Search Results1-20 of  64

  • 1 / 4
  • Yanagimoto Jun ID: 9000010304846

    Articles in CiNii:1

    • Semisolid extrusion of low-carbon steel (2007)
  • Yanagimoto Jun ID: 9000249502365

    Articles in CiNii:1

    • Microstructure of Cr-V-Mo Steel Processed by Recrystallization and Partial Melting and Its Effect on Mechanical Properties (2014)
  • YANAGIMOTO Jun ID: 9000000026965

    Institute of Industrial Science, The University of Tokyo (2012 from CiNii)

    Articles in CiNii:11

    • Finite-Element Analysis of Metal Flow in Bearing Section during Extrusion Process of Rectangular and Angle Sections - Combination of Three-Dimensional FE Simulation and Extrusion Die Design-1 - (1998)
    • Finite-Element Analysis of Metal Flow in Bearing Section during Extrusion Process of "L" "C" and "T" Sections - Combination of Three-Dimensional FE Simulation and Extrusion Die Design-2 - (1998)
    • Analytical and Experimental Investigations into Microstructure Evolution in Hot Bar Stretching (2001)
  • YANAGIMOTO Jun ID: 9000000101182

    Institute of Industrial Science, The University of Tokyo (1999 from CiNii)

    Articles in CiNii:1

    • Incremental Formulation for the Prediction of Microstructural Change in Multi-pass Hot Forming (1999)
  • YANAGIMOTO Jun ID: 9000000244809

    Institute of Industrial Science, The University of Tokyo (2000 from CiNii)

    Articles in CiNii:1

    • FE-based Analysis for the Microstructure Evolution in Hot Bar Rolling (2000)
  • YANAGIMOTO Jun ID: 9000000833991

    Institute of Industrial Science, The University of Tokyo (2002 from CiNii)

    Articles in CiNii:1

    • Effect of the Number of Work-roll Surface Division on Prediction of Contact Length in Coupled Analysis of Roll and Strip Deformation during Sheet Rolling (2002)
  • YANAGIMOTO Jun ID: 9000001119604

    Articles in CiNii:2

    • 東京大学生産技術研究所高次機能加工学研究分野 (2003)
    • Fundamental Investigation in Manufacturing Formable High-strength Steel Strips with Bimodal Microstructure by Width-restricted Heavy-reduction Controlled Rolling Process (2012)
  • YANAGIMOTO Jun ID: 9000001444821

    Institute of Industrial Science, The University of Tokyo (2003 from CiNii)

    Articles in CiNii:1

    • Mechanical Bonding Process to Manufacture Clad Materials-Divided Flow Bonding (2003)
  • YANAGIMOTO Jun ID: 9000001533818

    Institute of Industrial Science, The University of Tokyo (2005 from CiNii)

    Articles in CiNii:1

    • Regression Method of Determining Generalized Description of Flow Curve of Steel under Dynamic Recrystallization (2005)
  • YANAGIMOTO Jun ID: 9000001776365

    Institute of Industrial Science, The University of Tokyo (2006 from CiNii)

    Articles in CiNii:1

    • Finite Element Analysis of Tilting of Metal in Bar Rolled with Three-roll Mill (2006)
  • YANAGIMOTO Jun ID: 9000001850342

    Environmental Conscious Ultra-Fine-Grained Steel Consortium of JRCM (The Japan Research and Development Center of Metals) (2006 from CiNii)

    Articles in CiNii:1

    • Springback-free Isothermal Forming of High-strength Steel Sheets and Aluminum Alloy Sheets under Warm and Hot Forming Conditions (2006)
  • YANAGIMOTO Jun ID: 9000003797060

    東京大学 生産技術研究所 (2017 from CiNii)

    Articles in CiNii:20

    • The Change of Microstructure during continuous Rolling by 3-rolls Block Mill (2001)
    • 528 The Change of Austenite Microstructure during continuous Rolling by 3-rolls Block Mill (2000)
    • Reproduction of Minute Metal Scraps by Semisolid Processing (2009)
  • YANAGIMOTO Jun ID: 9000013905881

    東京大学 (2012 from CiNii)

    Articles in CiNii:8

    • 連載「21世紀の塑性加工に何が求められるか」I : 21世紀の塑性加工教育 (1992)
    • Requirement for the Technology Plasticity in the 21st Century IV : Computer and Technology of Plasticity in the 21st Century (1993)
    • 塑性加工FEMシミュレーション 21世紀への展望 (1994)
  • YANAGIMOTO Jun ID: 9000016395553

    Institute of Industrial Science, The University of Tokyo (2012 from CiNii)

    Articles in CiNii:2

    • Numerical Analysis for the Prediction of Microstructure after Hot Forming of Structural Metals (2009)
    • Changes in Mechanical Characteristics of Pre-Annealed Wires of Cu-Sn Alloy Manufactured by Continuous Draw Bending (2012)
  • YANAGIMOTO Jun ID: 9000017671723

    Institute of Industrial Science, The University of Tokyo (2002 from CiNii)

    Articles in CiNii:1

    • Three-dimensional Numerical Analysis of Microstructural Evolution in and after Bar and Shape Rolling Processes (2002)
  • YANAGIMOTO Jun ID: 9000017671820

    Institute of Industrial Science, The University of Tokyo (2002 from CiNii)

    Articles in CiNii:1

    • Continuous Heating System Using Electric Resistance Heating for the Hot Rolling of Stainless Steels (2002)
  • YANAGIMOTO Jun ID: 9000018186833

    Institute of Industrial Science, The University of Tokyo (2007 from CiNii)

    Articles in CiNii:1

    • Measurement of Ductile Forming Limit in Non-linear Strain Paths and Anisotropic Yield Conditions for 11% Cr Steel Sheets (2007)
  • YANAGIMOTO Jun ID: 9000018187189

    Institute of Industrial Science, The University of Tokyo (2007 from CiNii)

    Articles in CiNii:1

    • Ferrite Nucleation Kinetics inside Austenite Grain (2007)
  • YANAGIMOTO Jun ID: 9000019241001

    Institute of Industrial Science, The University of Tokyo (2012 from CiNii)

    Articles in CiNii:1

    • Multistage and High-speed Compression Testing Machine for Obtaining Flow Stress and Microstructure Evolution in Hot Forming of Steels (2012)
  • YANAGIMOTO Jun ID: 9000020609198

    The University of Tokyo (2009 from CiNii)

    Articles in CiNii:1

    • Solidification and Forming Technology of Minute Scrap Metal by Semisolid Process (2009)
  • 1 / 4
Page Top