Formation mechanism of finished surface in ultra-high speed cutting 超高速切削における仕上面の生成機構

この論文をさがす

著者

    • Yousefi Reza ユセフイ レザ

書誌事項

タイトル

Formation mechanism of finished surface in ultra-high speed cutting

タイトル別名

超高速切削における仕上面の生成機構

著者名

Yousefi Reza

著者別名

ユセフイ レザ

学位授与大学

宇都宮大学

取得学位

博士 (工学)

学位授与番号

甲第93号

学位授与年月日

2000-03-24

注記・抄録

博士論文

目次

  1. CONTENTS / p1 (0003.jp2)
  2. CHAPTER1 / p1 (0006.jp2)
  3. INTRODUCTION / p1 (0006.jp2)
  4. 1.1 Definition of high-speed machining / p1 (0006.jp2)
  5. 1.2 High-speed machining advantages and limitations / p3 (0008.jp2)
  6. 1.3 High-speed machining applications / p4 (0009.jp2)
  7. 1.4 A review to other works / p5 (0010.jp2)
  8. 1.5 Aim of present work / p13 (0018.jp2)
  9. References / p13 (0018.jp2)
  10. CHAPTER2 / p16 (0021.jp2)
  11. POSSIBILITY OF ULTRA-HIGH SPEED MIRROR CUTTING / p16 (0021.jp2)
  12. 2.1 Introduction / p16 (0021.jp2)
  13. 2.2 Experimental procedure / p16 (0021.jp2)
  14. 2.3 Results and discussion / p21 (0026.jp2)
  15. 2.4 Conclusions / p32 (0037.jp2)
  16. References / p33 (0038.jp2)
  17. CHAPTER3 / p34 (0039.jp2)
  18. MATERIAL FACTOR IN ULTRA-HIGH SPEED MIRROR CUTTING / p34 (0039.jp2)
  19. 3.1 Introduction / p34 (0039.jp2)
  20. 3.2 Experimental method for oxygen-free copper / p34 (0039.jp2)
  21. 3.3 Results and discussion for oxygen-free copper / p35 (0040.jp2)
  22. 3.4 Experimental conditions for aluminum alloy / p52 (0057.jp2)
  23. 3.5 Results and discussions for aluminum alloy / p52 (0057.jp2)
  24. 3.6 Comparison between finished surfaces of two materials / p61 (0066.jp2)
  25. 3.7 Conclusions / p63 (0068.jp2)
  26. References / p64 (0069.jp2)
  27. CHAPTER4 / p66 (0071.jp2)
  28. TOOL WEAR FACTOR IN ULTRA-HIGH SPEED MIRROR CUTTING / p66 (0071.jp2)
  29. 4.1 Introduction / p66 (0071.jp2)
  30. 4.2 Experimental method / p66 (0071.jp2)
  31. 4.3 Results and discussion / p67 (0072.jp2)
  32. 4.4 Conclusion / p74 (0079.jp2)
  33. References / p75 (0080.jp2)
  34. CHAPTER5 / p76 (0081.jp2)
  35. ULTRA-HIGH SPEED FINISHING PROCESS FOR ALUMINUM ALLOY / p76 (0081.jp2)
  36. 5.1 Introduction / p76 (0081.jp2)
  37. 5.2 Experimental method / p76 (0081.jp2)
  38. 5.3 Results and discussion / p78 (0083.jp2)
  39. 5.4 Conclusions / p87 (0092.jp2)
  40. References / p87 (0092.jp2)
  41. CHAPTER6 / p89 (0094.jp2)
  42. ULTRA-HIGH SPEED FINISHING PROCESS FOR MILD STEEL ALLOY / p89 (0094.jp2)
  43. 6.1 Introduction / p89 (0094.jp2)
  44. 6.2 Experimental method / p89 (0094.jp2)
  45. 6.3 Results and discussion / p92 (0097.jp2)
  46. 6.4 Conclusions / p101 (0105.jp2)
  47. References / p102 (0106.jp2)
  48. CHAPTER7 / p103 (0107.jp2)
  49. MIRROR CUTTING OF SINGLE CRYSTAL SILICON / p103 (0107.jp2)
  50. 7.1 Introduction / p103 (0107.jp2)
  51. 7.2 Experimental procedure / p103 (0107.jp2)
  52. 7.3 Results and discussion / p105 (0109.jp2)
  53. 7.4 Conclusions / p112 (0116.jp2)
  54. References / p112 (0116.jp2)
  55. CHAPTER8 / p113 (0117.jp2)
  56. General conclusions / p113 (0117.jp2)
  57. Acknowledgement / p118 (0122.jp2)
  58. APPENDIX / (0123.jp2)
  59. EXPERIMENT DESIGN / (0123.jp2)
  60. A.1 Introduction / p119 (0123.jp2)
  61. A.2 Machine tool / p120 (0124.jp2)
  62. A.3 Workpiece and work holder design / p130 (0134.jp2)
  63. A.4 Tool post design / p133 (0137.jp2)
  64. A.5 Supplementary devices / p135 (0139.jp2)
  65. A.6 Balancing / p138 (0142.jp2)
  66. References / p139 (0143.jp2)
0アクセス

各種コード

  • NII論文ID(NAID)
    500000187223
  • NII著者ID(NRID)
    • 8000000187506
  • DOI(NDL)
  • NDL書誌ID
    • 000000351537
  • データ提供元
    • NDL ONLINE
    • NDLデジタルコレクション
ページトップへ