Mechatronics and computational mechanics II : selected, peer reviewed papers from the 2013 2nd International Conference on Mechatronics and Computational Mechanics (ICMCM 2013), December 30-31, 2013, Frankfurt, Germany
Author(s)
Bibliographic Information
Mechatronics and computational mechanics II : selected, peer reviewed papers from the 2013 2nd International Conference on Mechatronics and Computational Mechanics (ICMCM 2013), December 30-31, 2013, Frankfurt, Germany
（Applied mechanics and materials, v. 527）
Trans Tech Publications, c2014
- : pbk
Available at / 1 libraries
-
No Libraries matched.
- Remove all filters.
Note
Includes bibliographical references and indexes
Description and Table of Contents
Description
Collection of selected, peer reviewed papers from the 2013 the 2nd International Conference on Mechatronics and Computational Mechanics (ICMCM 2013), December 30-31, 2013, Frankfurt, Germany.
The 62 papers are grouped as follows:
Chapter 1: Materials Research,
Chapter 2: Applied Mechanics,
Chapter 3: Design, Modelling and Simulation,
Chapter 4: Robotic, Sensors and Control Systems,
Chapter 5: Information and Computer Technologies
Table of Contents
Preface and Committees
Chapter 1: Materials Research
Carbon Fiber Reinforced the Cracking Framework Top Side Columns Caused by Roof Temperature Deformation
Effect of Coarse Aggregate Type on the Residual Velocity of Rigid Projectile Perforating Concrete Target
Nanowelding of Single Walled Carbon Nanotubes onto Electrodes Using Molecular Dynamics Method
Preparation Process of Long Fiber Reinforced Impact Polypropylene Copolymer Composites
The Exploitation of Environmentally Friendly Materials for Humane Care in Children Postoperative Recovery
The Mechanical Properties of Cement Reinforced Loess and Pore Microstructure Characteristics
The Study for Non-Destructive Quantification Method of Reinforcement Corrosion Degree Based on Electrochemical Detection and Finite Analysis Technology
Chapter 2: Applied Mechanics
A Case Study on the Air Flow Characteristics of the Hirobo-FALCON 505 Controllable Helicopter's Main Rotor Blade
Computational Analysis of a Magnetohydrodynamic Flow in an Electrically Conducting Hairpin Duct
Flow Regime Identification for Wet Gas Flow Based on Kurtosis Feature of Flow-Induced Pipeline Vibration
Numerical Modeling on Low Velocity Impact on a Foam Core Sandwich Panel
Research on Horizontal Well Inhibiting Water Coning and Tapping the Potential of Remaining Oil
Research on the Aero Dynamicity of Steady Wing of Non-Parachute Terminal Sensitive Projectile
Stress Analysis and Applications of Sucker Rod in Deviated Wells
Study on Aftershocks Triggering by Static Stress Changes of the Minxian-Zhangxian 6.6 Earthquake
Study on the Production Decline Laws for Vertical Fracture Well in Low-Permeability Gas Reservoirs
The Numerical Simulation and Performance Analysis of the Vortex Pump for Solid-Liquid Two Phase Medium
Chapter 3: Design, Modelling and Simulation
Analysis of Modal and Seismic Property of Oil Storage Tanks
Calculation of Kill Probability for Kinetic Energy Rod against TBM Warhead
Design for Disassembly Based on Substance-Field Analysis
Optimization of Incremental Sheet Metal Forming Parameters by Design of Experiments
Overview of Visualization Tool as an Experimental Method in Iterative Participatory Design
Research for Calculation Model of Allotypic Pumping Unit Load
Research of Front-End Modeling Design for a SUV Based on Self-Piercing Riveting Anti-Fatigue Design
Solving the Deflection Problem of Laptop Casing Structure by Finite Difference Method
Dynamic Analysis on a Cable-Driven Interventional Active Catheter Using Kane's Method Combined with Screw Theory
Numerical Studies on the Performance of Saccardo Ventilation System in Emergency Fire Scenarios
Design and Optimization of Urban Signal Fuzzy Controller Based on IQPSO
Error Modeling and Simulation of Serial-Parallel Mechanism Based on Screw Theory
Structural Design and Performance Study of Parallel Metamorphic Mechanism Based on Screw System Theory
Missile Trajectory Simulation in Vertical Plane
Experimental Verification of the Suppression Effect of Ship Shaft-Rate Electric Field
Modal Analysis of a Electric Tool
An Efficient Quadratic Conversion Architecture for Real-Time Wideband DDC
Study on Development and Testing Mechanism of a New Multifunction Agricultural V-Belt Fatigue Testing Machine
Digital Structural Design and Research of Optical Microscope
Real-Time Suppression Research of Shaft-Rate Electric Field Based on the Compensated Negative Potential
Chapter 4: Robotic, Sensors and Control Systems
A Hybrid Approach Based on ACO and Ga for Multi Objective Mobile Robot Path Planning
Comparative Study of Motion Control Card Based on NI PXIe and cRIO Platform for Three-Axis Turntable
Design of Rate Gyro Stabilized Platform Control System
Robotic Fish Technology and its Applications to Space Mechatronics
Fuzzy Predictive Control Using Particle Swarm Optimization: Application to SCARA Robot
Design of Automatic Control System of Floating Dock
Design of New Intelligent Redundant Serial Bus with Isolated Driver in the Distributed Control System
Design of Pneumatic and Control System for Quartz Crystal Tin Dipping Machine
High-Speed Brushless DC Motor Current-Loop Sampling System Design for Three-Axis Turntable
Study and Application of Sliding Mode Control Strategy for High-Power Current Source Inverter
Chapter 5: Information and Computer Technologies
Design of a Communication Interface between the Controller and the Galvanometer
Reliability Evaluation of Main Electrical Connection of Substation Based on Graph Theory
Mechanical Disassembly of End-of-Life Products
Study on Development Techniques of AR Application Program in MFC Environmen
The Resource Conflict Resolution Problem for Virtual Cellular Manufacturing Inter-Cell Scheduling under the Conditions of Resource Sharing
Influencing Factors and Evaluation Standards of Vibration on Human Comfort
A New Wire Icing Automatic Monitoring System Based on Wireless Communication Platform
Capability Based Weapon System-of-Systems Evaluation Strategies Design Space and Exploratory Analysis
Material Demand Forecasting: An ERP System Perspective
Design of a Reconfigurable Extendible Real-Time Multi-Bus Simulation System on the Information Flow in the Control Systems
Risk Evaluation in Marine Traffic Systems Based on Fuzzy Catastrophe Theory
Approximate Evaluation of Exact Solutions of Measurements Inverse Problems
Research on Lower-Order Body Matrix Method and the Configuration Transformation of Planar Metamorphic Mechanism
Scene Classification Based on Improved Spatial Partition Model
Superconvergence Analysis of Finite Element Method for Onlinear Klein-Gordon Equation
by "Nielsen BookData"
