Operation and diagnostics of machines and production systems operational states II : special topic volume with invited peer reviewed papers only
Author(s)
Bibliographic Information
Operation and diagnostics of machines and production systems operational states II : special topic volume with invited peer reviewed papers only
（Applied mechanics and materials, v. 616）
Trans Tech Publications, c2014
- : pbk
Available at / 1 libraries
-
No Libraries matched.
- Remove all filters.
Note
Includes bibliographical references and indexes
Description and Table of Contents
Description
Volume is indexed by Thomson Reuters BCI (WoS).
Special Topic Volume entitled Operation and Diagnostics of Machines and Production Systems Operational States II is focused on the operation, technology and diagnostics of operational states of machines and manufacturing systems. The topic covers research fields that are mainly solved at the Faculty of Manufacturing Technologies of Technical University of Kosice with a seat in Presov for long period of time. Dealing with such kind of research is necessarily associated with high theoretical demands, so authors would like to disseminate achieved knowledge in research, educational and entrepreneurial areas.
Table of Contents
Preface
I. Theory, Diagnostics and Operational States of Machines
Diagnostic of Manufacturing Devices Operational States by Smart-Phones Application with Use of Augmented Reality Methods
Use of Diagnostic Methods for Monitoring of Disorder State of Production Machines and Equipment
Interactive Monitoring of Production Process with Use of Augmented Reality Technology
Bearing Units and Surface Micro-Geometry of Rolling Races in Textile Machinery
Implementation of Method and Structure Handling Manipulation Operations to Hydroabrasive Process
Modelling of the Anisothermal Phase Transformation of Austenite by Electromagnetic Sensor
Degradation Process in Area of Connecting Metal Sheets by Adhesive Bonding Technology in Agrocomplex
Mathematical Modelling and Optimization of Technological Process Using Design of Experiments Methodology
Boroscopy Application in Assurance of Technological Equipment Operational Capability
Diagnostics of the Arm Actuator Position Using Incremental Measurement
Experimental Investigation and Analysis of the Impact in Abrasive Mass Flow Changes with and without the Use of Sieve Analysis on Technological Head Vibrations at Hydroabrasive Cutting
Design of Module of Moving Robot
Operating Characteristics of Antagonistic Actuator with Pneumatic Artificial Muscles
Using Atomic Spectrometry and Volumetry Method for Determination of Bearing Corrosion in Tribotechnical Diagnostics of Engines
Determination of the Suitability of the Method Used for Evaluation Measurement Equipment Capability
Ensuring the Reliability of an Aircraft Engine Hydraulic System
Loops Control Structure and Solar System Control of a Multivalent Laboratory under Real-Time Mode
Monitoring of Biomass-Based Heat Production System
Impact of Lubrication Interval to Operating Status of Bearing
Analysis of Technological Head Working Pressure, Tilt Angle and Shift Impact to its Vibrations Using AWJ Technology
New Methods of Obtaining Input Data of Numerical Computations by Using Heat Treatment Simulator
Technological Head Tilt Angle Influence Analysis to Generation of Vibration during Ceramics Material Machining by Means of AWJ Technology
Progressive Technology Diagnostics and Factors Affecting Machinability
Diagnostic and Experimental Valuation on Progressive Machining Unit
Analysis of the Damage Causes of High Speed Bearing Failure
Monitoring of the Influence of Moisture Content in Thermoplastic Granulate on Rheological Properties of Material
Dynamic Analysis of Worm Gear Boxes
II. Operation of Production Systems
Diagnostics of Errors at Component Surface by Vision Recognition in Production Systems
Short-Term Testing of Cutting Materials Using the Method of Interrupted Cut
Dynamics of Core Taking out at Die Casting
Diagnostics of Strain Hardening Exponent and Material Constant of Steel Sheets
Using Recycled Rubber Particles as Filler of Polymers
Up Milling Technology and its Outputs
Assessment of Micro-Geometric and Macro-Geometric Parameters after Machining Composite Material with Natural Fibres
Comparison Measurement of the Distance between Axes of Holes with the Roundtest RA-120 and Thome Prazision-Rapid
Impact of Cutting Speed on the Resultant Cutting Tools Durability in Turning Process of Steel 100CrMn6
Comparison of Theory and Practice in Analytical Expression of Cutting Tools Durability for Potential Use at Manufacturing of Bearings
Analysis of Selected Properties of Cutting Ceramics at Machining Process of Bearing Steel 100Cr6
Chilled Ceiling Adaptive Control with Application of Parameters Gained from the Chilled Ceiling System Proposal Algorithm
Crystallization of Polylactic Acid Composites with Banana and Hemp Fibres by Means of DSC and XRD Methods
Influence of Processing Parameters Production of Sandwich Composite Structures Designed Especially for the Construction of Machine Tool Parts
Microstructural Characteristics Investigation of the Chip-Making Process after Machining
Stroke Design for the Press Roller on the Curling Twincylinder Machine
by "Nielsen BookData"
