|
表紙
Full Text:
CiNii
|
|
|
目次
Full Text:
CiNii
|
|
|
複写される方へ
Full Text:
CiNii
|
|
|
CONTENTS
Full Text:
CiNii
|
|
|
A編目次
Full Text:
CiNii
|
|
|
B編目次
Full Text:
CiNii
|
|
|
Stabilization Control for Hunting Motion of Railway Vehicle by Gyroscopic Damper : Experimental Analysis Using 1/10 Scale Vehicle Model(Mechanical Systems)
Full Text:
CiNii
|
235-241
|
|
Basic Study of Wheel Flange Climbing Using Model Wheelset(Mechanical Systems)
Full Text:
CiNii
|
242-249
|
|
Experimental Reproduction of Accident Prone Area Using a Driving Simulator and Behavioral Analyses in Traffic Conflicts(Mechanical Systems)
Full Text:
CiNii
|
250-258
|
|
Energy Regenerative Vibration Control of Smart Structure Using Class D Amplifier : 1st Report, Numerical Study Using Equivalent Circuit Model and Circuit Simulator(Mechanical Systems)
Full Text:
CiNii
|
259-268
|
|
Active Switching Vibration Control Based on the Frequency for Double-layered Structure(Mechanical Systems)
Full Text:
CiNii
|
269-277
|
|
Frequency Estimation Method Using the Adaptive Algorithm and Application to Dynamic Measurement of Mass and Weight(Mechanical Systems)
Full Text:
CiNii
|
278-284
|
|
Simulation Study on Reduction of Heat-Induced Head-Alignment Errors and Main-Resonance Amplitudes for Pivot-Shaft-Combined Head-Positioning Mechanisms(Mechanical Systems)
Full Text:
CiNii
|
285-292
|
|
An Experimental Study of Reduction for Aerodynamic Excitation to Head-Arm of HDD(Mechanical Systems)
Full Text:
CiNii
|
293-301
|
|
Analysis of a Pumping Module Using EHD Fluid(Mechanical Systems)
Full Text:
CiNii
|
302-308
|
|
Simplified Analysis Method for Pyroshock Responses Near the Pyroshock Source Induced by V-band Clamp Separation Devices(Mechanical Systems)
Full Text:
CiNii
|
309-317
|
|
Response Reduction Map of Gap System Based on Energy(Mechanical Systems)
Full Text:
CiNii
|
318-323
|
|
Modeling and Control of Individual Cylinder Air-Fuel Ratio in Multi-Cylinder Engine with Single Sensor(Mechanical Systems)
Full Text:
CiNii
|
324-331
|
|
Study on Acoustic Characteristics of Straight Duct with Some Holes(Mechanical Systems)
Full Text:
CiNii
|
332-338
|
|
Modeling and Cooperative Resister Control of Gravure Printing Press(Mechanical Systems)
Full Text:
CiNii
|
339-345
|
|
Task Instruction to a Robot by Putting Task Information in a Work Space(Mechanical Systems)
Full Text:
CiNii
|
346-352
|
|
Mobile Robot Navigation Using Trajectory of Laser Spot(Mechanical Systems)
Full Text:
CiNii
|
353-358
|
|
Shape Memory Alloy Actuator for Artificial Muscle : Characteristics of Motor Unit(Mechanical Systems)
Full Text:
CiNii
|
359-364
|
|
A Basic Study for Leg-swing Motion of Passive Walking(Mechanical Systems)
Full Text:
CiNii
|
365-371
|
|
Muscle Scraping Manipulator for Minimally Invasive Hip Joint Surgery : System Design and Evaluation of the Workspace(Mechanical Systems)
Full Text:
CiNii
|
372-379
|
|
A Walking Pattern Generator Using a Spherical Inverted Pendulum with an Underfloor Pivot(Mechanical Systems)
Full Text:
CiNii
|
380-385
|
|
Development of Power-Assisted Wheelchair with H_∞, Control to Maintain Robustness Against Load Uncertainty(Mechanical Systems)
Full Text:
CiNii
|
386-394
|
|
Modeling of One-Degree-of-Freedom Finger-Grasp System with Tendon Organ Reflex and Stretch Reflex(Mechanical Systems)
Full Text:
CiNii
|
395-399
|
|
Measurement of Forearm Trajectory During Pitching Motion Using Elbow-mounted Sensor(Mechanical Systems)
Full Text:
CiNii
|
400-408
|
|
The Basic Analysis for Object Zone Detection with Volume Intersection Method Using Omni-Directional Vision Sensors for Man-Machine Co-Existence Systems(Mechanical Systems)
Full Text:
CiNii
|
409-416
|
|
Increase of Traction Coefficient due to Microtexture : 1st Repor, Effect of Orientation in Microtexture(Machine Elements and Manufacturing)
Full Text:
CiNii
|
417-424
|
|
Thermal Lubrication Characteristics of Swash-Plate Type Axial Piston Pumps : Temperature Measurement of Swash-Plate and Cylinder-Block(Machine Elements and Manufacturing)
Full Text:
CiNii
|
425-430
|
|
Possibility of the Analysis of Two-Dimensional Inverse Problems in Hydrodynamic Lubrication : An Examination Using a Plane Inclined Bearing with Finite Width(Machine Elements and Manufacturing)
Full Text:
CiNii
|
431-438
|
|
Analysis of Contact Pressure Acting on a Thermal Print Head of a Dye Sublimation Printer(Machine Elements and Manufacturing)
Full Text:
CiNii
|
439-445
|
|
Analysis of Internal Modified-Layer Formation Mechanism into Silicon Single Crystal with Nanosecond Laser(Machine Elements and Manufacturing)
Full Text:
CiNii
|
446-452
|
|
A Truing Technique for Flattening Fine Diamond Grains on the Hemispherical Working Surface of an Electroformed Tool(Machine Elements and Manufacturing)
Full Text:
CiNii
|
453-458
|
|
Collaboration Support System Based on Assessment of Created Ideas Using Data Envelopment Analysis(Machine Elements and Manufacturing)
Full Text:
CiNii
|
459-466
|
|
A Heuristic Algorithm for a Task Assignment Problem of Minimizing the Cycle Time(Machine Elements and Manufacturing)
Full Text:
CiNii
|
467-474
|
|
A Study on Openability of an Aluminum Beverage Bottle(Machine Elements and Manufacturing)
Full Text:
CiNii
|
475-483
|
|
Effects of Monozukuri Curriculum to Promote Participation of Lower Grade Students in Graduation Research at Technical College : Development of 5-inch Locomotive Model Set(Machine Elements and Manufacturing)
Full Text:
CiNii
|
484-490
|
|
日本機械学会論文集「ノート」欄の新設について
Full Text:
CiNii
|
|
|
2007年度(第85期)論文編修部会
Full Text:
CiNii
|
|
|
討論について
Full Text:
CiNii
|
|
|
支部所在地
Full Text:
CiNii
|
|
|
奥付
Full Text:
CiNii
|
|
|
裏表紙
Full Text:
CiNii
|
|
