Engineering in process metallurgy
著者
書誌事項
Engineering in process metallurgy
(Oxford science publications)
Clarendon Press, 1992
- : pbk
大学図書館所蔵 全4件
  青森
  岩手
  宮城
  秋田
  山形
  福島
  茨城
  栃木
  群馬
  埼玉
  千葉
  東京
  神奈川
  新潟
  富山
  石川
  福井
  山梨
  長野
  岐阜
  静岡
  愛知
  三重
  滋賀
  京都
  大阪
  兵庫
  奈良
  和歌山
  鳥取
  島根
  岡山
  広島
  山口
  徳島
  香川
  愛媛
  高知
  福岡
  佐賀
  長崎
  熊本
  大分
  宮崎
  鹿児島
  沖縄
  韓国
  中国
  タイ
  イギリス
  ドイツ
  スイス
  フランス
  ベルギー
  オランダ
  スウェーデン
  ノルウェー
  アメリカ
内容説明・目次
- 巻冊次
-
ISBN 9780198562221
内容説明
This text on process engineering in metallurgy, introduces the basic mechanisms of heat, mass and fluid flow, and shows the origin of associated transport coefficients (diffusivity, conductivity, and viscosity). Chapters dealing with fluid flow, heat and mass diffusion, and heat and mass convective flows then follow by way of a series of metallurgical examples and exercises. Empirical techniques for modelling and for process design are presented, followed by numerical techniques and computer programs needed for "ground-up" quantitive descriptions of typical metallurgical processes. An appendix provides detail on the thermodynamic and physical properties of substances commonly encountered by metallurgists, while a short section on metallurgical thermodynamics illustrates the way these tabulations are intended to be used.
目次
- Part 1 An introduction to transport phenomena and properties in metallurgical operations: including Newton's second law of motion
- Newton's law of viscosity
- the Chapman-Enskog equation. Part 2 Fluid statics and fluid dynamics: including Navien-Stokes equation
- flow past spheres at high Reynold's numbers
- Prandtl's theory of turbulence for boundary layers
- the Euler (momentum) and Bernoulli equations for inviscid fluids. Part 3 Dimensional analysis and reactor design: including Rayleigh's method of indices
- Buckingham's "pi" theorem. Part 4 Heat and mass transfer through motionless media: including the "exact" form of Fick's law of diffusion
- high and low Biot numbers. Part 5 Heat and mass transfer in convective flow systems: including the Lewis-Whitman two-film theory
- Danckwerts' surface renewal theory. Part 6 Numerical techniques and computer applications: including the Gauss-Siedel point-by-point method. Further reading. Appendices: 1 - nomenclature
- 2 - units, dimensions and conversion factors
- 3 - thermodynamic data, worked examples, physical properties, periodic table, error function. Tables. Index. References.
- 巻冊次
-
: pbk ISBN 9780198563679
内容説明
A rich variety of phenomena governs the behaviour and kinetics of metallurgical processing operations. Unusually high operating temperatures, intense radiation, viscous slags, dense metals, etc., make the design and operation of metallurgical processes unique.
This book introduces the basic mechanisms of heat, mass, and fluid flow, and then follows a series of metallurgical examples and exercises. Empirical techniques for modelling and for process design are presented along with numerical techniques and computer programs. This new paperback edition has been updated, with a new section on numerical simulation of fluid flow processes added, to reflect the important contribution of computer simulation to the subject.
目次
- An introduction to transport phenomena and properties in metallurgical operations
- Fluid statics and fluid dynamics
- Dimensional analysis and reactor design
- Heat and mass transfer through motionless media
- Heat and mass transfer in convective flow systems
- Numerical techniques and computer applications.
「Nielsen BookData」 より