Studies on automatic control of wood routing using acoustic emission アコースティック・エミッション信号を利用したルータ切削の自動制御に関する研究

Access this Article

Search this Article

Author

    • Cyra Grzegorz ツェラ グジェゴシュ

Bibliographic Information

Title

Studies on automatic control of wood routing using acoustic emission

Other Title

アコースティック・エミッション信号を利用したルータ切削の自動制御に関する研究

Author

Cyra Grzegorz

Author(Another name)

ツェラ グジェゴシュ

University

鳥取大学

Types of degree

博士 (農学)

Grant ID

甲第129号

Degree year

1997-09-26

Note and Description

博士論文

Table of Contents

  1. TABLE OF CONTENTS / p3 (0005.jp2)
  2. LIST OF TABLES / p6 (0008.jp2)
  3. LIST OF FIGURES / p7 (0009.jp2)
  4. INTRODUCTION / p1 (0013.jp2)
  5. REVIEW OF THE LITERATURE / p4 (0016.jp2)
  6. PART I. THE EFFECTS OF WOOD FIBER DIRECTIONS ON ACOUSTIC EMISSION / p11 (0023.jp2)
  7. 1.1 Introduction / p11 (0023.jp2)
  8. 1.2 Effect of grain angle / p12 (0024.jp2)
  9. 1.2.1 Experimental procedure / p12 (0024.jp2)
  10. 1.2.2 Results and discussion / p17 (0029.jp2)
  11. 1.3 Effect of annual ring angle / p28 (0040.jp2)
  12. 1.3.1 Experimental procedure / p28 (0040.jp2)
  13. 1.3.2 Results and discussion / p32 (0044.jp2)
  14. 1.4 Effect of slope angle / p35 (0047.jp2)
  15. 1.4.1 Experimental procedure / p35 (0047.jp2)
  16. 1.4.2 Results and discussion / p38 (0050.jp2)
  17. 1.5 Conclusions / p44 (0056.jp2)
  18. PART II. THE EFFECT OF ROUTER TOOL WEAR ON ACOUSTIC EMISSION / p47 (0059.jp2)
  19. 2.1 Introduction / p47 (0059.jp2)
  20. 2.2 Experimental procedure / p49 (0061.jp2)
  21. 2.2.1 Cutting conditions / p49 (0061.jp2)
  22. 2.2.2 AE measurements / p50 (0062.jp2)
  23. 2.2.3 Cutting forces measurements / p53 (0065.jp2)
  24. 2.2.4 Surface roughness measurements / p53 (0065.jp2)
  25. 2.2.5 Routing process analysis / p53 (0065.jp2)
  26. 2.3 Results and discussion / p54 (0066.jp2)
  27. 2.3.1 The effects of grain orientation and tool wear on AE signal / p54 (0066.jp2)
  28. 2.3.2 The effects of grain orientation and tool wear on cutting forces / p60 (0072.jp2)
  29. 2.3.3 The effects of grain orientation and tool wear on surface roughness / p60 (0072.jp2)
  30. 2.3.4 The effect of feed rate / p61 (0073.jp2)
  31. 2.3.5 AE versus edge recession / p67 (0079.jp2)
  32. 2.3.6 AE versus surface roughness / p67 (0079.jp2)
  33. 2.4 Conclusions / p68 (0080.jp2)
  34. PART III. ON-LINE CONTROL OF ROUTER FEED SPEED USING ACOUSTIC EMISSION / p70 (0082.jp2)
  35. 3.1 Introduction / p70 (0082.jp2)
  36. 3.2 Experimental Procedure / p71 (0083.jp2)
  37. 3.2.1 Adaptive control system / p71 (0083.jp2)
  38. 3.2.2 Experiment conditions / p75 (0087.jp2)
  39. 3.3 Results and discussion / p79 (0091.jp2)
  40. 3.4 The effect of the adaptive controller / p87 (0099.jp2)
  41. 3.4.1 Cutting along straight path (constant grain angle) / p87 (0099.jp2)
  42. 3.4.2 Cutting along circular arc (various grain angles) / p92 (0104.jp2)
  43. 3.5 Conclusions / p98 (0110.jp2)
  44. PART IV. SUMMARY AND CONCLUSION / p100 (0112.jp2)
  45. Summary / p100 (0112.jp2)
  46. Conclusions / p110 (0122.jp2)
  47. Bibliography / p112 (0124.jp2)
2access

Codes

  • NII Article ID (NAID)
    500000152527
  • NII Author ID (NRID)
    • 8000000152798
  • DOI(NDL)
  • NDLBibID
    • 000000316841
  • Source
    • NDL ONLINE
    • NDL Digital Collections

Export

Page Top