Research on integration of CAD/CAM system for low-repetitive machining center work 小繰返しマシニングセンター加工のCAD/CAM統合の研究
この論文にアクセスする
この論文をさがす
著者
書誌事項
- タイトル
-
Research on integration of CAD/CAM system for low-repetitive machining center work
- タイトル別名
-
小繰返しマシニングセンター加工のCAD/CAM統合の研究
- 著者名
-
Shakeri Mohsen
- 著者別名
-
シャケリ モーセン
- 学位授与大学
-
豊橋技術科学大学
- 取得学位
-
博士 (工学)
- 学位授与番号
-
甲第244号
- 学位授与年月日
-
2000-03-22
注記・抄録
博士論文
目次
- Table of contents / p1 (0005.jp2)
- Japanese Abstract / (0003.jp2)
- English Abstract / p1 (0004.jp2)
- Chapter I Introduction / p1 (0009.jp2)
- 1.1 Background of research / p1 (0009.jp2)
- 1.2 Objective of the research / p6 (0012.jp2)
- 1.3 Methods of the research / p7 (0012.jp2)
- 1.4 References / p9 (0013.jp2)
- Chapter II Automatic Feature recognition from 2D Engineering Drawing / p10 (0014.jp2)
- 2.1 Introduction / p10 (0014.jp2)
- 2.2 Short review of related works / p12 (0015.jp2)
- 2.3 Approach of the present study / p13 (0016.jp2)
- 2.4 Outline of the feature recognition principle / p14 (0016.jp2)
- 2.5 Pre-processing / p15 (0017.jp2)
- 2.6 2D-Loop extraction / p19 (0019.jp2)
- 2.7 Complex loop conversion / p21 (0020.jp2)
- 2.8 Feature identification / p23 (0021.jp2)
- 2.9 Drafting database and analyzer / p26 (0022.jp2)
- 2.10 Software system configuration / p27 (0023.jp2)
- 2.11 Practical issues / p30 (0024.jp2)
- 2.12 Example / p32 (0025.jp2)
- 2.13 Implementation of software system / p34 (0026.jp2)
- 2.14 Conclusion / p40 (0029.jp2)
- 2.15 References / p42 (0030.jp2)
- Chapter III An integrated representation for CAD/CAM system / p43 (0031.jp2)
- 3.1 Introduction / p43 (0031.jp2)
- 3.2 Outline of CAD procedures / p45 (0032.jp2)
- 3.3 Fully automated CAM processing / p55 (0037.jp2)
- 3.4 Example machined parts / p73 (0046.jp2)
- 3.5 Conclusion / p74 (0047.jp2)
- 3.6 References / p76 (0048.jp2)
- Chapter IV Standard fixture design concept for upstream integration in CAD/CAM system / p77 (0048.jp2)
- 4.1 Introduction / p77 (0048.jp2)
- 4.2 Basic engineering requirement for fixture preparation / p78 (0049.jp2)
- 4.3 New concept for fixture design / p79 (0049.jp2)
- 4.4 Realization of new concept / p83 (0051.jp2)
- 4.5 Referencing capability of CAM system for achieving fully external setup / p89 (0054.jp2)
- 4.6 Example of machined parts / p91 (0055.jp2)
- 4.7 Conclusion / p92 (0056.jp2)
- 4.8 References / p93 (0056.jp2)
- Chapter V General conclusions of the research / p94 (0057.jp2)
- 5.1 Objective of the study / p94 (0057.jp2)
- 5.2 Methods of the research / p95 (0058.jp2)
- 5.3 Results of the study / p95 (0058.jp2)
- 5.4 Concluding remarks and suggested tasks for future study / p97 (0059.jp2)
- Acknowledgments / p1 (0059.jp2)
- Appendix:List of publications / p1 (0060.jp2)