in composition from one lumber origin to another. On the other hand, these effects differ in their specific adhesion in accordance with the classification of lumber.<BR>It may be concluded: 1) The beveling area is the larger the better. 2) The moisture content has been measured to be 11.0-13.0 in pine wood, 9.8-13.0 in cryptomeria wood, 10.0-12.5 in hinoki wood, and 10.0-30.0 in lauan wood, and 9.0-13.0 in plywood. This necessitates a consideration for promoting the filler effect of the primer against the lumens by pre-drying. The drying condition of 150°C for one hour seems to bring about a good effect. 3) The transition phenomenon of the welding strength due to temperature and atmosphere resembles that of the primer and the welding rod. The more the properties of the bulking agents of both primer and welding rod are brougth forth, the stronger the weld will be. 4) The lumens are present in the direction of trunk axis, while the effect of the bulking agent is stronger in the axial direction. 5) The fatigue strength also resembles that of the bulking, where the quality of a bond largely depends upon the quality of the bulking agent. 6) According to the microphotographic observation, the condition of impregnation of the primer and the welding rod is good, and it has been made clear that sufficient keying action is present. 7) A welding joint efficiency of higher than 60% may easily be expected. A new bonding method for lumber has been developed, and it is considered that the initial objective has been achieved for the present.
収録刊行物
-
- 溶接学会誌
-
溶接学会誌 37 (2), 158-165, 1968
一般社団法人 溶接学会
- Tweet
詳細情報 詳細情報について
-
- CRID
- 1390282681479552000
-
- NII論文ID
- 130003763040
-
- ISSN
- 18837204
- 00214787
-
- 本文言語コード
- ja
-
- データソース種別
-
- JaLC
- Crossref
- CiNii Articles
-
- 抄録ライセンスフラグ
- 使用不可