Manufacturing science and technology VI : selected, peer reviewed papers from the 2015 6th International Conference on Manufacturing Science and Technology (ICMST 2015), June 1-2, 2015, Bandar Seri Begawan, Brunei
著者
書誌事項
Manufacturing science and technology VI : selected, peer reviewed papers from the 2015 6th International Conference on Manufacturing Science and Technology (ICMST 2015), June 1-2, 2015, Bandar Seri Begawan, Brunei
（Applied mechanics and materials, v. 789-790）
Trans Tech Publications, c2015
- : [set]
- Part 1
- Part 2
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the 2015 6th International Conference on Manufacturing Science and Technology (ICMST 2015), June 1-2, 2015, Bandar Seri Begawan, Brunei.
The 224 papers are grouped as follows:
Chapter 1: Materials and Technologies of Processing;
Chapter 2: Researching and Designing of Machines and Mechanisms;
Chapter 3: Applied Thermodynamics and Heat Transfer;
Chapter 4: Instrumentation and Measurement Technologies, Monitoring and Fault Detection;
Chapter 5: Designing and Development of Robots;
Chapter 6: Mechatronics;
Chapter 7: Theory and Practice of Control;
Chapter 8: Civil Engineering;
Chapter 9: Product Design, Product Quality and Rapid Prototyping;
Chapter 10: Industrial Engineering
目次
Preface, Committees and Sponsors
Chapter 1: Materials and Technologies of Processing
Finite Element Modeling of Frictional and Material Anisotropy During Forming of Steel Cylindrical Cups
Investigating the Degradation Resistance Improvement of Polymer Surfactant Complex Drag Reducing Agent
Microstructure and Fatigue Fracture of Spot Welded TRIP800 Steel
An Investigation of Machining Time and Surface Roughness in Wire-EDM for Inconel 800
Modified Stoney's Equation for Evaluation of Residual Stresses on Thin Film
Optical Methods for Studying the Drying Dynamics of Fe2O3 Nanocolloid Droplets Depending on Variation of Substrate Temperature
Experimental Study of Splitting Tensile Strength of Polymer Resin Grout with Fly Ash
Synthesis and Characterization of La10Si6O27 and Ce0.9Gd0.1O1.95 Solid Oxide Fuel Cell Electrolyte Material
Synthesis and Investigation of the Structural Properties of Al3+ Doped Mg Ferrites
YSr2Fe3-xCoxO8 as a Potential Cathode Materials for SOFCs
DFT/TD-DFT Studies on the Lawsone (Henna) as a Photosensitizer for Dye-Sensitized Solar Cells
Solder Ball Robustness Comparison between SAC 387 and Polymer Solder Balls under AC and TC Reliability Test
Effect of Microwave Absorber towards Pyrolysis Yield of Automotive Paint Sludge
Effect of Treating Time on Mechanical Properties and Structure of Aramid Fibers during Heat Drawing
The Effects of Melt Compounding Method on the Ambient and In Vitro Mechanical Properties of EVA/MMT Nanocomposites
Usage of Nano Silica in Synthetic Based Mud: A Comparison Study for High Temperature High Pressure Well
Processing Temperature of Sustainable Polymer with Thermoplastics by Injection Molding (Part 2)
Optical Properties of Cu2ZnSnSe4 Nanocrystalline Thin Films for Photovoltaic Devices
Effect of Cr on Grain Refinement and Mechanical Properties of Al-Si-Mg Alloys
Optimization of Multi-Performance Characteristics for a Hybrid Process of EDM and AJM Using Grey Relational Analysis
Machining Parameters Optimization for Trimming Operation in a Milling Machine Using Two Level Factorial Design
Application of Taguchi Method Machining to CuA1
Study on the Spring-Back Effect with Stress Distribution According to Forming Sheet Width in the Roll Forming Process
Hard Spots in ADC12 Die Casting Cylinder Block Used for Air Compressor
The Impact of Employing Different Quality PA2200 Powder Grades to Shrinkage on Sintered Part in Selective Laser Sintering Process
Study of Interfacial Shear of Aluminium/Oil Palm Empty Fruit Bunch Fiber Reinforced Polypropylene Fiber Metal Laminates
A Review on Ultrasonic Welding Capability: Breakaway from Traditional Plastic
Experimental Investigation to Improve Surface Integrity of Biomedical Devices by End-Milling AISI 316L Stainless Steel
Review on Effect of Repetitive Rework on Dissimilar Austenistic Stainless Steel Pipes by Using GMAW Orbital Welding
Surface Integrity in Micromilling of Hardened AISI D2 Tool Steel
Research of Elliptic Ultrasonic Vibration Mechanism
A Study on Dynamic Recrystallization Kinetics Model of 45Cr4NiMoV
Preheater for Anthracite Carbonization in Rotary Furnaces
Raman Analysis of Vanadyl Phthalocynine Layers for Plastic Electronic Applications
Chapter 2: Researching and Designing of Machines and Mechanisms
A Study with Diesel Additives and Fish Methyl Ester on Diesel Engine at Full Load Condition
Stratified Flow Condensation of CO2 in a Tube at Low Temperatures
Solar Powered Water Pump Lifting Agriculture
Analysis of the Inherent Frequency of Circular Vibrating Screen and Modelling and Simulation of Matlab/Simulink
The Design of the Nozzle for the Nozzle Box Microturbines
Topology Optimization of Wing Structure with Manufacturing Constraints
Design of Machine Tool Based on Reconfigurability Principles
Dynamic Analysis for Rotors of a Twin-Screw Compressor with Gas-Induced Cyclic Loads
Virtual Prototype Simulation and Transmission Error Analysis for RV Reducer
Study of the Influence of Labyrinth Seal Clearance on Gearbox Leakage with Gas-Fluid Two-Phase Mixture
Fatigue Finite Element Analysis of Certain Type of EMU Gearbox Box
Analysis of the Stability of Elliptical Journal Bearings under Vapor Cavitation Erosion
Sealing Performance of Thin Corrugated Metal Gasket
Improvement in CAM Shaft Design: An Experimental Application and Recommendation
Numerical Study of Fluid Behavior Induced by Anchor Impeller in a Stirred Vessel
Thermal Error Prediction of the Spindle Using Adaptive Neuro-Fuzzy Inference System
Efficiency Estimation of Thermoelectric Generators Application in the Liquefied Natural Gas Gasifiers
Research on Inspection Feature Recognition Based on Pro/E
3D Analysis of Crack Behavior Using XFEM
A Numerical Investigation of Laminar Mixed Convection Flow and Heat Transfer in a Lid Driven Cavity with Two Cylinders
Numerical Simulation of Radiation Losses in a Decaying Laser Spark Using LBL Method
The Impact of Different Axial Oil Chamber Design on Hydrostatic Spindle
Study on the Structure Parameters Simulation and Optimization for Stamping Quality of Plate Heat Exchanger
Optimal Cantilever Design by Topology and Shape Optimization Methods
Simulation Analysis of Planetary Gears Train of Semi-Direct Drive Wind Turbine Based on ADAMS
Numerical Study for Shape Oscillation of Free Viscoelastic Drop Using the Arbitrary Lagrangian-Eulerian Method
Analysis and Optimization of Erosion Wear Tester Design Parameters
Third Order ENO Scheme on Non-Uniform Grid for Supersonic Flows
The Effect of Mass Flow Distribution Inaccuracies in a Hydraulic Network Model for OD Zig-Zag Cooled Power Transformer Windings
Reliability of a Hydrodynamic Journal Bearing
A Supervisory Power Flow Controller for a Hybrid Power System
Study on the Dimensionless Model of High-Speed Penetration Efficiency
Numerical Investigation of Cavity Flow Field Characteristics in Supersonic Flow
Burners for Rotary Furnace - Proposal and Comparison
Innovative Design and Manufacturing Technology of High Temperature Air Combustion (HTAC) Municipal Solid Waste Incinerator
Failure Analysis of Composite Thin Walled Multi-Cell Closed Cross Section Beams with Multi-Tapered Configuration
Chapter 3: Applied Thermodynamics and Heat Transfer
Thermal Analysis of a Solar Powered ORC in Libya
Study of the Mixed Convection in a Horizontal Channel Heated from below
Natural Convection in an Annular Porous Medium: Effect of Brinkman Correction on the Bifurcation Point
Method of Heat Balances for Calculating Heat Transfer in Flat Multilayer Nanostructures
Simulation Research on the Hydraulic and Thermal Operation for Complex District Heating System
Field Evaluation of Five-Level Heat Dissipation Models under PV Array Structure Installed in the Tropics
Circulation Effectiveness of Working Fluid in Inclined Micro Heat Pipes
Numerical Procedure for LMTD Correction Factor Calculation for One Tube and One Shell Pass Shell-and-Tube Heat Exchangers
ANSYS Analysis on Thermal Structure of Bionic Brake Discs
Development of a Plasma-Dump Combustor for VOC Destruction
A Differential Quadrature Method for Solving Multi-Dimensional Inverse Heat Conduction Problem
The Nonlinear Multi-Fuel Combustion Equation: Comparison between the Model of Heat in SIE for Ethanol-Gasoline Blended and High Order Iteration Method
Numerical Determination of the LMTD Correction Factor for Shell-and-Tube 1-2 Heat Exchangers
Natural Convection for Air and Molten Gallium in Square- and Elbow-Shaped Enclosures
The Simulation of Molecular Return Flux in Thermal Vacuum Test of Spacecraft
Significant of Isothermal Flow Studies for High Swirling Flow in Unconfined Burner
Numerical Simulation of Turbulent Thermal Fluid in Tee Water Duct Cooled Nuclear Reactor
Experimental Analysis of the Pool Boiling Phenomenon of Sugarcane Juice
Cooling Profile Analysis of Hot Strip Coil Using Finite Volume Method
Application of PTFE Heat Exchanger in Low Temperature Waste Heat of Big Coal-Fired Power Plants
Chapter 4: Instrumentation and Measurement Technologies, Monitoring and Fault Detection
A W-Band Dual-Mode Band-Pass Filter Based on LTCC Technology
A Millimeter-Wave SIW Gain Equalizer Using LTCC Technology
Dew Point Measurement Error due to Tube Length in a Calibration Instrumentation and the Evaluation of Measurement Uncertainty
A Neural Based Fuzzy Logic Model to Determine Corrosion Rate for Carbon Steel Subject to Corrosion under Insulation
Research on Automatic Programming and Process Diagnosis in On-Machine Measurement
New Test System of Infrared Earth Sensor
Experimental Measurements of Pressure Losses in the Inter-Turbine Duct of a Gas Turbine
Using Infrared Thermograph of Chip Temperature to Monitor Cutting Edge Performance
Chemiresistor Gas Sensor Array Based on Conducting Polymers for the Discrimination of Virgin Coconut Oil
Sea Bed Logging Applications: Predicting Hydrocarbon Depth Using Mathematical Equations
Coal-Rock Character Recognition in Fully Mechanized Caving Faces Based on Acoustic Pressure Data Time Domain Analysis
Modeling and Analysis of a Novel Flexible Capacitive-Based Tactile Sensor
Smart Diagnosis Using an On-Board Middleware
An Equivalent Condition Score Method for the Calculation of the Failure Rate for Power Transmission Equipment with Condition Maintenance
Fault Detection and Diagnosis in Gears Using Wavelet Analysis Techniques and Comparison on their Diagnostic Capability
Solving the Issue of Electronic Breakdown of Hobbing Machine through Kobetsu Kaizen Methodology: A Case Study
Intelligent Diagnostic of Induction Machine for Faults Detection and Classification Using Wavelet and Fuzzy Inference
Control Valve Fault Detection Based on Acoustic Emission Signal
Verification of Faulty Mechanism for Fan-Out Wafer Level Package Using Numerical Analysis
Chapter 5: Designing and Development of Robots
Model Predictive Control for Tendon-Driven Balloon Actuator under Constraints on Simulation
Investigation of the Influence of the Wings and Tail in Flight of the Jumping Robot
Development and Validation of the Kinematic Analysis of a Low Low-Cost 4-Link Robot
Simulation and Determination of the Influence of the Gait Function on the Change of the Shape of a Snake-Like Robot
A New Method to Solve the Kinematic Problem of Parallel Robots Using an Equivalent Structure
A Low Cost Robotic Wheelchair System Using a Pan-Tilt Camera and a Visual Marker
A Novel Dual-Loop Control Scheme for Payload Anti-Swing and Trolley Position of Industrial Robotic 3DOF Crane
Mechanical Analysis of a Hybrid Approach for a Lower Limb Rehabilitation Robot
A Framework of In Situ Model Error Compensation for Adaptive Robotic Task Execution
Hardware-in-the-Loop Test Platform Design for UAV Applications
The Motion Planning for Spherical Robot with Two Motors
Intelligent Control System Design for a Teleoperated Endoscopic Surgical Robot
Mathematical Model Based Attitude Control of Inverted Pendulum Type Mobile Robot
Design Guidelines for an Embedded Permanent Magnetic Matrix Wheel Climbing Robot
Increase the Space Trajectory Precision by Using the Proper Assisted Research Method for Inverse Kinematics Problem
KSU-IMR Mobile Robot Navigation Maps Building and Learning
Dynamic Optimization of a Three Translational Degrees of Freedom Parallel Robot Based on a Multi-Objective Genetic Algorithm
Modeling and Control of a Robot Arm on a Two Wheeled Moving Platform
Mars-500 Program Space-Based Mobile Robot "Turist"
Modelling of the Human's Leg as a Switched Linear System
The Design of a Multifunctional Remote-Control Intelligent Vehicle Based on STC89C52
Synthesis of Seven-Bar Linkage with Two DOF for Body Guidance
Simulation-Based Analysis of a Linear Switched System Based on Human Arm's Dynamics
A Clustering and Outlier Detection Scheme for Robust Parametric Model Estimation for Plane Fitting
Chapter 6: Mechatronics
Cooling Performance Analysis of the Permanent Magnet Motor
Design on Electric Vehicle Battery Management System with FlexRay Bus
The Impact of Different Direct-Driving Motor Design on Swivel Spindle Head
Stability Control of Electric Vehicles with Two-Motor-Wheel Drive
A Unifying Model for Mechatronic Systems Specification
Investigation of Relation between Straightness and Cutting Force in CNC Turning Process
A Systematic Approach for Modeling and Analyzing Mechanical Assemblies that Require Remote Handling
Instruction Format Design for Low Power Embedded Systems
Data Cluster Detection for Low Power Embedded Memory Subsystems
Stress-Strain Behaviour of Dielectric Elastomer for Actuators
Fractional Order Modeling and Analysis of Buck-Boost Converter
The Turning Speed of Stability Control in Electric Learner-Driven Vehicle Driving
Innovative Algorithm and Software for Three-Dimension Topography Evaluation in Laser-Micro Machining
Finite Element Analysis on Vibration of a Piezoelectric Micro Pump
Simulation of Closed Loop Electro-Hydraulic Actuator Using PID Based on AMESim
Automatic Recognition of Multi-Axis Machining Features Based on Machining Process from 3D Solid Model
Control Strategy and Deterministic Optimization Research for Parallel Compound Braking System
Extended Modeling of Vertical Axis Motion Dynamics of VTOL Vehicle
Kinematics Optimization of a 3-SPS Parallel Redundant Motion Mechanism Using Conformal Geometric Algebra
Design of Transfer Alignment for Micro-Inertial Attitude Measurement System Based on Distributed
A Study on Influence of System Parameters on Servo Pneumatic System and Multi-Response Optimization Using Taguchi - Grey Methodology
A Study on Slip Controller for Safety Improvement of Running Flat Road for Motorized Wheelchair
Ground Semi Active Damping Force Estimator (gSADE) for Magnetorheological Damper Suspension System Using Quarter Heavy Vehicle Model
Optimal State Feedback Controller Design for Vibration Attenuation in a Class of Image Transfer Belt
Proportional Derivative Controller Using Discrete Kalman Filter Estimation Method for Spacecraft Attitude Control
Skid Control of Small Electric Vehicles with In-Wheel Motors (Effect of ABS and Regenerative Brake Timing Control on Emergency Braking)
Predictive Functional Control for a Pneumatic Cylinder
Development and Implementation of an Automated Car Parking System
Adaptive Fuzzy Sliding-Mode Position Control of a Shape Memory Alloy Actuated System
Estimation of Unknown Disturbances in Gimbal Systems
Tire Force Control Strategy for Semi Active Magnetorheological Damper Suspension System Using Quarter Heavy Vehicle Model
Sensorless Control Based on Virtual Neutral Voltage for BLDC Motor Drive
Vibration Control of Strain Gradient Nonlinear Micro-Cantilevers Using Piezoelectric Actuators
Independent Control of Force & Displacement Using Shape Memory Alloy Tactile Display
Computational Simulation and Experimental Validation on Safe-Flight Control for a Six-Rotor Craft
A Grating Monopole Antenna on Metamaterial Using MSRR for DVB-T Application
Chapter 7: Theory and Practice of Control
Predictive Functional Control of a Table Drive System Using Disturbance Observer and Preview Feedforward Controller
A New Variable Structure Control Scheme for Mismatched Uncertain Large Scale Systems
Reactive Power Control of Reversible Electric Drives by Using Industrial Smart Grid Technology
Development of an Experimental Setup for the Altitude Control of a Ball in a Pipe
Adaptive Optimal Digital PID Controller
On the Reducibility of the Discrete Linear Time-Varying Systems
Prescheduled Controller for Split Unit Air Conditioner Reduce Energy Consumption
Optimisation of a PID Controller for an Inverted Pendulum Using the Bees Algorithm
Trajectory Controllability of Semilinear Systems with Delay in Control and State
Properties of the Lower Bohl Exponents of Diagonal Discrete Linear Time-Varying Systems
Providing Security of Vital Data for Conventional Microcontroller Applications
An Affine Parameter Dependent Controller of an Helicopter for Various Forward Velocity Conditions
A Systematic Approach for Optimal Design of SVC Controller to Reduce the Disturbances in Electric Arc Furnace Using Generic Algorithm
The Dipole Magnets Temperature Monitoring and Interlocking Protection System of HIRFL-CSRm
Development of a Cloud Based Remote Mobile Monitoring and Control System for Manufacturing
Analysis and Initialization of GE Wind Turbine Control Model
On PID-Controller Parameters Neural Tuner Usage for Nonlinear Plants Control
Chapter 8: Civil Engineering
Fabrication of High Strength Concrete from Recycled Concrete Aggregate Utilizing Taguchi Method
Investigation of Wind around Buildings of Different Heights Using an Environmental Wind Tunnel
Identifying Radius of Rebar Buried in Concrete Massif by Using Electromagnetic Penetrating Radar
Evaluation of the Use of a Solar Source for Air Conditioning for Home in Algeria
Numerical Modeling of Wind around Buildings of Different Heights
Grouted Pipe with Double Spirals for Precast Concrete Connections
Seismic Performance Improvement of 3D Reinforced Concrete Frames with Different Strengthening Applications
Sustainable Manufacturing Processes of Building Materials: Energy Efficiency
Heating or Cooling Buildings with PV Walls in Reunion Island
Influence of Very Old Masonry in the Seismic Damage of an Historic Tower
The Study of the Multichannel Solar Chimney Ventilation Performance
Effects of Wetting on the Soil Fabric of Compacted Clay
Fiber Reinforced Composite Materials in Architecture
Performance of Grouted Splice Sleeves with Tapered Bars under Axial Tension
The Statistical Verification of Significance of Airtightness and Energy Performance
Chapter 9: Product Design, Product Quality and Rapid Prototyping
Applying P-Diagram in Product Development Process: An Approach towards Design for Six Sigma
Evaluation of Product Quality Using Standardized Distance from Target
Using the Fuzzy-QFD for Product Development: A Case Study for 3D Printer
Design of Experiment - An Integration of Fisher, Taguchi and Shainin DOE Methodology
Rapid Prototyping Technology: The Next Keystone for Small and Medium Ceramic Industry
A Roll Powder Sintering Additive Manufacturing Technology
The Manufacture of Molar and Dental Bridge through 3D Printing
Image Processing of Product Surface Defect Using Scilab
Chapter 10: Industrial Engineering
Genetic Modelling for Selecting Optimal Machine Configurations in Reconfigurable Manufacturing System
A Productivity Improvement of a Packing Line
Modeling of Order Oriented Planning for Printed Circuit Board Assembly Line
Re-Layout and Robust Machine Layout Design under Stochastic Demand
Construction of a Cloud Manufacturing Platform for Service Sharing in Manufacturing Industry Park
Improving Quality Control Plan of Flexible Printed Circuit
An Optimization of Automated Process Planning for Manufacturing Prismatic Parts on a Machining Center
Virtual Reality for Manufacturing Engineering in the Factories of the Future
An Application of Value Stream Mapping in Ceramic Tile Industry: A Case Study
The Effect of Unforeseen Disruption on Different Types of Manufacturing Industry-Layout
A Heuristic Approach for Type 2 Assembly Line Balancing Problem
Study Concerning the Increase of Productivity in Machining by Lapping
A Unified Measure to Assess Universally Industrial Products for Ecological Balancing
Modeling the Collaborative Design of the Automotive Powertrain System Based on the Design Structure Matrix
New Methods of Mining Technological System's Performance Analysis
「Nielsen BookData」 より
