Designing, processing and properties of advanced engineering materials : proceedings of the 3rd International Symposium on Designing, Processing and Properties of Advanced Engineering Materials, held in Jeju, Korea, November 5-8, 2003

著者

• International Symposium on Designing, Processing and Properties of Advanced Engineering Materials
• Kang, S.-G.
• 小林, 俊郎 コバヤシ, トシロウ

書誌事項

Designing, processing and properties of advanced engineering materials : proceedings of the 3rd International Symposium on Designing, Processing and Properties of Advanced Engineering Materials, held in Jeju, Korea, November 5-8, 2003

edited by S.-G. Kang and T. Kobayashi

（Materials science forum, 449-452）

Trans Tech, c2004

• v. 1
• v. 2

タイトル別名

ISAEM-2003

注記

Includes bibliographical references and index

内容説明・目次

内容説明

Volume is indexed by Thomson Reuters CPCI-S (WoS). Following on the success of the last previous two symposiums, the aim of ISAEM-2003 is was to provide an interactive forum for discussion of the designing, processing and properties of advanced engineering materials of involving metals, ceramics and polymers.

目次

• Asymmetric Rolling as Means of Texture and Ridging Control and Grain Refinement of Aluminum Alloy and Steel Sheets High Performance Materials Development in the 21st Century: Trends and Directions Toughness Assessment of a Variety of Materials: Similarities and Discrepancies Modeling Precipitate Microstructure Evolution in Alloys with First-Principles Energetic Information Processing and Alloy Development to Optimise the Properties and Cost-Effectiveness of Components Manufactured from TiAl-Based Alloys Orientation Dependence of Dynamic Recrystallization Behavior of Al Single Crystals Recent Progress in Molecular Orbital Approach to Alloy Design Aerosol Deposition Method for Fabrication of Nano Crystal Ceramic Layer Quantitative Analysis of Precipitation Behavior in Ferrite of V Added Microalloyed Steel Characterization of Friction Welding for IN713LC and AISI 4140 Steel High Temperature Deformation Mechanism Maps of NiAl Metastable Two-Phase Field(A2+B2) in Co-Al-Fe and Co-Al Alloy Systems Fabrication of Magnesium Alloy (AZ31) Sheet by Extrusion Development of Modified Embedded Atom Method for Alkali Metals Design and Fabrication of Bi-Convex Variable Focusing Lens Arrays Using Liquid Crystal for Integral Photography Characteristics of Electron Density Distributions in Metal Oxides High Temperature Wear Properties of Multiphase Composite: The Role of Transfer Film Properties Evaluation of Composites Including Cracked Ellipsoidal Inhomogeneity Molecular Dynamics Simulation of Stress Induced Grain Boundary Migration during Nanoindentation Experiments Influence of Biaxial Surface Stress on Mechanical Indenting Deformations Molecular Dynamics Analysis of Structure and Intrinsic Stress in Amorphous Silicon Carbide Film with Deposition Process Parameters Numerical Analysis on the Dissimilar Channel Angular Pressing by Multi-Pass Rolling A Study on the Process Design of Cold-Forged Automobile Parts Finite Element Method in Powdered Metal Compaction Processes Modification of the Recrystallization Texture by Means of Cross Rolling in Ferritic Stainless Steel Sheets Creep Analysis of Cr-Mo Steels Using a Dislocation Based Constitutive Modelling Effects of Processing Variables on the Development of the Cube Texture in Ni Tapes Fabricated by the Cold Working of Ni Powder Compact Rods A New Control Algorithm for Impressed Current Cathodic Protection on the Underwater Hull Study of Magnetic Annealing on Magnetostriction in Grain-Oriented 3.2 % Si Steels Effect of Heating Rate on Transient Liquid Phase Diffusion Bonding of Ni-Based Superalloy GTD-111 Notch Effects on Impact Tensile Properties in A6061-T6 Aluminum Alloy Ultrafine Grained Bulk 5083 Al Alloy Produced by Cryogenic Rolling Process Aluminum Alloy Strips Casting Using an Unequal Diameter Twin Roll Caster Development of Light-Weight Al Scroll Compressor for Car Air Conditioner Effect of Bubbling on the Primary Silicon in Hypereutectic Al-Si Alloy Effect of Electromagnetic Force on the Silicon Size in Hypoeutectic Al-Si Alloy Effect of Stacking Layer Number on Mechanical Properties of Accumulative Roll Bonding Processed Aluminum Enhanced Modification Process of B.390 Casting Alloy by the Ca Content Control Microstructure Characterizations of Hypereutectic Al-Si Alloys with Different Undercooling Levels Effect of Distribution Coefficient on Copper Purification by Zone Refining Process Grain Refinement of Copper Alloys by Equal Channel Angular Pressing Formability of Magnesium Alloy Sheets Manufactured by Semi-Solid Roll Strip Casting Transformation Behavior of a Ti-Ni-Cu-Fe Alloy Prediction of Microstructure During High Temperature Forming of Ti-6Al-4V Alloy Dissimilar Joining of Nickel Aluminide Intermetallic Compound with Spheroidal Graphite Cast Iron by Using Combustion Synthesis Surface Amorphization in Intermetallic Compounds by Shot Peening Combustion Synthesis Process of Ag Added Al3Ti Intermetallic Compound Morphology of Carbon Micro-Coils Synthesis of Porous Mullite by Vapor Phase Reaction Self-Propagating High-Temperature Synthesis of Aluminum Nitride and its Characterization Fabrication of Activated Carbon Fibers from Stabilized PAN-Based Fibers by KOH Role of Unstable Chemical Species (Non-Graphitic Carbon and Flowing NH3 Gas) on the Equilibrium Point of the Reaction Product (Carbide, Carbo-Nitride or Nitride) Sinter-Bonding of Polycrystalline Silicon-Nitride Using Source Powder of Superplastic Ceramics as Insert Material Processing Technique for Wear Resistance Parts Using Ultra Fine Particles Reinforced Si3N4 Preparation and Characterization of Porous Si-Coated SiC Fiber Media Abnormal Crystal Growth in the Sintered (Bi0.2Sb0.8)2Te3 Alloys Induced by Silver Addition Efflorescence and Leaching Behavior of Metal Ions for EAF Dust-Clay Based Bricks Production Mechanism of Superfine Powders by Jet Mill Synthesis and Evaluations of Microstructure Properties on Al-(50, 60, 70 mass%)Si Systems by Mechanical Alloying Nanocomposite Formation in the Fe2O3-M (M=Al, Ti, Zn, Cu) Systems by Mechanical Alloying Mechanical Alloying Effect of Hematite and Graphite Sintering Distortion of Barrier Ribs Formed via Capillary Molding Effect of CoO Doping on the Sintering Ability and Mechanical Properties of Y-TZP Serration Phenomenon in High Purity Chromium Synthesis of CuInSe2 and CuInGaSe2 Nanoparticles by Solvothermal Route Recovery of Lithium from Seawater Using Nano-Manganese Oxide Adsorbents Prepared by Gel Process Resistance Sintering of Copper-Graphite Powder Mixture under Pressure Fabrication of Thin Film Using Nanosized Indium Tin Oxide (ITO) Powder and Its Degradation Characteristics Photocatalysis for Oxidation of Phenol and Reduction of Inorganic Pollutants by Nanocrystalline TiO2-ZrO2 Powders Fabrication of Al2O3-ZrO2 (3Y-TZP) Composites with Graded Structures by Centrifugal Slip Casting Method Fabrication and Properties of TiB2 Reinforced Cu Composites by Electromagnetic Stirring Fabrication of BN/Al(-Mg) Metal Matrix Composite (MMC) by Pressureless Infiltration Technique Tensile Properties and Fracture Behavior of SiCp/AC4CH Composite at Loading Velocities of up to 10m/s Preparation of W-C-B Composites by Reactive Resistance-Heated Hot Pressing Measurement and Analysis of Plasma Arc Cutting Acoustic Signal Fabrication of Copper Clad Aluminum Wire (CCAW) by Indirect Extrusion and Drawing Microstructural Effects of Electromagnetic Stirring Strength and Casting Speed in Continuous Casting of Al Alloy Barrier Ribs of PDP by Injection Molding Analysis of Waste Heat Recovery to Steel Scrap Preheating in an Enclosure Vessel Up-Grade Recycle by Consolidating Aluminum Cutting Chip under Severe Plastic Deformation Low-Cycle Fatigue Fracture Behavior of Superalloy GH4586 at Elevated Temperature Effects of Deformation on Surface Modification by Nitrogen Ion-Implantation Improvement of Inner Surface for Machine Parts by Shot Peening Oxidation Behaviour of Nickel-Based Alloys Containing High Re Contents Comparable to the Third Generation Nickel-Based Superalloys Plasma Etching for Fabricating the Concave-Type DRAM Capacitors Vertical Etching of Ru Electrodes Using the O2/Cl2 System Dry Oxidation Behavior of Epitaxial Si0.7Ge0.3 Films Crystal Growth of Aluminum Magnesium Borides from Al-Mg-B Ternary System Solutions and Properties of the Crystals Corrosion Characteristics of Surface-Modified DET Magnesium Powders Plasma Characteristics of Supersonic Nitrogen/Hydrogen-Mixture and Ammonia Plasma Jets and Nitrided Material Properties Electrodeposition of Bi2Te3 for Nanowire Application Fabrication of Si Nitride Coating onto Metal Substrate by Reactive RF Plasma Spraying Characteristics of the Compound Layer on the SCM 435 Steel Produced by Plasma Nitrocarburizing Material Spraying Using Electromagnetically Accelerated Plasma Jet Electrochemical Kinetics Study of Electroless Copper Plating for Electronics Application Property of Laser Welded Bake-Hardening Steel in Tailored Blanks for Automobile Reaction between Sn-In Solder and Under Bump Metallurgy A Study on Interfacial Reaction between Electroless Plated Ni-P/Au UBM and Sn-Bi Eutectic Solder Using AEM Characteristics of CO2 Laser Welded 800MPa Grade TRIP Steel Explosive Welding of Thin Plates Using Underwater Shock Wave for Surface Modification Welding of AZ31B Magnesium Alloy by YAG Laser/ TIG Arc Hybrid Welding Process Observation of Metal Flow Phenomenon of Lap Joints during Friction Stir Welding Topics on Recent Friction Stir Welding Developments in Japan Spectroscopic Analysis of Plasma Induced in Laser Welding of Aluminum Alloys Welding of Aluminum and Steel by Friction Stir Diffusion Process Friction Welding of A 6061 Aluminum Alloy and S45C Carbon Steel Cu-Based Metallic Glass Matrix Composites with High Ductility Scanning Electron Microscopy Observations of Fractal Pattern Formation in Al/Ge Bilayer Films Fabrication of CdS Thin Film Pattern by CBD Method Using the Self-Assembled Monolayer Dependence of Titanium Deposition upon Its Ionic State in Molten Salt Deposition of Copper Thin Films on Titanium Nitride Layer Prepared by Flow Modulation CVD Technology Development of Ultra Fine Crystalline Diamond Film and Some Applications Microstructure and Chemical Properties of c-BN Films Prepared by ME-ARE Preparation and Characterization of IZO Transparent Conducting Films by the Sol-Gel Method Effect of UV Illumination on Deposition of Low-k Si-O-C(-H) Films by PECVD Ferroelectric Characteristics of SrxBi2.4Ta2O9 Thin Films and Electrical Properties of the Pt/SrxBi2.4Ta2O9/TiO2/Si Structure Observation of Crystallization Behavior in ITO Thin Films Prepared by RF-Magnetron Sputtering with and without External Heating Hydrogen-Induced Degradation and Passivation of Ferroelectric SrBi2Ta2O9 Thin Films by Au Top Electrode Oriented Growth of ZnO Thin Films on SiC Buffered Si(001) Substrates by Pulsed Laser Deposition Epitaxial Growth of Mn-Doped ZnO Thin Films on Al2O3 (0001) Characteristics of ZrO2/Al2O3 Bilayer Film for Gate Dielectric Applications Deposited by Atomic Layer Deposition Method Effect of Binders on the Magnetic Behavior of P/M Processed FeSiBCuNb Alloy Axial Pressing Method Using Pulse Magnetizing Field for the Preparation of Nd-Fe-B Sintered Magnets Effect of Growth Condition on the Electrical and Magnetic Properties of Sputtered ZnCo2O4 Films Alternating Magnetic Field Crystallization of Amorphous Si Films Effects of Pre-Strain and Aging Treatment on the Mechanical Properties of 1.0wt.%Cu Containing Hot Rolled Steel Sheet Coarsening Kinetics of B2 Precipitate Particles in an Elastically Constrained Fe-Al-Co Alloy Microstructural Change of Cementite in Carbon Steels by Deformation TEM Observations of the Precipitation of A2 Particles in D03 Precipitates in Fe-Si-V Alloy System Effects of Heat Treatment and Alloying of Spheroidal Graphite Cast Iron on Corrosion Resistance in Aqueous Environment Characteristics of Material Degradation for Thermal Aged X20CrMoV12 1 Steel Mechanical Behavior of As-Cast and High Temperature Exposed Ni-Base Superalloy B1900 Investigation on -Channel Widening during Uniaxial Creep Test of a Ni-Base Single Crystal Superalloy Tensile Deformation Behavior of M963 Cast Nickel-Base Superalloy Effect of Melt Treatment on the Microstructure and Creep-Rupture Behavior of M963 Cast Nickel-Base Superalloy Tensile Deformation Behavior of M963 Cast Nickel-Base Superalloy Low Cycle Fatigue and Fracture Behavior of Nickel-Base Superalloy CM247LC at 760 DegreesC Texture of Electrodeposited Ni Films Ultrasonic Nondestructive Evaluation of the Creep Damaged IN738LC Superalloy Mechanical Property of Single Phase Co-Ni-Cr-Mo Based Superalloy Produced by Cold Working and Recrystallization Heat Treatment Critical Strain for the Initiation of Dynamic Recrystallization in a Ni-Fe Base Alloy Thermomechanical Behavior of Al-Mg-Si Alloys at the Elevated Temperature Effects of Silicon and Chromium on the SCC Properties of Al-Zn-Mg-Cu Cast Alloy Tensile Deformation and Fracture Behavior of a Commercial Al Alloy with Nano-Sized Grains In-Situ Orientation Rotation Behavior Study during Tensile Deformation of Aluminum Single Crystal and Polycrystal Dry Sliding Wear Characteristics of Severely Deformed 6061 Aluminum and AZ61 Magnesium Alloys Effect of PWHT on Behaviors of Precipitates and Hardness Distribution of 6061 Al Alloy Joints by Friction Stir Welding Method Rapid Grain Growth of Hot Extruded Al-Zn-Mg-Cu-(Sc) Alloy during Heat Treatment Spray Casting of Al-25Si Alloy and Hot Deformation Behavior Ultra Grain Refinement and High Strengthening of Al Based MMC by Accumulative Roll Bonding Process Effects of Silicon and Chromium on the Fatigue Properties of Al-Zn-Mg-Cu Cast Alloy Thermal Properties and Fracture Behavior of Compositionally Graded Al-SiCp Composites Microstructural Evolution and Mechanical Properties of Ultrafine Grained Commercially Pure 1100 Aluminum Alloy Processed by Accumulative Roll-Bonding (ARB) Wear Behavior of Graphite-Dispersed Al-Sn-Si Alloys A Study on Tactile Friction and Wear - Frictional Wears Characteristics of Human Fingers on Various Soft Materials Model for the Protective Oxidation of Mg-Ca Alloys Containing Be at Elevated Temperature Effect of Sb Addition on the Creep Property of AZ31 Alloy Tensile Deformation Characteristics of Commercial Mg Alloys Processed by Equal Channel Angular Pressing Precipitation Behavior of Mg-Y-Nd-Zr Alloy Mechanical and Fracture Behaviors of (Al2O3+SiCp)/AZ91 Hybrid Mg Matrix Composite Damping and Mechanical Properties of (Graphite + 9Al2O3*2B2O3)/Mg Metal Matrix Composites Measurement and Analysis of Sound Absorption of Porous Magnesium Dislocation Plasticity and Complementary Deformation Mechanisms in Polycrystalline Mg Alloys Grain Refinement on AZ31 Magnesium Alloy by Highly Strained and Annealed Method Anelastic Properties of Polycrystalline Copper Microstructure and Mechanical Properties of DBC on Sputter Deposited Copper on Alumina Substrate Characteristics of the Electroless-Deposited Cu Film as Interconnect on a TaN Diffusion Barrier Microstructures and Electrical Conductivity of Cu-Ca Alloys for High Efficiency Induction Motors Tensile Properties of Cast and Hot Isostatic Pressurized Ti-6Al-4Fe-xSi Alloys Fatigue and Contact Damage of Layered Machinable Ti3SiC2 Ceramics Effect of Annealing on the Microstructures and Mechanical Properties of Mo3Si-Mo5Si3 Eutectic Direct Growth of SiC Nanorods on Si Using APCVD and Single Precursors In-Situ Fabrication and Microstructure of Alumina-Zirconia Layered Rolling Bearing in Aqueous System Strength and Toughness of Graphite Materials for Solid Rocket Motor Energetics of Native Defects in Al2O3 and SiO2 Dynamic Damage Behavior during Cooling Process of Ceramic Coatings Characteristics of Fine WO3 Prepared by Emulsion Evaporation Methods Synthetic Processes via Complex Precursors of Rare Earth Manganites with the Perovskite and its Related Structures Application of La2O3-B2O3-TiO2 Glass-Ceramic for Low Temperature Co-Fired Ceramic (LTCC) Materials Determination of Diffusion Kinetic Parameters and Potential Barrier Height at the Grain Boundary of the Semiconducting SrTiO3 Ceramics Structure and Dissolution Properties of Phosphate Glasses for Glass Fertilizer Phase Behavior of La1-xMnO3-1.5x with Trivalent Manganese Ion Photoluminescence Properties of Ba-Substituted SrAl2O4:Eu Phosphor On Impact Characteristic Evaluation in CF/Epoxy Composites under Falling-Weight Impact Loadings Effect of Mo Addition on Microstructure and Properties of Nb/Nb5Si3 In-Situ Composite On Ultrasonic Characteristics in Carbon/Phenolic Matrix Composite Materials Residual Stress Distribution in Graded PSZ/Inconel Composite Deposited by Particle Collision Thermal Expansion Behavior of the Multiphase Composite System Microwave Behavior of -Fe/Fe3B/Y2O3 and -Fe3N/Y2O3 Resin Composites in GHz Range Effect of Electric Current and Sliding Speed on Wear Rate of Metallized Carbon Strip Sliding against Copper Trolley Evaluation of Solid Lubricant Coatings for Low Friction and Wear Resistance Using the Atmospheric Plasma Spray Relationships between Textures and Surface Roughness, Frictional Behavior, Erosion and Corrosion Properties of TiN Films An Investigation on the Strength-Porosity Relation in Sintered 17-4 PH STS Produced by Powder Injection Molding Rapid Tooling for Injection Moulding Process Gas Analysis in Spark Plasma Sintering of Hydroxyapatite Synthesis of CNTs/Metal/Al2O3 Nanocomposite Powders by Chemical Vapor Deposition Breakage Mechanism of Al2O3 Layer on Nano Al Powder by Magnetic Pulsed Dynamic Compaction Phase Relation and Room Temperature Mechanical Property of Cr2Zr Based Laves Phase Thermal Stability and Mechanical Properties of Nanocrystalline L12 Al3Hf and (Al+12.5 at.%Zn)3Hf Prepared by MA and SPS High Temperature Oxidation of Ti39.4Al10V Alloy High Temperature Oxidation Mechanism of TiAl-W-Si Alloys Oxidation of (Al+12.5%Cu)3Zr Intermetallics Synthesized by Mechanical Alloying Oxidation of (Al+8%Mn)3Ti Intermetallics Synthesized by Mechanical Alloying High Temperature Deformation Behavior of a Ti-45.5Al-2Cr-4Nb-0.4B Intermetallic Compound Work Hardening and Flow Softening of -TiAl Containing Ni Deformation Behaviors of Nb Doped Gamma Titanium Aluminides Yield Stress Anomalous Behavior in -CuZn Alloy Tensile Properties of MoSi2 at Elevated Temperatures Fatigue and Contact Damage of Layered Machinable Ti3SiC2 Ceramics Effects of Material Properties on Elastic Characteristics of Cold Forged Part Elastoplastic Line Contact in Cylindrical Indentation Ductile-Brittle Transition Behaviors with Two Striker Geometries in the Instrumented Charpy Impact Test Effect of -Stabilizing Transition Elements on Elastic Modulus of Ti-M Systems Thermal Fatigue Behavior of the Surface Treated Hot Die Steel Depending on Test Temperature Formation of Shear Texture and Ultra-Fine Grains during Equal Angular Channel Rolling and Subsequent Annealing in AA 3003 Sheet Correlation between Microstructure and J-R Fracture Resistance of AISI Type 347 Weld Effect of Temperature on Strength and Residual Stress Distribution in Silicon Nitride to 304 Stainless Steel Brazed Joints High Temperature Background Characterization of Internal Friction for Fine-Grained Nickel/Zirconia Composite Interfacial Morphology of Duplex Stainless Steel Joints Brazed with Ni-Cr-Si-B Filler Metal Growth Kinetics of IMC Formed between Sn-3.5Ag-0.75Cu BGA Solder and Electroless Ni-P/Cu Substrate by Solid-State Isothermal Aging Influence of Shear Speed on the Shear Force of Eutectic Sn-Pb and Pb-Free BGA Solder Joints Effect of Argon Ion Bombardment on Diffusion Bonded Joint of Various Metals Effect of Oxygen Content on Thermoelectric Properties of Sintered Bi-Te Based Compounds Thermoelectric Properties of the Pseudogap Fe2VAl System Electrical Properties of G4-48azo Dendrimer Containing Azobenzene Functional Groups Thermoelectric Properties of Undoped CoSb3 Comparison of Pd/Ge/Ti/Pt and Pd/Si/Ti/Pt Ohmic Contacts to N-Type InGaAs for AlGaAs/GaAs HBTs Relationship between Splat Morphology and Property of Plasma Sprayed Alumina Coatings Characteristics of Ni-Ti-Zr-Si-Sn Bulk Amorphous HVOF Coating Isothermal Crystallization of Zr55Al10Ni5Cu30 Bulk Amorphous Alloy Near the Glass Transition Temperature Deformation Behavior of Ni-Based Metallic Glass Matrix Composites Reinforced by Brass Short-Fibers Synthesized by Warm Extrusion of Powders Crystallization Behaviors of the Bulk Amorphous Alloy Ni60Zr25Al8Y7 New Cu-Based Bulk Metallic Glasses with High Strength of 2000 MPa Structural and Optical Features of Si-Rich SiO2 Films Prepared by Magnetron Sputter Techniques White Light Emitting Diodes of GaN-Based Sr2SiO4:Eu and the Luminescent Properties Annealing Temperature Effect of PbZr0.4Ti0.6O3 Film on La1/2Sr1/2CoO3 Bottom Electrode Optical and Microstructural Properties of TiO2, Al2O3 and SiO2 Single Layers Deposited by Plasma Assisted E-Beam Evaporation Heat Capacities of Ln2MnNiO6 (Ln = Rare Earth) Structural Analysis of a Complex Oxide Eu2Mn2/3Nb4/3O7 with a Pyrochlore-Related Structure Effects of External Electrode and Heat Treatment on Stress Anisotropy and Residual Stress in BaTiO3-Based Ni-MLCCs Characteristics of ZnO Thin Film by Atomic Layer Deposition for Film Bulk Acoustic Resonator Holographic Recording in Congruent LiNbO3 Co-Doped with Tb and Fe Characteristic Investigations of Stoichiometric LiNbO3 Single Crystal Fiber Co-Doped with Tb and Mn Electrical/Optical Properties of Thin Transparent Oxide Films Deposited Using DC Magnetron Sputtering Characteristics of SnO2 Thin Films Deposited by RF Magnetron Sputtering Properties of Tin Oxide Films Prepared by MOCVD Electrical and Optical Characterization of Indium Tin Oxide (ITO) Films for Low Resistance Transparent Electrode Characteristics of HfO2 Dielectric Layer Grown by MOMBE Structural, Optical and Electrical Properties of ZnO Films by Sol-Gel Method Antireflection Layer Coatings on the Si Solar Cell Using SiO2 and Si3N4 Nanostructural and PL Features of nc-Si:H Thin Films Prepared by PECVD Techniques Preparation and Characterization of Organic Light Emitting Devices Using QD Dopant XPS Analysis and Atomic Force Microscopy Observation of Micro-Liquids Adsorbed on Pure Iron and Copper Surfaces Microstructures and Magnetic Property of Bulk and Thin Film Co2MnGe Heusler Compound Fabrication of SiO2-Coated Magnetic Nanoparticles for Applications to Protein Separation and Purification Shock Consolidation of Sm-Fe-N Magnetic Powders and Magnetic Properties Magnetotransport in Ferromagnetic (Ga,Mn)N Epitaxial Films Synthesis and Crystal Structure of Hexagonal DyMnO3 Influence of Annealing Temperature on Magnetic Properties in Co-Based Amorphous Ribbons Structure Dependent Oxidation of Al Thin Films for MTJ Tunnel Barrier Properties of Nd-Fe-B Magnetic Powder Prepared by Reduction-Diffusion Process Using a Spray-Dried Precursor Magnetotransport Properties in Semimetallic Bismuth Thin Films Origin of Thermal Stability of IrMn Based Specular Spin Valve Type GMR Multilayer Planar Hall Effect of GaMnAs Measurements of Magnetic Compton Profiles of Amorphous Fe-Tb Thin Films Using Circularly Polarized X-Rays Effect of Zr-Substitution on the Magnetic Property of a YIG Ferrite Magnetotransport Properties in a Lateral Spin-Injection Device with a Ferromagnetic/Si/ Ferromagnetic Junction New Manufacturing Process of Nickel-Free Austenitic Stainless Steel with Nitrogen Absorption Treatment Mechanical Properties of Binary Ti-Ta Alloys for Biomedical Applications Transformation Behavior and Shape Memory Characteristics of Ti-45Ni-5Cu(at%) Alloy Ribbons Fabricated by Melt Spinning Porous TiNi Biomaterial Produced by Self-Propagating High-Temperature Synthesis: Pore Structure, Mechanical Property and Application Densification and Mechanical Property of Nanostructured NiAl Produced by Mechanical-Alloying and Spark-Plasma Sintering Mechanochemical Synthesis of Nano-Sized CeO2 and its Application for CMP Slurry Manufacturing of Cu-15.0Zn-8.1Al Shape Memory Alloy Using Spark Plasma Sintering Microstructure of Cu-TiB2 Nanocomposite during Spark Plasma Sintering Photocatalytic Activity of SiO2-TiO2 Nanoparticles Prepared by Sol-Hydrothermal Process Apatite Formation on PDMS-Modified SiO2-CaO-P2O5 Hybrids Prepared with Different P2O5 Content by Sol-Gel Method Effect of Heating Rate on Sintered Microstructure of W-Cu Nanocomposite Powder Produced Using W-CuO Mixture Study of Phase Transformation of Nano Al2O3 Compacts Derived by Hydrolysis and Subsequent Thermal Sintering of Al Powders Quenching of Growth of Zinc Oxide Nanoparticles by Adsorption of Organic Stabilizers Synthesis of Nano Metal Powder by Electrochemical Reduction of Metal Oxides Sintering Behavior of the Powder Injection Molded Nanocrystalline Fe-50wt%Ni Synthesis of ZnO Nanoparticles Embedded in a Polymeric Matrix
• Effect of Curing Temperature Formation of Nanocrystalline Structure in Steels by Air Blast Shot Peening and Particle Impact Processing Threshold-Varying Method of Stationary Wavelet Denoising for Ultrasonic Speckle Reduction Synthesis and Properties of Silica-Modified Polybenzoxazine Preparation of Monodispersed and Nano-Sized Spherical SiO2 Particles by Emulsion Method Fabrication of Oxide/Semiconducting Coaxial Nanotubular Materials Using Atomic Layer Deposition Synthesis of Ultra-Fine Iron-Oxide Nano-Particles in a Diffusion Flame with Electro-Spraying Assistance Characteristics of Fe2O3/SiO2 Nano-Composites Particles Prepared by a Diffusion Flame with Premixed Precursor Microstructural Evolution on Dissolution of Commercial Calcium Phosphate Ceramics Properties of Catalytic Filter for the Hot Gas Cleaning Comparison of III- Nitride Nanotubes: Atomistic Simulations Application of Water-Based Alumina Tapes Prepared Using PVP Binder for All-Ceramic Dental Crowns Correlation between Thermal Expansion Coefficients of La2O3-Al2O3-SiO2 Glasses and Strength of the Glass Infiltrated Alumina for all Ceramic Crown Characterization of High Temperature Oxidation Properties of Silicon Carbide Nanofibers Magnetorheological Characterization of Polymer-Iron Composite Suspensions Effects of Layered Silicate on Nanoscopic Internal Structure and Morphology in Polymer Blend Ultrasonic Characterization of Degradation of Aging Epoxy Coating Fabrication of Al2O3/5 vol% Cu Nanocomposites Using Various Powder Mixtures and Its Properties Effect of Sintering Atmosphere on the Microstructure of Hot-Pressed Al2O3/Cu Nanocomposites Effect of Bioactive Grade Surface on In Vivo Behavior and Mechanical Stability in Titanium Based Implant Surface-Modified by Plasma Spray Coating and Chemical Treatments Anisotropic Deformation Behavior of the Oriented Nanostructure of a Semicrystalline Terblock Copolymer with Multi-Scale Orderings Cu Nanowire Structures Inside Carbon Nanotubes Durability in Antimicrobial Effects of Silver Doped Hydroxyapatite Depending on the Synthesis Route Comparison of Metal-Oxide Nanoparticle Formation in the Cu and Sn Thin Films by the Reaction with Polyimide Fabrication of Micro PCR Chip and DNA Amplification Prediction of the Structural Performances of ZnO Nanowires Grown on GaAs (001) Substrates by Metalorganic Chemical Vapour Deposition (MOCVD) A Study on Anodic TiO2 Photocatalyst for Water Purification Fabrication Parameters for Highly Ordered Nano-Pore Arrays in Alumina Template Photocatalytic Ecomaterials Hydrophilicity and Bactericidal Effects of TiO2 Thin Films Prepared by RF Sputtering Fatigue Performance of Low Rigidity Titanium Alloy for Biomedical Applications Effects of Alloying Elements on Elastic Modulus of Ti-Nb-Ta-Zr System Alloy for Biomedical Applications Effect of Tin Addition on Phase Constitution and Heat Treatment Behavior in Ti-40Ta-Sn Alloys Wear and Bioconductivity Characteristics of Oxidized Ti-29Nb-13Ta-4.6Zr Microstructure at/around Interface between Plasma-Sprayed Hydroxyapatite and Ti Alloy Reciprocal Tribocontact of Biomedical Alloys Synthesis of Apatite Ceramics with Preferential Crystal Orientation Nanostructured WC-Co Coatings from Different Feedstock Powders Surface Modification and Characterization of Perovskite-Type Mixed Ionic-Electronic Conductors Oxidation of Thermal Sprayed Metallic Materials during Flying in Air and the Coating Structures Cold Spray Process ~ Overview and Application Trends ~ Flattening Problem of Thermal Sprayed Particles Composition Design and Ageing of Ni-Mn-Ga Alloys Clinical Application of TiNi Shape Memory Alloy Bone Fastener Property of TiNi Shape Memory Foils Produced by Ultrafine Laminates Method Thermodynamic Analysis of Thermoelastic Martensitic Transformations

「Nielsen BookData」 より

詳細情報

• NII書誌ID(NCID): BA66596572
• ISBN:
  • 0878499393
  • 0878499393
• 出版国コード: sz
• タイトル言語コード: eng
• 本文言語コード: eng
• 出版地: Zuerich
• ページ数/冊数: 2 v.
• 大きさ: 25 cm
• 親書誌ID:
  • BA00294222