粉末圧延法と放電焼結法を利用したステンレス網強化アルミニウム板の作製  [in Japanese] Preparation of stainless steel mesh reinforced aluminum sheets by powder rolling and spark sintering methods  [in Japanese]

Access this Article

Search this Article

Author(s)

Abstract

Aluminum matrix composite sheets, two-dimensionally reinforced with stainless steel mesh, were prepared by powder rolling and spark sintering. Tensile tests of the sintered samples were carried out to investigate the optimization of the preparing condition. Bonding of powder particles was promoted by sintering at higher temperature and for longer holding time. On the other hand, the intermetallic compound Al<sub>x</sub>(Fe, Ni, Cr) layer was produced at the interface between the stainless steel wire and aluminum matrix in the sintering process. The thickness of the intermetallic compound layer becomes larger at higher sintering temperature and for longer sintering time. Under the most suitable condition that the aluminum matrix is sintered enough and the thickness of the intermetallic compound layer is not so large, the maximum tensile strength of the composite is obtained. Under the conditions, the strength of the composite sheet increases and the elongation hardly changes with increasing volume fraction of stainless steel mesh to about 20%.

Journal

  • Journal of Japan Institute of Light Metals

    Journal of Japan Institute of Light Metals 52(5), 199-203, 2002-05-30

    The Japan Institute of Light Metals

References:  17

  • <no title>

    DUBE R. K.

    Inter. Mater. Reviews 35, 253, 1990

    Cited by (1)

  • <no title>

    SUZUKI Y.

    Powder Metallurgy 74, 1977

    Cited by (1)

  • <no title>

    STURGEON G. M.

    Sheet metal Industries January, 59, 1972

    Cited by (1)

  • <no title>

    面迫浩次

    日本鉄鋼協会講演大会概要 (CAMP-ISIJ) 4, 681, 1991

    Cited by (1)

  • <no title>

    魯雲

    広島大学大学院工学研究科博士学位論文, 1993

    Cited by (1)

  • <no title>

    師岡利政

    軽金属 37, 199, 1987

    Cited by (1)

  • <no title>

    浅沼博

    軽金属 40, 7, 1990

    Cited by (1)

  • <no title>

    小島陽

    軽金属 37, 220, 1987

    Cited by (1)

  • <no title>

    DUDEK H. J.

    Mater. Sci. Eng. A167, 129, 1993

    Cited by (1)

  • <no title>

    PAN J.

    J. Japan Inst. Metals 65, 199, 2001

    Cited by (1)

  • <no title>

    彦坂武夫

    軽金属 51, 86, 2001

    Cited by (1)

  • <no title>

    荒川進

    軽金属 50, 430, 2000

    Cited by (1)

  • <no title>

    奥村善雄

    軽金属 51, 157, 2001

    Cited by (1)

  • <no title>

    柳沢平

    まてりあ 33, 1489, 1994

    Cited by (11)

  • <no title>

    今井義一

    軽金属 40, 195, 1990

    Cited by (1)

  • <no title>

    伊藤義康

    材料 47, 665, 1998

    Cited by (4)

  • <no title>

    MOCHIZUKI C.

    Journal of Nuclear Material 271&272, 508, 1999

    Cited by (1)

Cited by:  1

  • 新素材  [in Japanese]

    前田 将克 , 小橋 眞 , 高野 直樹 , 梅本 実

    Journal of the Japan Welding Society 72(5), 358-362, 2003-07-05

    References (199)

Codes

  • NII Article ID (NAID)
    10008559271
  • NII NACSIS-CAT ID (NCID)
    AN00069773
  • Text Lang
    JPN
  • Article Type
    Journal Article
  • ISSN
    04515994
  • NDL Article ID
    6170296
  • NDL Source Classification
    ZP41(科学技術--金属工学・鉱山工学)
  • NDL Call No.
    Z17-284
  • Data Source
    CJP  CJPref  NDL  J-STAGE 
Page Top