Search Results21-40 of  128

  • OGAWA Keiji ID: 9000303645327

    滋賀県立大学工学部 (2013 from CiNii)

    Articles in CiNii:1

    • S132011 Investigation of Side Cutting Phenomena in Micro End-milling : Influence of Feed Rate (2013)
  • OGAWA Keiji ID: 9000304303166

    The University of Shiga Prefecture (2012 from CiNii)

    Articles in CiNii:1

    • B28 Influence of Cutting Edge Shape of Ball End Millon its Life (2012)
  • OGAWA Keiji ID: 9000308045027

    The University of Shiga Prefecture (2013 from CiNii)

    Articles in CiNii:1

    • 607 Micro Drilling of Stainless Steel Plate by Pulsed Laser (2013)
  • OGAWA Keiji ID: 9000308045031

    The University of Shiga Prefecture (2013 from CiNii)

    Articles in CiNii:1

    • 608 High Efficiency Grinding of Zirconia-toughened Alumina Ceramics : Evaluation Based on Undeformed Chip Shape (2013)
  • OGAWA Keiji ID: 9000308713912

    The University of Shiga Prefecture (2014 from CiNii)

    Articles in CiNii:1

    • 403 A Consideration of Mechanism for Cutting of High Manganese Steel (2014)
  • OGAWA Keiji ID: 9000308715056

    The University of Shiga Prefecture (2014 from CiNii)

    Articles in CiNii:1

    • 407 Investigation of Cutting Phenomena in Micro End-milling : About Shoulder Cutting (2014)
  • OGAWA Keiji ID: 9000321628362

    Department of Mechanical and Systems Engineering, Ryukoku University (2016 from CiNii)

    Articles in CiNii:1

    • Quality control method of blind via hole based on monitoring Cu direct laser processing in high heat radiation printed circuit board with a high speed camera (2016)
  • OGAWA Keiji ID: 9000329418097

    Dept. of Mechanical and Systems Engineering, Ryukoku University (2015 from CiNii)

    Articles in CiNii:1

    • 0201 Influence of Servo Activation Frequency on Servo Motor Temperature of Machine Tools Equipped with Idling Reduction System (2015)
  • OGAWA Keiji ID: 9000329418384

    Faculty of Science and Engineering, Ryukoku University (2015 from CiNii)

    Articles in CiNii:1

    • 1011 Magnetic Polishing of Micro Channel using a Ball-Nose End-Mill Type Tool with a Compact Machine Tool (2015)
  • OGAWA Keiji ID: 9000329418440

    Ryukoku University (2015 from CiNii)

    Articles in CiNii:1

    • 1202 Laser Irradiation Control Method in Via-Hole Drilling of Printed Wiring Board Based on High Speed Camera Monitoring (2015)
  • OGAWA Keiji ID: 9000329418585

    Department of Mechanical Engineering, Doshisha University (2015 from CiNii)

    Articles in CiNii:1

    • 1601 Fabrication of Complex Shape Products Made of Binder-free Green Composite using Bamboo Fibers Extracted with a Machining Center (2015)
  • OGAWA Keiji ID: 9000329418669

    Dept. of Mechanical and Systems Engineering, Ryukoku University (2015 from CiNii)

    Articles in CiNii:1

    • 1903 Investigation of Micro-Drilling Conditions of Printed Wiring Board Based on Data-mining of Catalog Information (2015)
  • OGAWA Keiji ID: 9000329418701

    Ryukoku University (2015 from CiNii)

    Articles in CiNii:1

    • 2105 Experimental Investigations on Micro-end-milling of Hardened Die Steel : Fundamental Phenomena in Shoulder Cutting (2015)
  • OGAWA Keiji ID: 9000364986293

    Articles in CiNii:1

    • 317 Factor analysis of quality of micro-drilling hole in multilayer PWB that uses data mining (2005)
  • OGAWA Keiji ID: 9000364986294

    Articles in CiNii:1

    • 318 Application of GFRP Plate to Build-up Layer of Multi Layer Printed Wiring Boards for Cu Direct Blind Via Hole Drilling using CO_2 Laser (2005)
  • OGAWA Keiji ID: 9000364986483

    Articles in CiNii:1

    • 628 Manufacturing and Controlling of Bamboo Fibers Obtained with a Machining Center (2005)
  • OGAWA Keiji ID: 9000365006254

    Articles in CiNii:1

    • 106 Fracture Strength of Laser Heat-Treated Ceramic Thin Film (2012)
  • OGAWA Keiji ID: 9000386210279

    Ryukoku University (2017 from CiNii)

    Articles in CiNii:1

    • Reproduction of Chasing Technology with Applied 6-axis Control Machining Center:(Investigation on Tool Approach & Retracts Motion in"KEBORI") (2017)
  • OGAWA Keiji ID: 9000387917063

    Department of Mechanical and Systems Engineering, Faculty of Science and Technology, Ryukoku Univesity (2018 from CiNii)

    Articles in CiNii:1

    • Development of Pure Bamboo Fiber Gear Made of Natural Fiber Material (2018)
  • OGAWA Keiji ID: 9000390887690

    Faculty of Science and Engineering, Ryukoku University (2017 from CiNii)

    Articles in CiNii:1

    • Laser Quenching and Forming Method for Thin Steel Plate under Preheating Conditions (2017)
Page Top