Structural adhesive joints in engineering
著者
書誌事項
Structural adhesive joints in engineering
Elsevier Applied Science, c1984
大学図書館所蔵 全23件
  青森
  岩手
  宮城
  秋田
  山形
  福島
  茨城
  栃木
  群馬
  埼玉
  千葉
  東京
  神奈川
  新潟
  富山
  石川
  福井
  山梨
  長野
  岐阜
  静岡
  愛知
  三重
  滋賀
  京都
  大阪
  兵庫
  奈良
  和歌山
  鳥取
  島根
  岡山
  広島
  山口
  徳島
  香川
  愛媛
  高知
  福岡
  佐賀
  長崎
  熊本
  大分
  宮崎
  鹿児島
  沖縄
  韓国
  中国
  タイ
  イギリス
  ドイツ
  スイス
  フランス
  ベルギー
  オランダ
  スウェーデン
  ノルウェー
  アメリカ
注記
Includes bibliographical references (p.283-291) and index
内容説明・目次
内容説明
The intention of this book is that it should contain everything an engineer needs to know to be able to design and produce adhesively bonded joints which are required to carry significant loads. The advan- tages and disadvantages of bonding are given, together with a sufficient understanding of the necessary mechanics and chemistry to enable the designer to make a sound engineering judgement in any particular case. The stresses in joints are discussed extensively so that the engineer can get sufficient philosophy or feel for them, or can delve more deeply into the mathematics to obtain quantitative solutions even with elasto- plastic behaviour. A critical description is given of standard methods of testing adhesives, both destructively and non-destructively. The essen- tial chemistry of adhesives and the importance of surface preparation are described and guidance is given for adhesive selection by me ans of check lists. For many applications, there will not be a unique adhesive which alone is suitable, and factors such as cost, convenience, produc- tion considerations or familiarity may be decisive. A list of applications is given as examples.
The authors wish to increase the confidence of engineers using adhesive bonding in load-bearing applications by the information and experience presented. With increasing experience of adhesives en- gineering, design will become more elegant as weH as more fitted to its products.
目次
1. Introduction.- Joint Configurations: Lap-shear Joints, Butt Joints, Fillets. Metals and Other Constructional Materials. The Decision to Use Adhesive Bonding. The Balance of Advantages and Disadvantages.- 2. The Nature And Magnitude of Stresses In Adhesive Joints.- Introduction: Reality, Methods of Mathematical Analysis. The Single Lap Joint: Linear Elastic Analysis, Volkersen's Analysis, The Analysis of Goland and Reissner, Effect of Bending in a Double-lap Joint, Volkersen's Second Theory, Later Work. The Single-lap Joint - End Effects: Reduction of Stress Concentrations. The Single-lap Joint - Elasto-plastic Analysis. The Effect of Adherend Shape - Scarfed, Bevelled and Stepped Adherends. Composite Materials. Tubular Joints. Butt Joints. The Use of Joints in Design: Lap Joints, Tubular Joints, T-joints, Corner Joints, Butt Joints, Stiffeners, Doublers, Assembly.- 3. Standard Mechanical Test Procedures.- Destructive Testing: Tests with Thin Sheet Adherends, Tests for Properties of Adhesives. Nondestructive Testing: Nature of Defects, Tests Carried Out Before Bonding, Post-bonding and In-service Testing.- 4. The General Properties of Polymeric Adhesives.- Polymer Structures: Unsaturation. Mixed Adhesives. Properties and Temperature: The Glass Transition Temperature, Decomposition Temperature, Melting Temperature, The Deformation of Adhesive Polymers by Stress, Viscoelasticity, The Modulus of an Adhesive, Poisson's Ratio, Strength Properties of Adhesive Polymers, Yielding Stresses of Polymers, Failure Modes After Yielding, Creep, Failure without Yielding - Brittle Fracture, Crazing, Coefficient of Thermal Expansion, Resistance to Deterioration.- 5. Factors Influencing The Choice of Adhesive.- Interaction with Substrate. Structural Adhesives for Metals: Check-list for Structural Metal Adhesives Used at Temperatures up to 70 C, The Advantage of Supported Filmic Adhesives (Tapes'), Unsupported Films, Liquids and Pastes, Influence of Metal of Adherend, High Temperature Metal-Metal Adhesion. Structural Adhesives for Wood: Check-list for the Use of Structural Wood Adhesives. Structural Adhesives for Mixed Constructions: Metal-Wood Structures, Metal-reinforced Plastics Structures. Choice of Adhesives for Semi-structural Use: Checklist for Adhesives for Semi-structural Use.- 6. Surface Preparation.- Metals. Wood. Concrete. Glass or Carbon-fibre Reinforced Plastics. Shot, Sand or Grit Blasting. Solvent Degreasing or Wiping. Chemical Etching: Aluminium, Ferrous Metals, Titanium, Other Metals. Priming Layers: Primers as Coupling Agents.- 7. Service Life.- The Creep of Adhesive Joints. Time-to-failure (Under Static Loading). Cycles-to-failure: Influence of Temperature, Influence of Test Frequency, Influence of Amplitude, Influence of Moisture. Effects of Temperature Change on Joint Strength. Service Life as Indicated by Climatic Exposure Trials.- 8. Applications.- Aircraft, Anchorages. Bridges. Carriages. Cars. Decking. Furniture. Glass Reinforced Plastics. Helicopters. Helicopter Blades. Hovercraft. Lamp Posts. Magnets. PABST. Rollers. Segmental Construction. Ski Constructions. Telephone Kiosks. Yachts.- References.- Appendix: Standard American and UK Specifications for.- Adhesion Tests.- Author Index.
「Nielsen BookData」 より