The science of engineering ceramics : proceedings of the 3rd International Symposium on the Science of Engineering Ceramics(EnCera'04), October 31st-November 3rd, 2004 : in conjunction with the 12th International Seminar on the Core University Program(CUP) between Japan and Korea
Author(s)
Bibliographic Information
The science of engineering ceramics : proceedings of the 3rd International Symposium on the Science of Engineering Ceramics(EnCera'04), October 31st-November 3rd, 2004 : in conjunction with the 12th International Seminar on the Core University Program(CUP) between Japan and Korea
（Key engineering materials, v. 317-318 . CSJ series-publications of the ceramic society of japan ; v. 14）
Trans Tech Publications , Ceramic Society of Japan, 2006
- 3
Available at / 4 libraries
-
No Libraries matched.
- Remove all filters.
Note
"The 3rd International Symposium on the Science of Engineering Ceramics(EnCera 04) was held in Osaka, Japan during the period of October 31 to November 3, 2004" -- Preface
Includes bibliographical references and indexes
Description and Table of Contents
Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).
This book contains more than 200 papers; all dealing with recent research findings related to engineering ceramics and associated materials. Particular emphasis is placed on the consideration of novel technical challenges and innovative technologies in advanced engineering ceramics: including new classes of high-temperature structural ceramics, nanomaterials/nanocomposites, environmental- and energy-related ceramics and so on, which are expected to open up new frontiers for engineering ceramics in the 21st century.
Table of Contents
- Investigation of the Sintering Behavior of Ultrapure -Alumina Containing Low Amounts of SiO2 or CaO Sintering Behavior of Microstructured -Alumina with Nanosized -Alumina Additive Control of Shrinkage during Sintering of Alumina Ceramics Based on Master Sintering Curve Theory Bulk Consolidation of Non-Oxide Ceramic Powders Derived from Polymer Precursors Centrifugal Sintering Low-Temperature Sintering of - and -SiC Powders with AlB2 Additive Sintering and Characterization of Zr2Al3C5 Monolith Thermal Evolution of Single Phase Lanthanum Zirconate Sinterability of Alumina-Dispersed 3Y-TZP Preparation of Ce-ZrO2 Based Composites and Effect of Addition of 3Y-ZrO2 on Their Microstructures Grinding of Agglomerate AlN Powder by Wet Milling Wet Jet Milling of Ceramics Powder Hydrothermal Preparation and Characterization of Barium Titanate Powders Fabrication and Characterization of Various Calcium Phosphate Powders by Ultrasonic Spray Pyrolysis Technique Fabrication and Characteristics of Hypereutectic Prealloyed Al-Si Powders by Gas Atomization Process Effect of Magnesium Ion on the Precipitation of Hollow Calcium Carbonate by Bubble Templating Method Effect of Different Salt on Fabrication of Sr0.5Ba0.5Nb2O6 by Molten-Salt Synthesis Processing and Property Evaluation of Alumina Aerogel Based Ceramic Nanocomposites Dispersion of ZrO2 Particles in the Al2O3/ZrO2 Ceramics by the Partial Chemical Dispersion Processes Pre-Combustion CO2 Capture Using Ceramic Absorbent and Methane Steam Reforming Kumada Rearrangement of Polydimethylsilane Using a Catalytic Process Effect of Additives on Hydrolysis of Ti Alkoxide and Microstructural Observation of TiO2 Sol-Gel Preparation and Characterizations of Europium-Ion Doped Barium Magnesium Aluminate Syntheses of Bulky Y-Zeolite by Hydrothermal Hot-Pressing (HHP) Technique Densification and Strengthening of Tricalcium Phosphate/Titania Composite by Hot Pressing Preparation of Mullite Composite Using Liquid Infiltration Technique Liquid-Phase Sintered Silicon Carbide with Aluminum Nitride and Rare-Earth Oxide Additives Effect of -Alumina as a Seed in Alumina/Silicon Carbide Composites Preparation and Morphology of C/C-SiC Composites by Si Melt Infiltration Preparation and Properties of Silicon Nitride Ceramics by Nitrided Pressureless Sintering (NPS) Process Microwave Sintering BaTiO3 Ceramics Using Liquid Phase Sintering Thermodynamical Calculations and Experimental Confirmation about the Mg-Al-Spinel Reaction Path in the Sol-Gel-Process Fabrication and Structure of TiO2 Coated Open-Cell Mullite Ceramics Dispersion of Barium Ferrite Particles for Slip Casting in Magnetic Field The Vibrative Casting with a Thixotropic Behavior Compositional Control in Solid Freeforming
- Fabrication of 3D FGM Microstructural Characterization of Fine-Grained Pb(Zr0.52Ti0.48)O3 Ceramics Fabricated by a Spark Plasma Sintering Rapid Fabrication of C/C-SiC Composites Strengthening Effect of In-Situ Dispersed Hexagonal Boron Nitride in Ceramic Composites Biomorphic SiC Ceramics Prepared by Organic Template Method Fabrication of a Strontium-Doped Lanthanum Chromite (LSC) Thin Film on SUS430 Substrate Influence of Nitride on Sinterability of the Composite of Lithium Aluminum Silicate and Silicon Carbide Hydrogen Reduction and Sintering Behavior of Al2O3/CuO Powder Mixtures Prepared from Different Raw Powders Low Cost Si3N4/SiC Nanocomposites, Processing, RT and HT Properties Fabrication of Si3 N4-TiN Nanocomposites via Various Routes Hydrothermal Synthesis of Nano ZrO2 Powders Synthesis of Nanocrystalline -Al2O3 Using a 2-Step Calcination Method Nano Magnetite Particles Prepared under the Combined Addition of Urea and Ammonia Synthesis of Nano-Scaled -Al2O3 Particles by Combustion Spray Pyrolysis Synthesis of SiC Nano-Powders by Solid-Vapor Reaction Formation Mechanism of Nano AlN Powder by Gas-Reduction-Nitridation Synthesis of Metal Oxide Hollow Nanoparticles by Chemical Vapor Condensation Process Microwave-Assisted Synthesis of MWO4 and MMoO4 (M = Ca, Ni) Nano-Powders Using Citrate Complex Precursor Synthesis and Microstructure of TiO2-SiO2 Nanoparticles by a Reverse Micelle and Sol-Gel Processing Fabrication and Applications of Nano-Metal Particle Composites by Ultrasonic Eco-Process Fabrication and Estimation of Au Coated -Fe2O3 Nanoparticles for Separation and Purification of Biomolecules Nano-Structured High Purity Copper Processed by Accumulative Roll-Bonding Direct Hydrothermal Processing of Long Titanate Nanofibers from Natural Rutile Synthesis of Nanotubular Titanate from Titanium Using Hydrothermal Treatment Synthesis and Properties of Titania Nanotube Doped with Small Amount of Cations High Pressure / Low Temperature Sintering of Nanostructured Titania by Internal Heating Method Growth of Carbon Nanotubes on Surface of Carbon Fibers Rod On the Dissolution of WC in WC-Co Alloys Conventional Sintering Route for the Production of Alumina-Based Nanocomposites: A Microstructural Characterization Energy Changes and the Lattice Resistance Shot Peening - A New Method for Improving Mechanical Properties of Structural Ceramics Critical Frontal Process Zone Size and R-Curve Behavior of Porous Ceramics Characteristics of Machining Damage and Their Influence on Strength in Alumina Ceramics System Estimation of Residual Stress in a Ceramic Coating Layer From Niihara's Equation to Peculiar Nanoindentation Deformation of Ceramics and Semiconductors Fracture Toughness of Fibrous Si3N4 Monolithic Ceramics Prediction of Fracture Toughness in Fibrous Si3 N4 Monolithic Ceramics Mechanical Properties of Transparent Polycrystalline Silicon Nitride Electrical Resistance Behavior during Tensile Loading of Al2 O3 Fiber-Nano RuO2-Glass Composites Gas Pressure Dependence of Photon Emission Accompanying Fracture of Polycrystalline MgO in Nitrogen Mechanical Properties of Sol-Gel Inorganic-Organic Hybrid Films in Nanoindentation The Change of Mechanical Properties for Anodic Aluminum Oxide by Heat Treatment Microstructures and Mechanical Properties of Nano-Structured Aluminum Fabricated by Accumulative Roll-Bonding Using Different Rolling Methods The Microstructures and Mechanical Properties of Molybdenum Disilicide Preforms Infiltrated by Aluminum Development of Low Machining Cost Materials by Using Aluminum Borate Estimation of Thermal Shock Resistance by Infrared Radiation Heating and Water Flow Cooling Techniques Improvement in Oxidation and Thermal Shock Resistance of Molten Glass-Coated Carbon Materials by Interfacial Control Microscopic Study of Sliding Wear Surfaces of Alumina Dry Sliding Wear of Lu2O3 Sialon Ceramics Increasing the Effectiveness of Aluminium Phosphate Binders Rolling Life Properties of Ceramic Bearings in Water Tribological Properties and Thermal Conductivity of Si3 N4 / Si3N4-BN Alternate Layered Composites Wear Behavior of Nano-Sized Metal Particle Dispersed Al2O3 Nanocomposites Fabrication of Nanoabrasive Grinding Wheels and Their Application to Grinding Silicon Wafers Tribological Property of Plasma Sprayed TiO2 Coating Adhesive and Wear Properties of Indium Tin Oxide (ITO) Thin Films Deposited by RF Magnetron Sputter Tribological Properties of TiN/DLC Nanocomposite Coatings Corrosion Resistance of Commercial Si3N4 Bearing Balls Characteristic Evaluation of High Corrosion Resistant Ti/ (Pt + B2O3) Electrode with New Microstructure of Coat Effect of Chemical Composition of Intergranular Glass on Superplastic Deformation of -Silicon Nitride Superplastic Deformation of Silicon Nitride Nanocomposite at High Strain Rates Superplastic Behavior in GeO2 - TiO2 Doped TZP Surface Diffusion and Incorporation Process of Adatom in Fe-Al Multilayer System Oxygen Diffusion along Symmetric [0001] Tilt Grain Boundaries in -Alumina Oxynitride Glasses and Their Properties - Implications for High Temperature Performance of Silicon Nitride-Based Ceramics High-Temperature Properties of Silicon Nitride with Lu-Si-O-N Grain Boundary Phases Analysis of Internal Friction on Silicon Nitride with Visco-Elastic Model Deformation Behavior of SiO2 Doped Nanocrystalline Monoclinic Zirconia at Low Temperatures Microstructure and High Temperature Strength Characteristics of Unidirectionally Solidified Al2 O3 /GdAlO3 Eutectic Composite Influence of Grain Boundary Properties on Microcracking of AlN in Sliding Test The Effect of Particle Migration on the Creep-Rate of Nanocomposites Crack Propagation Behavior of Alumina with Different Grain Sizes under Static and Cyclic Fatigue Crack-Healing under Cyclic Stress and Improvement of the Resultant Fatigue Strength of Si3N4/SiC Evaluation and Control of Crack Propagation in Dense Porcelain/ Porous Alumina Layered Structures for Dental Material Applications Critical Conditions for Crack-Healing of Structural Ceramics under Constant or Cyclic Stress Simultaneous Removal of SOx and NOx by Catalytic Cordierite Filter Indentation Contact Deformation of 3Y-TZP at Elevated Temperatures High Temperature Characteristics of Melt Growth Composites and Their Application to Ultra High Efficiency Gas Turbine Components Development and Evaluation of Ceramic Components for a Gas Turbine Effect of Reactive Filler Addition for Matrix of SiC Fiber/SiC Composite Thermal and Electrical Conductivities of Porous Carbon-Coated Ceramic Fiber Composites Laser Chemical Vapor Deposition of Thick Oxide Coatings La2O3 Doped Y2O3 Stabilized ZrO2 TBC Prepared by EB-PVD Deposition Behavior of YSZ Nano-Coating Layer by EB-PVD Thermal Conductivity of Nano-Pore Dispersed Y-PSZ Fabricated by EB-PVD Thermal Stability and Mechanical Properties of Plasma Sprayed Al2O3/ZrO2 Nano-Composite Coating Investigation of Strontium-Niobium Oxides for Application to Thermal Barrier Coatings Thermal Conductivity of Zirconia for Thermal Barrier Coatings: A Perturbed Molecular Dynamics Study Mechanical Properties and Damage Durability of Thermal Barrier Coatings with Thermal Fatigue Advances in YSZ Coatings Prepared by Sol-Gel Route. Applications to Fuel Cells or Thermal Barrier Coatings New Challenge of Plasma Spray Coatings in Nano Oxide Ceramics Development of Nanostructured Al2O3-Ni HVOF Coatings Process Optimization for Nanostructured HVOF -Sprayed Al2O3-Based Ceramic Coatings Quest and Evaluation of Topcoat Materials for Environmental Barrier Coatings of SiC/SiC Composites Reliability during Thermal Shock Testing of NiCr Films on Mn-Ni-Co Oxide Substrates Comparison of Water Vapor Corrosion Behaviors of Ln2Si2O7 (Ln=Yb and Lu) and ASiO4 (A=Ti, Zr and Hf) EBC's Characterization and Photocatalytic Properties of Plasma Sprayed TiO2 Coatings Deposited from Nanoparticles Titania Nanocrystals-Dispersed Coatings from SiO2-TiO2 Gel Films through Hydrolysis and Dissolution Preparation and Characterization of Titania Thin Films Development of Silicon Carbide Coating on Al2O3 Ceramics from Precursor Polymers by Radiation Curing Accelerated Degradation Test of Indium Tin Oxide (ITO) Thin Films Deposited by RF Magnetron Sputter Local Acceleration Effects of Adatom at the Vicinity on the Surface: Case of Co Nano Thin-Films on Al Surface Laser-Assisted Synthesis of Amorphous/Pseudoamorphous GaN Thin Films and Nanostructures The Effects of Nitrogen and Annealing on the Electrical Property of the Diamond-Like Carbon (DLC) Films The Anisotropic Properties of the Tape Cast Si3N4 Ceramics with Rod-Like -Si3N4 Seeds Addition Fabrication and Characterization of Zirconia-Based New Ceramic Composites for Thermal Barrier Coatings Design and Characterization of Porosity Gradient for the Laminated Alumina Tubes Alumina-Based Nanocomposites Fabricated by a Novel Soaking Method Properties and Microstructure of Mullite-Based Iron Nanocomposite High-Toughness Tetragonal Zirconia/Alumina Nano-Ceramics Microstructures and Mechanical Properties of Fine-Scale Fibrous Alumina / Zirconia Bi-Phase Composite Fabricated by Co-Extrusion Process Nanocomposite Formation in the Fe3O4-M (M=Al, Ti) Systems by Mechanical Alloying Fabrication of -Sialon Nano-Ceramics Fabrication and Evaluation of -SiAlON Nanoceramics Fabrication and Properties of Machinable AlN-BN Ceramic Nanocomposites Electrical Properties of AlN-SiC Ceramics Fabrication of Electronic Conductive Silicon Nitride Ceramics by Convenient Powder Metallurgical Process Effect of Oxynitride Grain Boundary Phase on Toughening of Silicon Nitride Ceramics Electrically Conductive Aluminum Nitride Ceramics Containing In-Situ Synthesized Boron Carbonitride Fabrication of Conductive Alumina by Gelcasting and Reduction Sintering Preparation and Electrical Properties of Carbon Nanotubes Dispersed Zirconia Nanocomposites Synthesis and Densification of CNTs/Fe/Al2O3 Nanocomposite Powders by Chemical Vapor Deposition Preparation of Organic/Inorganic Nanocomposites with Microwave Process Fabrication of Yttria Stabilized Tetragonal Zirconia Polycrystals Containing TiNi Intermetallic Compounds Synthesis of Monodispersed Inorganic-Organic Hybrid Particles from Phenyltriethoxysilane Evaluation of Thermal Stability of Porous Material by Sintering Stress Preparation and Properties of Porous Alumina Ceramics with Oriented Pores Fabrication and Characteristic of Porous Alumina Developed with SiC Nano-Fiber or Nano-Whisker Preparation of Ceramic Honeycomb Filter Supported Zeolite Membrane Modules by Microwave-Assisted In-Situ Crystallization In-Situ Formation and Coating of Cordierite Whiskers on Cordierite Based Honeycomb Support Fabrication of Porous Ni-ZrO2 for SOFC Using NiO-ZrO2 Composite Powders Synthesis and Application of Nano Porous La0.6Sr0.4CoO3- on an Oxygen Separation Membrane Durability of Ceramic Filter for Hot Gas Cleaning Macroporous Ceramics Coated with Mesoporous Layer for Enzyme Encapsulation Preparation of Bimodal Porous Apatite Ceramics through Slip Casting Using Fine Hydroxyapatite Powders Fabrication of Uniformly Nano-Sized Macroporous Silica Structure Using Templates Fabrication of Large Ceramic Components with Controlled Microstructure by Powder Thermoset Molding Mineral Sand as a Low Cost Source of Nanomaterials Fabrication and Characterization of Zeolite-Carbon Composite from Industrial Wastes Evaluation of Energy Consumption in Ceramic Fabrication Process for Alumina Ceramics with Diverse Particle Sizes Fabrication of Al2O3 Ceramics by Environmentally Friendly Process Characteristics of Wall and Floor Tiles Using Waste Glass Honeycomb Supports, Filters and Catalysts for Cleaner Environment Preparation of Porous Hydroxyapatite Using Extrusion of PAN Synthesis and Characterization of Calcium Phosphate-AMP Layered Materials Finite Element Analysis on Proof Testing of Ceramic Ball Heads for Total Hip Replacements: Trauma Loading Considerations Application of Zeolites on Cellulose Fiber Formation of Hydroxyapatite from Mechanochemically Treated -Tricalcium Bis (Orthophosphate) Transmission Electron Microscopic Study on Thermal Decomposition Process of Calcium-Deficient Hydroxyapatite Dissolution and Mechanical Properties of Sintered Hydroxyapatite Immersed in Water Correlation of Physical Properties of Inorganic Carrier and Microbial Survival Rate Luminescence Properties of Rare-Earth Doped -SiAlONs Effects of Sn2+ Co-Doping on the Photoluminescence of Eu3+ Ion in Strontium Phosphate Synthesis of WO3 Electrochromic Sensor by Sol-Gel Method and Characterization of Its Electrochemical and Optical Properties Thermoelectric Properties of Al-Doped ZnO Prepared by Electrical Field-Assist Sintering Photocatalytic Activity of Titania and Zirconia-Doped Titania Nanocrystals Prepared by Surfactant-Assisted Templating Method Comparison of Adsorption Capability and Photocatalytic Activity for Methylene Blue Decomposition of LiInO2 with NaInO2 The Preparation of Visible Light-Responsive TiO2 Thin Films by Applying a RF-Magnetron Sputtering Deposition Method and Their Photocatalytic Reactivity for the Decomposition of Water with a Separate Evolution of H2 and O2 The Intelligent Catalyst: Pd-Perovskite Having the Self-Regenerative Function in a Wide Temperature Range The Self-Regenerative "Intelligent" Catalyst for Automotive Emissions Control Removal of Heavy Metal Ions from Aqueous Pb-EDTA and Cu-EDTA Solutions Using Nanosized ZnO Powders by Solution-Combustion Method Synthesis of Solution-Combusted ZnO Nanopowder and Its Application to Gold Recovery Effect of Additives on Dielectric Loss of AlN Ceramics Dielectric and Piezoelectric Properties of xPb(Ni1/3Nb2/3)O3 - yPb(Mn1/3Nb1/3Sb1/3)O3- (1-x-y)Pb(Zr0.48Ti0.52)O3 Ceramics Effect of Sintering Temperature on Structure, Piezoelectric and Ferroelectric Properties of (Na0.5Bi0.5)0.90Ba0.10TiO3 Ceramic Thermodynamic and Dielectric Properties of MgSiN2 Ceramics Ultrasonic Spray Nozzle System with Piezoelectric Ceramics for Water Treatment Applications Pressure Sensing Using Electrostatic Capacitance Preparation and Evaluation of Metal/Ceramic Nanocomposites for High Frequency Inductive Devices Microstructural and Electrical Characterisation of LaxBa1-xTi1-xYxO3 (0 x 0.50) Ceramics A Structural Consideration of a Solid Solution La4Ni3-xMnxO10 Extraction of Crystal Structures Based on Euclidean Voronoi Diagram and Angle Distributions among Atoms Sintering and Electronic Conducting Properties of La0.8Ca0.2CrO3 Perovskite-Type Complex Oxides Synthesized by Different Methods Magnetic and Electronic Properties of Transition Metal Doped -SiC - A Diluted Magnetic Semiconductor Development of Ferrite Magnetic Materials with High Strength by a Low-Temperature Sintering Method Processing and Mechanical Properties of Microcellular Ceramics Preparation and Properties of a Novel Anode of Interpenetrating Phase Composite Structure Fabrication and Fuel Cell Properties of Gd-Doped CeO2 Micro-Tube Ceramics Reactors Prepared by Gel Precursor Preparation of YSZ Electrolyte for SOFC by Electron Beam PVD Effect of Alumina Additions on Mechanical and Electrical Properties of 8mol% Yttria-Stabilized Zirconia Prepared by Spark Plasma Sintering Sealing Behavior of Visco-Elastic Composite Seals for SOFC Applications
by "Nielsen BookData"
