Life cycle tribology : proceedings of the 31st Leeds-Lyon Symposium on Tribology held at Trinity and All Saints College, Horsforth, Leeds, UK, 7th-10th September 2004
著者
書誌事項
Life cycle tribology : proceedings of the 31st Leeds-Lyon Symposium on Tribology held at Trinity and All Saints College, Horsforth, Leeds, UK, 7th-10th September 2004
（Tribology and interface engineering series / editor B.J. Briscoe, v. 48）
Elsevier for the Institute of Tribology, The University of Leeds and Institut National des Sciences Appliquées de Lyon, 2005
大学図書館所蔵 件 / 全7件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references
内容説明・目次
内容説明
The 31st Leeds-Lyon Symposium on Tribology was held at Trinity and All Saints College in Leeds under the title "Life Cycle Tribology" from Tuesday 7th September until Friday 10th September 2004. Over the three days of presentations that followed, life cycle tribology was explored across a range of areas including automotive tribology, bearings, bio-degradability and sustainability, bio-tribology, coatings, condition monitoring, contact mechanics, debris effects, elastohydrodynamic lubrication, lubricants, machine systems, nanotribology, rolling contact fatigue, transmissions, tribochemistry and wear and failure. Invited talks in these fields were presented by leading international researchers and practitioners, namely C.J. Hooke, J.A. Williams, R.J.K. Wood, G. Isaac, S.C. Tung, D. Price, I. Sherrington, M. Hadfield, K. Kato, R.I. Taylor, H.P. Evans, R.S. Dwyer-Joyce and H. Rahnejat.
目次
- Introduction A Short History and Summary of Publication Arrangements for the Leeds/Lyon Symposia on Tribology
- Symposia-1-31, (1974-2004) Refereeing Session I: Keynote Addresses Technology of a Traction Drive CVT - Past, Present And Future Life Cycle Engineering and Virtual Product Development - the Role of Tribology Session II: Elastohydrodynamic Lubrication 1 The effect of roughness in EHL contacts Complete numerical analysis for mixed boundary and thermal elastohydrodynamic lubrication in steady-state point contacts The influence of slide-to-roll ratio on lubricant film thickness distribution in the vicinity of real roughness features passing through EHD point contact Unsteady EHL: An inverse hydrodynamic formulation Session III: Nanotribology 1 Some aspects of tribological behaviour at the micro-scale - with particular reference to MEMS and MMAs Chain matching effects of base oils and additives in nanotribology of boundary films Lubrication properties of AI2O3 nanoparticles in aqueous suspensions Session IV: Lubricants 1 Electrostatic monitoring of the effects of carbon black on lubricated steel/steel sliding contacts Evaluation of Ionic Liquids for the Application as Lubricants Measurement method of physical properties of adsorbed layers Effectiveness of boundary lubricant additives on some coated surfaces Session V: Bio-Tribology 1 Life Cycle Aspects of Total Replacement Hip Joints Evaluation of wear resistance of ultra-high molecular weight polyethylene for joint prostheses in the multi-directional pin-on-plate tester The influences of lipid and protein concentration on wear of ultra-high molecular weight polyethylene Wear process under concentrated contact in alumina/alumina hip joint Session VI: Coatings 1 An In-Situ Tribotest Method Designed for Predicting Wear Life and Frictional Performance During the Aluminum Forming Process Durability of perfluoropolyether nanolubricant film fixed on diamond-like carbon surfaces Rolling and rolling-to-sliding contact behaviour of DLC coatings Session VII: Transmissions A Full Toroidal Traction Drive IVT for Automotive Volume Production Effects of the Maximum Hertzian Pressure on the Maximum Traction Coefficient Under EHL Conditions Structure and mechanical property of boundary lubricating film formed in belt-type CVT oil Efficiency modelling in the full toroidal variator: Investigation into optimisation of EHL contact conditions to maximize contact efficiency. Session VIII: Tribochemistry Tribochemical approach toward mechanism for synergism of lubricant additives on antiwear and friction reducing properties Tribochemistry of mono molecular additive films on metal surfaces, investigated by XPS and HFRR Water-accelerated chemical reaction for producing gear teeth with high form accuracy and fine surface finish Session IX: Condition Monitoring Condition Monitoring as a Tool to Aid Compliance with ISO 14000 Evaluation of an Ultrasonic Method for Measurement of Oil Film Thickness in a Hydraulic Motor Piston Ring Ultrasonic Reflection from Mixed Liquid-Solid Contacts and the Determination of Interface Stiffness Session X: Rolling Contact Fatigue Extended finite element method for numerical simulation of 3D fatigue crack growth A mixed mode fatigue crack model with the coupled X-FEM/LATIN method. Application to rolling contact fatigue (RCF) Study on Rolling Contact Fatigue in Hydrogen Atmosphere - Improvement of Rolling Contact Fatigue Life by Formation of Surface Film - Rolling Contact Fatigue Life of Bearing Steel Rollers Lubricated with Low Viscosity Traction Oil Session XI: Bio-Tribology 2 Diatom Biotribology Friction of Contact Lenses: Silicone Hydrogel versus Conventional Hydrogel Modelling the blood flow in an aorta
- the MPTT and Modified MPTT models. A novel technique for evaluation of articular cartilage lubrication based on the surface plasmon resonance Session XII: Coatings 2 The Effect of Si Content and Substrate Bias on Structural and Tribological Properties of (Cr,Si)N Coatings under Water Lubrication Tribological characteristics of WC1-x, W2C and WC tungsten carbide films Session XIII: Lubricants 2 Power Loss in FZG gears lubricated with industrial gear oils: Biodegradable Ester vs. Mineral oil The effect of dissolved ions on tribological properties in water Comparative Theoretical and Experimental Study of Linear and Star Polymer Additive Degradation in Kurt Orbahn Tests Session XIV: Bio-degradability - Sustainability Sustainable Development Thinking in Tribology Design Sliding experiments of steels in gaseous hydrogen Ecological-friendly Oil Film on Water Fog Metalworking Fluid Lubrication in Refrigeration Systems: Performance of Journal Bearings Lubricated with Oil and Refrigerant Mixtures Session XV: Machine Systems 1 Modern Tribology in Life Cyele Assessment An experimental study on the friction behaviour of aircraft hydraulic actuator elastomeric reciprocating seals Experimental Study on Gas Transportation in Radial Shaft Seals Friction coefficient between gear teeth in mixed film lubrication Session XVI: Contact Mechanics, Wear and Failure Analytical Studies of Contact Problems for Fractal Surfaces A model of seizure based on Burwell and Strang's concept of wear mode transition An Asperity Based Model for Wear Rate in Mixed Lubrication Session XVII: Automotive 1 Lubricants & Energy Efficiency: Life-Cycle Analysis Starved Hydrodynamic Lubrication of the Piston Ring Cylinder Liner Contact: Preliminary Study of the Influence of Surface Texturing A Model for Diesel Fuel Additive Lubricity The Degradation of Lubricants in Gasoline Engines: Development of a Test Procedure to Evaluate Engine Oil Degradation and its Consequences for Rheology Session XVIII: Elastohydrodynamic Lubrication 2 Surface contact and damage in micro-EHL The Transient Elastohydrodynamic Friction Analysis of Main Bearings Numerical analysis of the thermal micro-EHL problem of point contact with a single surface bump Roughness Amplitude Reduction under Non-Newtonian EHD Lubrication Conditions Session XIX: Coatings 3 Sliding wear of oxygen diffusion hardened Ti-6A1-4V in physiological saline Hard coatings durability under fretting wear The effect of the crystallographic orientation of Ag thin films on their tribologieal performance The Effect of Sliding History on the Steady State Friction Coefficient between CNX Coatings under N2 Lubrication Session XX: Wear and Debris Effects The Life Cycle of a Debris Particle Experimental investigations of Rolling Contact Fatigue of dented surfaces using artificial defects Stability, Wear, and Corrosion Characteristics of Rapidly Solidified High Temperature AI-8Fe-4Ce Alloy Predicting the growth of RCF crack with the use of the 3D multi size finite element model. Session XXI: Bearings Integrated Tribological Analysis within a Multi- physics Approach to System Dynamics Tribological performance of selected bearings and bearing materials used for nanopositioning Influence of Manufacturing Error of Roundness for Characteristics of Cylindrical Journal Bearing Session XXII: Automative 2 Additive/additive interactions in boundary lubrication - a study of film formation and tenacity Fundamental Study of Changes in Friction and Wear Characteristics due to ZnDTP Deterioration in Simulating Engine Oil Degradation during Use (Part 2) -- Influences of the Presence of Peroxide and Dispersed Zn-containing Solids-- The Degradation of Lubricants in Gasoline Engines: Lubricant Flow and Degradation in the Piston Assembly Session XXIII: Machine Systems 2 Seizure Tests to Select Materials for Cylinder Blocks and Valve Plates in Water Hydraulic Pumps A reduced-scale testing machine for tribological evaluation of brake materials Experimental-Numerical Friction Factor Determination Session XXIV: Nanotribology 2 Effects of Ultra-Violet Irradiation on Conformation and Spreading Characteristics of Molecularly Thin Lubricant Films Friction and wear life evaluation of silane based self assembled monolayers on silicon surface Basic Observations of Tribological Phenomena by Neutron Scattering Methods Session XXV: Bio-tribology 3 The Importance of Protein Physisorption in BioMEMS/NEMS Applications: A Nanotribological Study Metal-metal cervical disc implants: A material investigation using pin-on-plate tests Written Discussion List of Delegates
「Nielsen BookData」 より