Search Results1-20 of  120

  • Hangai Yoshihiko ID: 9000241868202

    Articles in CiNii:1

    • Fabrication of Large-Scale Porous Aluminum by Enhanced Friction Powder Compaction Process through Traversing Tool Based on Sintering and Dissolution Process (2013)
  • Hangai Yoshihiko ID: 9000398825899

    Articles in CiNii:1

    • Forming of Aluminum Foam Using Light-Transmitting Material as Die during Foaming by Optical Heating (2018)
  • HANGAI YOSHIHIKO ID: 9000238063042

    Articles in CiNii:1

    • Deformation Behavior Estimation of Aluminum Foam by X-ray CT Image-based Finite Element Analysis (2013)
  • HANGAI Yoshihiko ID: 9000001826954

    Department of Mechanical System Engineering, Faculty of Engineering, Gunma University (2006 from CiNii)

    Articles in CiNii:1

    • Pore Defect Control in Die Casting by Compression Loading (2006)
  • HANGAI Yoshihiko ID: 9000002116875

    Graduate School of Engineering, Gunma University (2012 from CiNii)

    Articles in CiNii:10

    • Quantitative Evaluation of Porosity in Aluminum Die Castings by Fractal Analysis of Perimeter (2008)
    • Foaming Conditions of Porous Aluminum in Fabrication of ADC12 Aluminum Alloy Die Castings by Friction Stir Processing (2009)
    • Effects of Tool Rotating Rate and Pass Number on Pore Structure of A6061 Porous Aluminum Fabricated by Using Friction Stir Processing (2010)
  • HANGAI Yoshihiko ID: 9000003799701

    Graduate school of Science and Engineering, Gunma University (2015 from CiNii)

    Articles in CiNii:102

    • Large Scale Atomistic Simulation of Cu/Al_2O_3 Interface via Quasicontinuum Analysis (2005)
    • Quasicontinuum Analysis of Alumina/Copper Interface (2005)
    • Reduction of porosity in aluminum alloy die castings by compression load (2006)
  • HANGAI Yoshihiko ID: 9000003815187

    Institute of Industrial Science, University of Tokyo (2001 from CiNii)

    Articles in CiNii:1

    • Applicability of Compounded Mesh Pattern to Three-Dimensional Interface Problems(Modeling & Simulation) (2001)
  • HANGAI Yoshihiko ID: 9000003817848

    Institute of Industrial Science, University of Tokyo (2002 from CiNii)

    Articles in CiNii:3

    • Examination of Fundamental Properties of Three-Dimensional Interface Crack Parameter by the Compounded Mesh Method (2002)
    • Applicability of Compounded Mesh Method to Three-dimensional Interface Problems : 1st. Report, Formulation and Application to Interface Edge Problems (2002)
    • Applicability of Compounded Mesh Method to Three-Dimensional Interface Problems : 2nd. Report, Application to Interface Crack Problems (2002)
  • HANGAI Yoshihiko ID: 9000019989579

    Department of Mechanical System Engineering, Graduate School of Engineering, Gunma University (2010 from CiNii)

    Articles in CiNii:1

    • Effects of Amount of Added Alumina and Holding Time on Manufacture of Porous Aluminum by Utilizing Friction Stir Processing (2010)
  • HANGAI Yoshihiko ID: 9000020062440

    Graduate School of Engineering, Gunma University (2011 from CiNii)

    Articles in CiNii:1

    • Pore Collapsed Behavior of Porous Aluminum during Compression Process by Using X-Ray CT Nondestructive Observation (2011)
  • HANGAI Yoshihiko ID: 9000020192953

    Graduate School of Engineering, Gunma University (2011 from CiNii)

    Articles in CiNii:1

    • Manufacturing of A1050-A6061 Functionally Graded Porous Aluminum (2011)
  • HANGAI Yoshihiko ID: 9000020262088

    群馬大学大学院 工学研究科 (2011 from CiNii)

    Articles in CiNii:1

    • Manufacturing of Porous Aluminum Component by Using Die (2011)
  • HANGAI Yoshihiko ID: 9000020262210

    群馬大学大学院 工学研究科 (2011 from CiNii)

    Articles in CiNii:1

    • Equivalent Elastic Property of Cast Aluminum Alloy around Clustered Shrinkage Pores (2011)
  • HANGAI Yoshihiko ID: 9000020295894

    群馬大学大学院工学研究科 (2011 from CiNii)

    Articles in CiNii:1

    • Investigation of Manufacturing Process of ADC12-A1050 Porous Aluminum by Friction Stir Processing Route (2011)
  • HANGAI Yoshihiko ID: 9000020295956

    群馬大学大学院 工学研究科 (2011 from CiNii)

    Articles in CiNii:1

    • Manufacturing of Sandwich Panel with Porous Aluminum/Dense Steel Plate by Friction Stir Processing Route (2011)
  • HANGAI Yoshihiko ID: 9000021408323

    Department of Mechanical System Engineering, Gunma University (2008 from CiNii)

    Articles in CiNii:1

    • X-Ray CT Inspection for Porosities and Its Effect on Fatigue of Die Cast Aluminium Alloy (2008)
  • HANGAI Yoshihiko ID: 9000021475205

    群馬大学大学院 工学研究科 (2011 from CiNii)

    Articles in CiNii:1

    • Quantitative Evaluation of Porosity Effect on Fatigue Strength of High Pressure Die Cast Aluminum Alloy (Part 1, Experimental Investigation for Effect of Porosity and Casting Surface) (2011)
  • HANGAI Yoshihiko ID: 9000021539554

    群馬大学大学院 工学研究科 (2011 from CiNii)

    Articles in CiNii:1

    • Quantitative Evaluation of Porosity Effect on Fatigue Strength of High Pressure Die Cast Aluminum Alloy (Part 2, Fatigue Strength Prediction Based on Elastic Stress Field around Pores) (2011)
  • HANGAI Yoshihiko ID: 9000021596176

    Graduate School of Engineering, Gunma University (2011 from CiNii)

    Articles in CiNii:1

    • Manufacturing of ADC12-A1050 Functionally Graded Porous Aluminum by Friction Stir Processing Route (2011)
  • HANGAI Yoshihiko ID: 9000107309591

    Department of Mechanical System Engineering, Graduate School of Engineering, Gunma University (2012 from CiNii)

    Articles in CiNii:1

    • Relationship between Porosity and Interface Fracture on Aluminum Foam Sandwich with Dense Steel Face Sheets Fabricated by Friction Stir Processing Route (2012)
Page Top