Machining and Heat Treatment Effects on Distortion and Residual Stresses in an Industrial Application of ADI

この論文にアクセスする

この論文をさがす

著者

    • SOSA A. D.
    • Graduate Student, Mechanical Technology Research Group, National University of Mar del Plata (UNMDP)
    • MONCADA O. J.
    • Faculty of Engineering, National University of Mar del Plata (UNMDP)

抄録

The machining and heat treatment, employed in the fabrication of ADI parts, produce distortions and residual stresses that can increase the scrap rate. In the present study, dimensional changes, shape distortions and residual stresses due to machining and austempering were determined on internal gears of different chemical compositions, as-cast microstructures and machining-thermal cycle sequences. The influence of chemical composition and as-cast microstructure on dimensional change were found to be in accordance with the predictions obtained by Fuzzy modelling. Shape distortion resulted in an ovalization, whose magnitude depends upon the variation range of the residual stresses due to machining. Whereas residual stresses due to austempering were found to increase when the ovalization increases. <br>The lack of information about the topics here studied, turn these results into a useful contribution to improve the fabrication quality of ADI internal gears. Besides, most of them can be applied to ADI parts in general.

収録刊行物

  • ISIJ international

    ISIJ international 44(7), 1195-1200, 2004-07-15

    一般社団法人 日本鉄鋼協会

参考文献:  15件中 1-15件 を表示

  • <no title>

    KEOUGH J.

    Proc. of the 3rd World Conf. on ADI, 1991 II, 638, 1991

    被引用文献1件

  • <no title>

    MARTINEZ R.

    AFS Trans. 98, 28, 1998

    被引用文献1件

  • <no title>

    MONCADA O.

    Actas Congreso Internacional de Tecnologia Metalurgica y de Materiales 377, 1994

    被引用文献1件

  • <no title>

    ECHEVERRIA M.

    Actas CONAMET/SAM Simposio Materia 2002 I, 281, 2002

    被引用文献1件

  • <no title>

    SOSA A. D.

    Jornadas SAM-Conamet-AAS 475, 2001

    被引用文献1件

  • <no title>

    ECHEVERRIA M.

    ISIJ Int. 41, 25, 2001

    被引用文献1件

  • <no title>

    ECHEVERRIA M.

    Jornadas SAM 2000 IV, 405, 2000

    被引用文献1件

  • <no title>

    ECHEVERRIA M.

    Anales SAM '98-IBEROMET 287, 1998

    被引用文献1件

  • <no title>

    MONCADA O.

    Jornadas SAM '94 141, 1994

    被引用文献1件

  • <no title>

    ECHEVERRIA M.

    Jornadas SAM '2000 IV, 397, 2000

    被引用文献1件

  • <no title>

    A Dai Pra

    Jornadas SAM-Conamet-AAS 1041, 2001

    被引用文献1件

  • <no title>

    Metals Handbook

    Heat Treating 3, 1981

    被引用文献1件

  • <no title>

    Metals Handbook

    Machining 19, 1989

    被引用文献1件

  • <no title>

    MONCADA O. J.

    AFS Trans. 104, 577, 1996

    被引用文献2件

  • <no title>

    MONCADA O. J.

    AFS Trans. 106, 39, 1998

    被引用文献2件

各種コード

ページトップへ