Studies on automatic control of wood routing using acoustic emission アコースティック・エミッション信号を利用したルータ切削の自動制御に関する研究
この論文にアクセスする
この論文をさがす
著者
書誌事項
- タイトル
-
Studies on automatic control of wood routing using acoustic emission
- タイトル別名
-
アコースティック・エミッション信号を利用したルータ切削の自動制御に関する研究
- 著者名
-
Cyra Grzegorz
- 著者別名
-
ツェラ グジェゴシュ
- 学位授与大学
-
鳥取大学
- 取得学位
-
博士 (農学)
- 学位授与番号
-
甲第129号
- 学位授与年月日
-
1997-09-26
注記・抄録
博士論文
目次
- TABLE OF CONTENTS / p3 (0005.jp2)
- LIST OF TABLES / p6 (0008.jp2)
- LIST OF FIGURES / p7 (0009.jp2)
- INTRODUCTION / p1 (0013.jp2)
- REVIEW OF THE LITERATURE / p4 (0016.jp2)
- PART I. THE EFFECTS OF WOOD FIBER DIRECTIONS ON ACOUSTIC EMISSION / p11 (0023.jp2)
- 1.1 Introduction / p11 (0023.jp2)
- 1.2 Effect of grain angle / p12 (0024.jp2)
- 1.2.1 Experimental procedure / p12 (0024.jp2)
- 1.2.2 Results and discussion / p17 (0029.jp2)
- 1.3 Effect of annual ring angle / p28 (0040.jp2)
- 1.3.1 Experimental procedure / p28 (0040.jp2)
- 1.3.2 Results and discussion / p32 (0044.jp2)
- 1.4 Effect of slope angle / p35 (0047.jp2)
- 1.4.1 Experimental procedure / p35 (0047.jp2)
- 1.4.2 Results and discussion / p38 (0050.jp2)
- 1.5 Conclusions / p44 (0056.jp2)
- PART II. THE EFFECT OF ROUTER TOOL WEAR ON ACOUSTIC EMISSION / p47 (0059.jp2)
- 2.1 Introduction / p47 (0059.jp2)
- 2.2 Experimental procedure / p49 (0061.jp2)
- 2.2.1 Cutting conditions / p49 (0061.jp2)
- 2.2.2 AE measurements / p50 (0062.jp2)
- 2.2.3 Cutting forces measurements / p53 (0065.jp2)
- 2.2.4 Surface roughness measurements / p53 (0065.jp2)
- 2.2.5 Routing process analysis / p53 (0065.jp2)
- 2.3 Results and discussion / p54 (0066.jp2)
- 2.3.1 The effects of grain orientation and tool wear on AE signal / p54 (0066.jp2)
- 2.3.2 The effects of grain orientation and tool wear on cutting forces / p60 (0072.jp2)
- 2.3.3 The effects of grain orientation and tool wear on surface roughness / p60 (0072.jp2)
- 2.3.4 The effect of feed rate / p61 (0073.jp2)
- 2.3.5 AE versus edge recession / p67 (0079.jp2)
- 2.3.6 AE versus surface roughness / p67 (0079.jp2)
- 2.4 Conclusions / p68 (0080.jp2)
- PART III. ON-LINE CONTROL OF ROUTER FEED SPEED USING ACOUSTIC EMISSION / p70 (0082.jp2)
- 3.1 Introduction / p70 (0082.jp2)
- 3.2 Experimental Procedure / p71 (0083.jp2)
- 3.2.1 Adaptive control system / p71 (0083.jp2)
- 3.2.2 Experiment conditions / p75 (0087.jp2)
- 3.3 Results and discussion / p79 (0091.jp2)
- 3.4 The effect of the adaptive controller / p87 (0099.jp2)
- 3.4.1 Cutting along straight path (constant grain angle) / p87 (0099.jp2)
- 3.4.2 Cutting along circular arc (various grain angles) / p92 (0104.jp2)
- 3.5 Conclusions / p98 (0110.jp2)
- PART IV. SUMMARY AND CONCLUSION / p100 (0112.jp2)
- Summary / p100 (0112.jp2)
- Conclusions / p110 (0122.jp2)
- Bibliography / p112 (0124.jp2)