Search Results1-17 of  17

  • SATO Tatsushi ID: 9000000351708

    Insustrial Electronics & Systems Laboratory, Mitsubishi Electric Corporation (2000 from CiNii)

    Articles in CiNii:1

    • A New Grooving Method based on Steady Wear Model in EDM (2000)
  • SATO Tatsushi ID: 9000001474124

    三菱電機(株)先端技術総合研究所 (2005 from CiNii)

    Articles in CiNii:2

    • Entrance Mark Control on WEDM (2004)
    • Machining Control for Precision WEDM(<Special Issue>Novel Development of Electrical Discharge Machining) (2005)
  • SATO Tatsushi ID: 9000005408322

    Biemtron CO., LTD. (2007 from CiNii)

    Articles in CiNii:2

    • The spatial distribution measurement of the C_<60> fragmentation by employing ICP (2007)
    • 26aB19P Production of high-density fullerene plasma by using advanced fullerene oven-system (2003)
  • SATO Tatsushi ID: 9000017502311

    三菱電機(株) (2010 from CiNii)

    Articles in CiNii:22

    • Sensing a State of Machining with the Voltage Waveform in EDM (1995)
    • A New Grooving Method Based on Steady Wear Model in EDM (1997)
    • 電極消耗のモデル化の試み(第2報) -溝加工への拡張- (1996)
  • SATO Tatsushi ID: 9000021411048

    Advanced Technology R&D Center, Mitsubishi Electric Corporation (2008 from CiNii)

    Articles in CiNii:1

    • High-Speed Electrical Discharge Machining By Using a 5-DOF Controlled Maglev Local Actuator (2008)
  • SATO Tatsushi ID: 9000021594903

    三菱電機(株) (2011 from CiNii)

    Articles in CiNii:1

    • Hole Electrical Discharge Machining Using a High-Response and Multi-DOF Controlled Maglev Actuator (Effects of Direction, Amplitude and Frequency of Electrode Motion on Hole Machining Speed) (2011)
  • SATO Tatsushi ID: 9000254055424

    三菱電機 (株) 産業システム研究所 (1997 from CiNii)

    Articles in CiNii:1

    • A New Grooving Method Based on Steady Wear Model in EDM. (1997)
  • SATO Tatsushi ID: 9000292181767

    Mitsubishi Electric Corporation (2014 from CiNii)

    Articles in CiNii:1

    • Wire-break prevention on Wire Electrical Discharge Machining (2014)
  • SATO Tatsushi ID: 9000292181772

    Mitsubishi Electric Corporation (2014 from CiNii)

    Articles in CiNii:1

    • Wire Electrical Discharge Slicing of Solar-Grade Silicon (2014)
  • Sato Tatsushi ID: 9000003845388

    Articles in CiNii:2

    • 応力と固有振動数を制約とする2次元トラスの重量最小化問題--遺伝的アルゴリズム利用による球解法の検討 (2002)
    • Weight Minimization Problem of 2-Dimensional Trusses under Constraints of Stresses and Frequencies : Discussion on Solving Method by Using Genetic Algorithm (2000)
  • Sato Tatsushi ID: 9000258646649

    Mitsubishi Electric Corporation (2006 from CiNii)

    Articles in CiNii:1

    • Wire Electrical Discharge Machining on Semiconductive Material (2006)
  • Sato Tatsushi ID: 9000258652648

    三菱電機 (2010 from CiNii)

    Articles in CiNii:1

    • Maglev Actuator for Electrical Discharge Machining (5th Report):Effect of Amplitude and Frequency of Orbital Motion of Electrode on Hole Machining Speed (2010)
  • Sato Tatsushi ID: 9000258657352

    Mitsubishi Electric Corporation (2012 from CiNii)

    Articles in CiNii:1

    • The Electrical Discharge Machining for Silicon Carbide (2012)
  • Sato Tatsushi ID: 9000283813250

    Mitsubishi Electric Corp. (2007 from CiNii)

    Articles in CiNii:1

    • Study on Relationship between Machining shape and Input Energy in Wire-EDM (2007)
  • Sato Tatsushi ID: 9000283818514

    Mitsubishi Electric Corporation (2009 from CiNii)

    Articles in CiNii:1

    • 放電加工用磁気浮上アクチュエータの研究(第4報):穴加工における電極ジャンプ・加振効果の検討 (2009)
  • Sato Tatsushi ID: 9000283820473

    Mitsubishi Electric Corporation (2010 from CiNii)

    Articles in CiNii:1

    • A Compensation of Attachment Error of Rotary Electrode for Electrical Discharge Machining by using a Magnetic Bearing (2010)
  • Sato Tatsushi ID: 9000283820913

    Mitsubishi Electric Corporation (2011 from CiNii)

    Articles in CiNii:1

    • Hole Electrical Discharge Machining Using Runout Compensation of Rotary Electrode in a Magnetic Bearing (2011)
Page Top