Search Results1-20 of  60

  • 1 / 3
  • 広垣 俊樹 ID: 9000007378888

    Articles in CiNii:1

    • CAD/CAEを活用した機械設計教育 (特集 バーチャルプロトタイピングの実際と可能性--身近になった機構解析ツールの活用テクニック) -- (教育現場からの報告) (1999)
  • 廣垣 俊樹 ID: 9000242679005

    Articles in CiNii:1

    • Ball end mill condition derived from catalog mining and evaluation of the application by classified inclination angle (2013)
  • 廣垣 俊樹 ID: 9000242679091

    Articles in CiNii:1

    • Fabrication of magic-mirror surface by in-situ magnetic polishing method with a machining center (2013)
  • 廣垣 俊樹 ID: 9000242693044

    Articles in CiNii:1

    • Fiber Laser Cutting and Hole Preparation for the Aircraft CFRP Materials : Minimizing of Heat Affected Zone by Laser (2012)
  • 廣垣 俊樹 ID: 9000242693364

    Articles in CiNii:1

    • Improvement of the Process Efficiency for End-mill Processes by an Infrared Imagery (2012)
  • 廣垣 俊樹 ID: 9000364866473

    Articles in CiNii:1

    • 110 プリント基板用 GFRP 積層材の小径ドリル加工時の損傷幅に対する要因 (1997)
  • 廣垣 俊樹 ID: 9000364866476

    Articles in CiNii:1

    • 111 プリント基板用 GFRP 積層材の小径ドリル加工時の損傷評価とその対策 (1997)
  • 廣垣 俊樹 ID: 9000364943781

    Articles in CiNii:1

    • 504 レーザを用いたプリント基板の小径ブラインドホール加工 : アラミドおよびガラス不織布強化基板の比較 (1998)
  • 廣垣 俊樹 ID: 9000364985818

    Articles in CiNii:1

    • 607 FRP歯車における設計システムの開発 : 積層材料を用いた歯車における曲げ疲労強度の算定(破壊と破壊力学-I)(複合材料の産業応用)(オーガナイスドセッション6) (2003)
  • 廣垣 俊樹 ID: 9000402589674

    Articles in CiNii:1

    • A Monitoring Technology of Gear Meshing based on Combination of Continuous Shots with a Thermography and Analysis of Tooth Surface Temperature by Heat Circuit Network Model (2019)
  • 廣垣 俊樹 ID: 9000404657882

    Articles in CiNii:1

    • 最近のメルトブロー不織布ナノファイバーとその応用性能 (2019)
  • 廣垣 俊樹 ID: 9000405647225

    Articles in CiNii:1

    • Optimal Design of Work Ejector Shaft for Automatic Work Discharge System in Counter-Spindle NC Lathe Based on Application of Quality Engineering (2019)
  • 廣垣 俊樹 ID: 9000406372548

    Articles in CiNii:1

    • Smart monitoring method based on image process of chatter mark on end-milled surface (2020)
  • 廣垣 俊樹 ID: 9000410184512

    Articles in CiNii:1

    • Influence of difference of servo characteristics between straight axis and rotating axis on motion error and machining performance of complex geometry workpieces with a five axis machining center (2014)
  • 廣垣 俊樹 ID: 9000410753229

    Articles in CiNii:1

    • Development of automatic work-piece ejector for two opposing spindle lathes based on Quality engineering (2020)
  • HIROGAKI Toshiki ID: 1000080275172

    Articles in CiNii:614

    • レーザスタイラスを用いた機上計測システムの開発 -研削ホイールの作業面形状測定- (1996)
    • 砥石作業面トポグラフィーのオン・ザ・マシン計測に関する研究 -ドレッシング条件が及ぼす影響について- (1996)
    • レーザスタイラスを用いた金型の3次元形状測定 (1996)
  • HIROGAKI Toshiki ID: 9000256259482

    Articles in CiNii:1

    • Characteristics of Meshing in Spiral Bevel Gears. (Comparison of the Gleason-type Gear with the Oerlinko-type Gear). (1991)
  • HIROGAKI Toshiki ID: 9000256267040

    Articles in CiNii:1

    • A Study on Dynamic Behavior of the Oerlikon-type Spiral Bevel Gears. Rotational Vibration of Gears under Running Conditions. (1996)
  • HIROGAKI Toshiki ID: 9000256270473

    Articles in CiNii:1

    • Study on Super-finishing by CBN Stone. Estimation of Cutting performance using Average crossing angle. (1998)
  • HIROGAKI Toshiki ID: 9000256272847

    Articles in CiNii:1

    • Monitoring of Rotational Behavior on Spiral Bevel Gears. (2000)
  • 1 / 3
Page Top