Manufacturing science and engineering I : selected papers from the 2009 International Conference on Manufacturing Science and Engineering (ICMSE 2009), 26-28 December, 2009, Zhuhai, China

著者

• International Conference on Manufacturing Science and Engineering
• Jiang, Zhengyi
• Zhang, Chunliang

書誌事項

Manufacturing science and engineering I : selected papers from the 2009 International Conference on Manufacturing Science and Engineering (ICMSE 2009), 26-28 December, 2009, Zhuhai, China

Edited by Zhengyi Jiang and Chunliang Zhang

（Advanced materials research, 97-101）

Trans Tech Publications, c2010

• :[set]
• Part 1
• Part 2
• Part 3
• Part 4
• Part 5

注記

Includes bibliographical references and index

内容説明・目次

内容説明

This book brings together the latest advances in, and applications of, manufacturing science and engineering. It comprises 976 papers, selected from among 3062 papers which were submitted by universities and industrial laboratories all over the world. All of chosen papers were subjected to strict peer-review.

目次

Committees Preface CHAPTER 1: Semiconductor Materials Manufacturing Blade Diamond Disk for Conditioning CMP Polishing Pad Three-Point Bending Test Behaviour of a QFN Semiconductor Package Structural and Optical Properties of Dy Doped ZnO Film Grown by RF Magnetic Sputter The Progress of Fixed Abrasive Wire Saws in the Last Decade Photocatalytic Analysis and Characterization of Zn2SnO4 Nanoparticles Synthesized via Hydrothermal Method with Na2CO3 Mineralizer An Optimization of Two-Steps Curing Profile to Eliminate Voids Formation in Underfill Epoxy for Hi-CTE Flip Chip Packaging The Crystal Structural Properties of Sputtered ZnO Films Containing Internal Stress The Comparison Research of Two Working Electrodes in Electrochemical Reduction of Silicon Tetrachloride Effect of Ca Content on Mechanical Properties of 4N Gold Wire for Quad Flat Nolead (QFN) Stacked Die Package Characterization of 0.5 m BiCMOS Gate Oxide Using Time Dependent Dielectric Breakdown Test Dynamic Analysis of Optical Brittle Crystal Slicing by Using Wiresaw CHAPTER 2: Precision Molding Processes On the Warpage in the Lower Case of Lead-Acid Batteries Effect of Forming Parameters on the Mechanical Properties of Thixomolding AZ91D Magnesium Alloy Analysis on Transmission Characteristics of New Axis-Fixed Cycloid Gear Research on the Key Technologies for New Large Dual-Platen High-Precision Clamping System CHAPTER 3: Materials Forming Analysis of Tension and Deformation Curvature in Strip Tension Levelling The Modulus Mensuration of Yada Model and the Microstructure Simulation of Casting AZ31 Magnesium Alloy Strip Shape Analysis of Asymmetrical Cold Rolling of Thin Strip Experimental Research on Coaxial Extrusion of GF/Pb Complex Wire Numerical Simulation of Push-Bending Process of Aluminum Section Profile The Effect of Entrance Temperature on Texture and Microstructure Development in Cold Mill Rolled 85/15 -Brass Numerical Simulation and Process Test for Cold Extrusion of Wheel Hub Bearing Rings Effect of Bonding Pressure on Transient Liquid Phase Bonding Joint Microstructure and Properties of T91/12Cr2MoWVTiB Finite Element Simulation of Backward Ball Spinning of Thin-Walled Tube with Longitudinal Inner Ribs On Spontaneous Austenite Recrystallization of Low Pressure Rotor Steel 26Cr2Ni4MoV Research on Intelligent Deep Drawing Technology of Sheet Metal New Methodologies for the Determination of Precise Forming Limit Curve in Single Point Incremental Forming Process A New Springback Compensation Method for Sheet Metal Bending Based on Curvature Correction Thermo-Mechanical Numerical Simulation on P91 Closed Upsetting Process Influence of Hot Working Conditions on Mechanical Properties and Microstructures at Weld Zone of the Ti3Al /TC4 Dual Alloy Study on Work Hardening Performance of Pure Shearing Fine-Blanking with Negative Clearance for ASTM-Gr.D and ASTM-1022 Steel Study on the Impact of Fine-Blanking with Negative Clearance on the Materials Microstructure and Hardness Influence of Isothermal Forging Temperature on Microstructure and Tensile Properties of Ti-5.8Al-4.0Sn-4.0Zr-0.7Nb-0.4Si-1.5Ta Near- Titanium Alloy Numerical Simulation on the Effect of Process Parameters for Incremental Sheet Forming Determination of Winding Tension in Manufacturing Strip Wound Die Study on Deformation Mechanism of Tube Hydropiercing An Investigation of Fineblanked Surface of Cold-Rolled 45 Steel Simulation and Analysis on Microstructure Evolution of Large Generator Retaining Ring during Multi-Fire Forging Preparation and Characterization of Well-Dispersed Nd1.6Eu0.4Zr2O7 Solid Solution and its Fluorescent Behavior Ultra-Fine Grained Fe-32%Ni Alloy Processed by Multi-Axial Forging Comparative Study of the Process Fracture between Fine-Blanking with Negative Clearance and Conventional Blanking The Influence of Integrated Strength on Bulging Cracking of Tailor Welded Blanks Advanced High Strength Steel Sheet Forming and Springback Simulation Improving Plastic Thermoform Quality with Uniform Heating Technology Numerical Investigation of Viscoelastic Flow and Swell Behaviors of Polymer Melts in the Hollow Profile Extrusion Process The Design Method of Punches and Dies for Progressive Die of Motor Core Based on Association Design Technology Solution of Singularity Points in Strip Rolling by Rigid Plasticity Finite Element Method Effect of Ultrasonic Wave on Melt Foaming Process of Aluminum Foam Study on the Differential Thickness Ratio Effect on Formability of TWB Based on Numeric Simulation Research on Stamping of Aluminum Alloy Hemispherical Components Based on Numerical Simulation and Experiments Extrusion Modeling of Solid Plug Flow of Co-Rotating Twin Screw Pulping Extruder Optimum Design on Trapezoidal Thread Parameters of Co-Rotating Twin Screw Extruder Research on Stamping Spring-Back Prediction for Car Body Panel Based on BP Neural Network Investigation on Thermomechanical Treatment of PM FGH4096 Superalloy Investigation on the Formability of Tailor-Welded Blanks Springback Prediction of Axial Symmetry Sheet Part Drawing Research of Geometric Parameters Related to TRB Uniaxial Tension Development of CAD System and Forming CAE of Porthole Extrusion Moulds for Hollow Aluminum Profile Study on the Dynamic Behaviors of X70 Pipeline Steel by Numerical Simulation Numerical Analysis on Hot Stamping of B Pillar Reinforcement of Automobiles Fatigue Life Prediction of Isothermal Forging Dies Based on Average Strain Method Hot Deformation Behavior and Hot Processing Map of P92 Steel Limit Pressure of Rupture Discs Found on Tensile Instability Condition The Effect of Isothermal Forging Parameters on the Microstructure and Properties of Ti-5Al-5Mo-5V-1Cr-1Fe Titanium Alloy Investigation of the Relationships between Billet Reheating and Semi-Solid Die-Casting The Forming Scheme of a Silencer Cover in Progressive Die Numerical Analysis and Optimization of Stamping Technology for Electrical Motor's Cover Plastic Deformation Characteristics Analysis in Rotary-Draw Bending Process of Thin-Walled Rectangular Tube Microstructure and Mechanical Properties of Heavy Gauge Plate by Vacuum Cladding Rolling Manufacture of a Seal Flange with E-Cross-Section Temperature Effects of ECAP and Annealing after ECAP on Microstructure of TA15 Alloy Study on Bending and Upsetting Forging 305 Marine Crankshaft Improvement of Hole Flanging Product Forming Process Using Finite Element Simulation An Analytical Solution to Metal Plane Problem in Terms of Orthotropic Anisotropy and Strain Hardening Numerical Simulation and Experimental Study on the Weld-Line Movement of Tailor-Welded Blank Spinnability of Semi-Continuous Casting 7A09 Aluminum Alloy Electromagnetic Field Simulation and Experiment of Electromagnetic Forming of Magnesium Alloy Tube Key Technology and Development on Side Pattern CAD/CAM on Mould for Auto Lamp Hot Deformation and Processing Maps of a High Strength Alloy Steel Effect of Process Parameters on Microstructures of 30Mn20Al3 Steel Experimental Study on Csf/AZ91D Composite Using Extrusion Following Vacuum Infiltration Method Synthesis of Intermetallic Ni3Al Alloy: Properties and High Temperature Oxidation Behaviour Key Technologies in the Design of a Vacuum Die Casting Mould for Aluminum Alloy Joints Finite Volume Simulation and Multi Parameters Optimization on Extrusion of Complex Aluminum Profile FVM Simulation of Large Deformational Aluminum Extrusion Process and Die Bearing Optimization Numerical Simulation and Evaluation of Local Thickness Increment in Ironing by Finite Element Method A New Manufacturing Method for a Screw-Threaded Fuel Filler Pipe Experimental Study on the Deformation of Oxide Scale and Friction during Hot Rolling of Stainless Steel 304L Mechanical Properties and Microstructures of Ferritic-Rolled High-Strength Interstitial-Free (IF) Steel Sheets Establishment and Application of Forming Limit Diagram of Multi-Gauge Laser Tailor-Welded Blanks CHAPTER 4: Materials Behaviour Effect of La and La+Sr on Structure and Properties of ZL101A Effects of Shot-Peening on Cr-Rare Earth-Boronizing at Low Temperature for Medium Carbon Steel Bifurcation and Chaos of a 4-Side Simply Supported Rectangular Thin Electro-Magneto-Elastic Plate in Many Fields Investigation on Low Cycle Fatigue Life of SC Notched Specimens Effect of Reactive-Al2O3 Addition on the Pore Size Distribution and Thermal Conductivity of Carbon Blocks for Blast Furnace The Research on Process of Deep Cryogenic Treatment for W4Mo3Cr4VSi HSS Drill Effects of Nb Doping on Dielectric and Ferroelectric Properties of Bi4Ti3-xNbxO12+x/2 Ceramics Statistical Analysis of the Effect of Na2CO3 as Additive on the Reduction of Vanadic-Titanomagnetite-Coal Mixed Pellets Study on Crack Retardation with the Consideration of Crack Surface Roughness by FEM Effects of Mg-Doping on Structure and Electric Properties of MgxZn1-xO:Al Ceramics Frequency Equations of Magneto-Thermoviscoelastic Surface Wave Probabilistic Crack Propagation Behavior of Railway B Grade Steel Microstructure and Mechanical Properties of Cast Ti25Nb3Mo3Zr2Sn Alloy Creep Behavior of an AZ91 Magnesium Alloy Reinforced with Aluminum Silicate Short Fibers The Effect of Precipitates on Anisotropy of Al-Li Alloys 2090 and 2090+Ce The Characteristics of the Magnetic Memory Signals under Different States for Q235 Defect Samples Dielectric Tunable Properties of Ba0.6Sr0.4TiO3 Thin Films with and without LSCO Buffer Layer Activated Carbon Fiber for Super-Capacitor Electrode Analysis of Fracture Failure of Diaphragm of Non-Contact Electronic Horn Surface Hardness Changes after Strengthening under Low-Amplitude Loads Compressive Response of UHMWPE/Vinyl Ester 3D Orthogonal Woven Composites at High Strain Rates Effect of Silica Sol on the Properties of Unfired Mullite Rollers The Study on Oxidation Resistance Properties of Ductile Cast Irons for Exhaust Manifold at High Temperatures A Plastic Zone Equation Based on Mean Yield Criterion Studies on Corrosion Behavior of Q235 Steel by Iron Bacteria in Sedimentary Water from Storage Tank Mutual Interaction of Two Rail Surface Cracks under Thermo-Mechanical Contact Loading Effect of Metal Powder on Blast Power of the Low Collateral Damage Ammunition Influence of Perlite Admixture on Pore Structure of Cement Paste Research on the Mechanism of Aging of Dual Phase Steel Produced by Continuous Annealing Strain-Induced Precipitation in Nb-Bearing Low Carbon Multi-Microalloyed Steel Influence of Plastic Deformation Degree on Microstructure and Mechanical Properties of the Magnesium Alloy ZK60 after T5 Treatment Simulation and Analysis during Conveyor Stop Process Based on AMESim A Study on the Characteristic of the Ultra-Thin Copper Bonding Wire Effect of Rare Earth Y Addition on the Properties and Precipitation Morphology of Aged Cu-Cr-Ti Lead Frame Alloy Study on Al-Doped ZnO Films Prepared by Magnetron Sputtering with Rapid Thermal Annealing Process A Study on Crack Propagation in Bi-Materials Investigation on Correlation between the Modified Criterion and the Glass-Forming Ability for Metallic Glasses Influence of Surface Friction Mismatch on Front End Bending during Plate Rolling Effect of Thinckness on Residual Stress Fields of Cold Expansion Hole Tribological Behavior of Irritation Cross-Linked UHMWPE under Dry Sliding Effect of Severe Plastic Deformation Technique on the Dissolution of ' Phase in Al-Cu Binary Alloy Abnormal Changes of the Rheological Property of Sn Melt Induced by Temperature Study on the Relationship between the Thermoelectric Potential and the Wear of YW1 Cemented Carbide Inserts The Elastic-Viscoplastic Field Near Mode II Dynamic Propagating Crack-Tip of Interface in Double Dissimilar Materials Study on Time-Correlated Leakage Predication Model of Nonmetallic Gaskets A Novel Poly(Ferrocenyl-Schiff Base) and its Charge Transfer Complex with Iodine A Numerical Method for Predicting the Young's Modulus of Ceramic Study on Amorphous Formation Ability of Al-Fe Alloy Liquids in Hot Dip Aluminizing Non-Conventional Approach for Deacidification of Fumed Silica Investigation of Nonequilibrium Dynamics of Nickel Film Excitated by Femtosecond Laser Microstructural Evolutions and its Influence on Properties of Super-Duplex Stainless Steel A Three-Phase Constitutive Model for TiNiNb Shape Memory Alloys Effect of Specimen Dimensions in Dynamic Torsion Testing Experimental Comparison of Fatigue Characterizations between TRIP and DP Steels Effects of Thermal Exposure on the Mechanical Properties and Microstructure Stability of an Al-Cu-Mg-Ag Alloy The Correlation between the Liquid Structure and the Viscosity of Sn-Cu Lead-Free Solders An Experimental Investigation on Static and Dynamic Fracture Properties of MgAl A Comparison of Macroscopic Fracture Surface and Crack Growth Rate of Ti-6Al-4V Study on Strain Solitary Waves in the Nonlinear Elastic Circular Rod The Stereoscopic Morphology of Martensite in Ferrous Alloys Fatigue Crack Growth Behavior in Fusion Zone of 16MnR Steel Weldment The Study of the Relationships between Material Properties and Welding Residual Stresses Research on Initial Discontinuity State of an Advanced Aluminum Alloy Rolling Alclad Sheet Material Constitutive Model in Machining 7050-T7451 by Orthogonal Machining Experiments Effect of Electrical Current on Wear Rate of Nano-Al2O3p/Cu Composite Dynamic Properties of Asphalt Binders Containing Fiber Modifiers Design and Characterization of Ultrahigh Strength Dual-Phase Steel with Low Ratio of Yield Strength/Ultimate Tensile Strength Microstructural and Mechanical Aspects of High Nitrogen Steels at Cryogenic Temperature The Calculation of Kinetic Parameters in Manganese Nitriding The Skin Effect in a High Pressure Die Cast Mg-9%Al Alloy Preparation and Characterization of Ba0.6Sr0.4TiO3 Ceramics Doped with Al3+, Ga3+, and In3+ Effect of Heat Treatment Process on Microstructure and Mechanical Properties of SWRS82B Wire Rod Research on Evaluation of Corrosion Grade Based on Image Processing Technique 3-D Finite Element Analysis of Bonded Joints under Impact Loading The Effect of Fillet Geometry on Stress in Weld-Bonded Joints Research on Heat Treatment Influence Factors on High-Pressure Cylinder Steel 30CrMo-M Resistivity-Temperature Feature of Ga36.5Sb63.5 Melt Effects of Secondary Dendrite Arm Spacing on Microporosity of A357 Alloy An Investigation on the Hydrogen Content in Al-12Si Alloy Melt The Oil Lubricated Sliding Wear Behavior of In Situ TiB2 Partical-Reinforced Al-10Sn Matrix Composites Effect of Lubricant on Surface Rolling Contact Fatigue Cracks Thermal Aging Embrittlement Evaluation of Nuclear Primary Pipe Steel by Ductile to Brittle Transition Test Effects of Al and Zn on the Microstructure and Mechanical Properties of Magnesium Alloys Study on Hot Plasticity and Microstructure of Mn18Cr18 High Nitrogen Austenitic Stainless Steel A Double-Parameter K~J Fracture Criterion for Epoxy Asphalt Concrete Test Methods for Mechanical Properties of Structural Adhesives Effect of Welding Method on Weld Defects of ADB610 Steel Experiment and FEM study on Uniaxial Tensile of SiCp/Al Study on Static Deformation Characteristics of Mental Rubber Material Effects of Coating on Interfacial Fatigue of Fiber-Reinforced Composites Characterization of Tensile Damage for 3D-C/SiC Composites by Acoustic Emission Tempering Resistance of a New Type of Tool Steels Used in Magnesium Die Casting Machine Influence of HLB Parameters of Surfactants on Properties of Magneto-Rheological Fluid Experimental and Numerical Evaluation of the Vibration Fatigue of Small Bore Pipe in PWR On Three-Dimensional Fatigue Crack Propagation under Constant Amplitude Loading Strain-Based Fatigue Test and Reliability Research of 42CrMo Alloy Steel Wear Behavior of Cr2O3/Cu Composite under Electrical Sliding A New Electromechanical Coupling Model for Piezoelectric Actuator Stress Relaxation Analysis of Polyurethane Foam Preloaded Structures Yield and Rheological Behaviors of Magnetorheological Fluids Effect of Rare Earth Oxide on Sintering and Crystallization of Fused Quartz Ceramic Materials Characterization of Hyperelastic Dielectric Elastomer Based on Biaxial Tensile Bench Effect of Compressive Deformation on Degenerate Pearlite Transformation in a Fe-C-Mo Alloy Study on Doping and Microwave Permittivity of SiC Powders The Hereditary Feature for Preferred Orientation in Ferritic Stainless Steel Sustainable Manufacturing Technology and Properties of Steel Slag Concrete An Efficient Sampling Method for the Actual Reliability of Engineering Calculation and Design The Analysis of the Distribution of the Failure Statistical Data Hydrogen-Adjacent Pipelines Penetration of Cone-Nose Projectile to the Laminated Composite Aluminum Alloy Foam Target The Thermal Characteristics of Invar 36 Alloy during Plane Grinding Creep Continuum Damage Analysis for a Pressurized Thick Wall Circumferentially Welded CrMoV Steel Pipe at 640 DegreesC Moving Crack in an Infinite Plate of Orthotropic Anisotropy FGMs under Anti-Plane Shear Effects of Die Temperature of SSS Die Casting on the Microstructure and Mechanical Properties of ADC12 Aluminum Alloy Strain Amplitude Dependence of Damping Capacity in High Damping Mg-Based Alloys Continuously Extending to Microplastic Strain Mechanical Properties of Ti-Doped DLC Multilayer by Pulse Cathodic Arc Deposition Application and Research on the Cold-Drawing Steel Wire Annealing Process under the Pulse Current Effect of Recessing in Bondline on Stress in Co-Axial Lap Joint Stress Distribution in a Piezoelectric Material with an Elliptical Hole Subjected to Remote Uniform Shear Mechanical and Electric Loads Morphology-Controlled Syntheses, Growth Mechanisms, and Optical Properties of ZnO Nanocombs/Nanotetrapods Investigation on Fatigue Limit Based on the Series Complicated Notches for Structural Steel CHAPTER 5: Casting and Solidification Microstructure Formation at Low Velocity during Directional Solidification of Pb-Bi Peritectic Alloys The Effect of Al-5Ti-1B and Combination Electromagnetic Field on Grain Evolution of Die Casting Commercial Aluminum A New Compound Phosphate Heat-Cured Foundry Binder Manufacture of the Wear Corrosion Resistance High-Cr Cast Iron Impeller Formation of Non-Dendritic Microstructure of Semi-Solid Magnesium Alloy by Introducing Gas Bubbles Homogenization Behaviors of Low Frequency Electromagnetic Casting and Direct Chill Casting 7050 Aluminum Alloy Description of Recalescence in Bulk Undercooled Alloys Study on Size and Microstructure of Complex Cavity Aluminum Alloy Castings Formed by Pre-Burying Copper Pipe Core A Compound Process Preparing Semi-Solid A356 Alloy Slurry Structural Transformation in Electric Pulse Modified Liquid Aluminum Effects of Low Frequency Electromagnetic Field on Hot Tear during Hot-Top Casting Process Effect of Withdrawal Rate on the Microstructures of a Single Crystal Ni-Base Superalloy Microstructure Evolution of Heavy Section Ductile Iron Influence of Sulfur on the Microstructure and Properties of High Nickel Austenite Grey Iron Study on Surface Reaction Layer of Titanium Cast with Al2O3-Based Investment Materials Effects of Magnetic Field on the As-Cast Structures of Dual-Ingot Low Frequency Electromagnetic Semi-Continuous Casting Reclamation of Green Sand Containing Hot-Box Resin Sand and its Application Effect of SDAS on Homogenization of Al-Si-Mg Casting Alloys An Investigation on the Impurities of Aluminum Alloy in Melt Furnace An Investigation on the Overheating of A357 Aluminum Alloy Casting of Aluminum Alloy Clad Strip Using a Vertical Type Tandem Twin Roll Caster Roll Casting of Al-25mass%Si Numerical Simulation and Application of Electromagnetic Stirring in Ansteel Mechanical Properties of Heat Treated 30CrMo Steel Produced by Compact Strip Production Heterogeneous Nucleation for AZ91 with In Situ Synthesis Al4C3 Secondary Phases Present in Spray Formed Al-10.5Zn-2.0Mg-1.5Cu Alloy Effect of Aluminum Content on Mechanical Properties of Cast Magnesium Alloy Sheets Fabricated by Twin-Roll Casting CHAPTER 6: Powder Metallurgy and Ceramic Forming Damping Characteristics of Biomedical Porous NiTi Shape Memory Alloy Preparation of Superfine Low-Melting-Point Metal Particles by Phase Inversion Method Preparation and Characterization of Ce-Doped Ba0.2Sr0.8TiO3 Ferroelectric Ceramics Tribological Behavior of Ti(C, N)-Based and Functionally Gradient Ti(C, N)-Based Cermets The Exploration on Synthesis of Calcium Aluminate and Fe-Si Alloys Using Red Mud and Aluminum Dross Equal Channel Angular Pressing and Torsion of Pure Al Powder in Tubes An Experimental Study of Metal Co-Injection Molding with Sequential Injection Creep Damage Analysis of Powder Metallurgy Material with Inclusion Preparation and Mechanical Properties of Al2O3/TiCN Sandwich Nanocomposite Ceramic Tool Materials Carbon Foams with High Compressive Strength Derived from Mixtures of Mesophase Pitch and Si Particles Study on Friction Properties of Cu-Based Friction Materials with Ni Coated Nano-SiO2 Particles Synthesis of -Al2O3 Platelets in Molten Salt for High Performance Ceramics Synthesis of High Nitrogen Stainless Steel Powders by High Energy Ball Milling and their SPS Compaction System Design for High Energy Rate Electromagnetic Powder Compaction Devices An Experimental Study of Fine Powder Comminution in a Dual Cone Impact Mill Research of Constitutive Relation of Metal Powder in High Velocity Compaction Research on Manufacturing Technology and Heat Transfer Characteristics of Sintered Porous Surface Tubes Thermoelectric Properties of Iron Disilicide Prepared by Field-Activated Synthesis Process Process Investigation for Purifying Hydrated Silica from Fly Ash by Acid and Alkali Combination Method CHAPTER 7: Surface, Subsurface and Interface Phenomena The Micro-Torsion Mechanism of Polarization Axis during Fabrication of Polarization Maintaining Fiber Devices Post-CMP Cleaning of Atom-Scale Planarization Surface of Computer Hard Disk Substrate Prediction of Surface Roughness Profiles for Milling Process with Fractal Parameters Based on LS-SVM Analysis of the Stress Invariants Criterions for I-II Mixed Mode Crack Initiation Angles Structural, Optical and Electronic Properties of Cu-Doped ZnO Films Synthesized by RF Magnetron Sputtering Study on the Mechanism of the Cobalt Leaching of Cemented Carbide in Triethanolamine Solution Effect of Non-Steady State Loading on Rolling-Sliding Contact Stress Effects of Lanthanum on Fe-25Cr Alloys under Cyclic Oxidation Research on Damping and Vibration Characteristic of the Large and Precision NC Rotary Table Stress Field of Semi-Infinite Interface Crack Tip of Double Dissimilar Orthotropic Composite Materials Debonding Analysis along a Softening FRP-Concrete Interface between Two Adjacent Cracks in Plated Beams Corrosion Resistance of Ni-Y2O3 Composite Coating Prepared by Electrodeposition under Ultrasonic Condition The Simple Model of the Oil Film Thickness between Piston Ring and Cylinder Influence of N2 Proportion on Mechanical Properties of SiCN Thin Films Prepared by DIBSD Research of Contact Pressure of an Elastoplastic Rough Body in Contact with a Smooth Rigid Plane A Study on Diffusion in Hot-Dip Aluminizing Experimental Study on Surface Roughness and Residual Stress by End Milling 69111-Stainless Steel Substrate Roughness Effects on Chromium Oxide Coating Adhesion and Wear Resistance A Three-dimensional Finite Element Method for Surface Effects Characteristics of Fretting Wear in a Press-Fitted Shaft Subjected to Bending Load Wavelets-Based Feature Extraction for Texture Classification Experimental Study on Fracture Behavior of UHTCC Overlay/Concrete Interfaces under Mixed-Mode Loading CHAPTER 8: Coatings and Surface Engineering Preparation of Iron-Oxide Coated Porous Ceramics Filter and Adsorption and Degradation on Methylene Blue Preparation and Characterization of Electroless Co-Ni Coated ZrO2 Powder for Microwave Absorbing The High Temperature Property of Ni/WC Infiltrated Composite Layer on Cast Iron Substrate The Microstructure of Polyaniline Coatings Electropolymerized on Pb Substrate in Aniline+Oxalic Acid Electrolyte Research on the Effects of Atomization on Different Liquid Dielectrics in a High Voltage Electrostatic Field Study on Vehicle Wheel Automatic Recognition Based on the Manufacturing Research of Characteristics of Ni-W-P Nanocomposites Containing CeO2 and SiO2 Particles The Microstructure and Properties of Coating from Mo2FeB2 Cermet on Surface of H13 Steel by Reactive Flame Spraying Novel Method for Improving Surface Performance of Rolling Bearing Raceway Gradient Characteristic of Functionally Graded Cemented Carbide Effects of Voltage on the Characteristics and Corrosion Resistance of Microarc Oxidation Coatings on Ti6Al4V Alloy Study on the Preparation and Alleviating Fretting Wear Property of Ni-Tl-B Coatings on Steel Effect of WC Grain Size on the Abrasive Wear Resistance of HVOF Spraying WC-Co Coatings Copper Multilayer Coating Prepared by Ultrasonic-Electrodeposition Nanostructured Surface Layers In Low Carbon Steel and Pure Titanium Induced By High-Speed Rotating Wire-Wheel Deformation Tribological Behavior of Molybdenum Alloying Layer on H13 Steel by Electrospark Deposition Technique Synthesis and Characterization of Nickel-Iron-Silicon Nitride Nanocomposite Wear Behavior Of Chromizing-Titanizing Coating Sherardizing and Characteristic of Zinc Protective Coating on High-Strength Steel Bridge Cable Wires Enhancing Steam Oxidation Resistance of Ferritic Steels through Formation of Nickel Aluminide Diffusion Coatings at Low Temperatures Microstructure and Wear Resistance of TiC+Cr7C3 Reinforced Ceramal Composite Coating Produced by PTA Weld-Surfacing Process Remanufacturing of High Temperature Ball Valve by Surface Engineering Technology Oxygen Evolution Kinetic Parameters of Electrodeposited Composite Inert Electrodes Pulse Electrodepositon of Ni-W-P-CeO2-SiO2 Composite Coatings Fabrication of Bionic Silicon Surfaces with Lotus Effect and their Micro Tribological Performance Effect of Diffusion Treatment on High-Temperature Oxidation Resistance of Multi-Arc Ion Plating Al Films on TiAl Alloy Temperature Field Simulation for Aluminum Alloy Surface Modification by Scanning Electron Beam Synthesis and Characterization of NiCoFeCrAl3 High Entropy Alloy Coating by Laser Cladding Optical and Mechanical Properties of Silver Film on Glass Substrate Control-Steps and Influence Factors of SiO2 Electrodeposition Process with Zn Coatings Amorphization of Fe-Ni Based Alloys by Laser Cladding and Remelting The Optical Properties of Sputtered ZnO Films Influence of Laser Surface Texturing Distribution Patterns on the Hydrodynamic Lubrication Finite Element Analysis of the Temperature Field and Strain Field of Coating Rod in Friction Surfacing A Statistical Model for the Joint Distribution of Droplet Size and Charge Density in an Electrostatic Spray Cu-Ni-Ti Composite Diffusion Coating of the Al2O3 Ceramic Surface and its Joining Mechanism Preparation and Properties of the Ni3P-TiO2 Coating on Carbon Steel Influence of Rare Earth on the Properties of H13 Steel by the QPQ Salt-Bath Treatment Anti-Wear Property of Self-Repairing Mineral Particles as Grease Lubricant Additives on the Metal Friction Pairs Fabrication of n-SiO2 Reinforced Al2O3 Composite Coatings on 7A52 Aluminium Alloy by Micro-Arc Oxidation Brush Plated Multilayered Cu/Ni Coating from a Single Electrolyte and its Fretting Wear Behaviors Influence of Ultrasonic Peening on Wear Resistance of U70 Rails Surface Hardening of Spot-Welding Copper Alloy Electrode for Zinc Coated Steel Structure and Oxidation Behavior of Gradient Zr/ZrN/Zr Diffusion Barrier on the Ni-Based Superalloy by Arc Ion Plating The Process of Electroless Plating Ni on the Surface of Carbon Fibers Microstructure and Corrosion Resistance of Free-Sprayed Ni60 Coating Prepared by High Frequency Induction Heating Adaptability Study of an Ideal Linear Elastic Constitutive Model for a Plasma Sprayed Ceramic Thermal Barrier Coating The Influence of Laser Hardening on the Microstructure and Wear Resistance of Disk Opener Investigation of Nano Composite Coating on Aluminum Alloys Treated by Plasma Transferred Arc High Temperature Wear Behaviors of Electro-Brush Plating Ni-P Coatings Microstructure and Wear Properties of Laser Clad TiN/Co-Based Composite Coating Effect of Rare Earth Addition in Plasma Nitriding on Microstructure of Chromium Electro-Plating Microstructure and Reciprocating Sliding Tribological Performance of Micro-Arc Oxidation Coating Prepared on Al-Si Alloy Erosion Wear Behavior of Coatings with Growth Defects Produced by Ion Beam Enhanced Pulsed Filtered Vacuum Arc Deposition Rotational Fretting Wear of Ion Nitrided Medium Carbon Steel Microstructure Characteristic of Laser Cladding Ceramic Layer on High Cr Cast Steel Surface Oxidation Study of APS Thermal Barrier Coatings in Elevated Temperatures Growth Behaviour of ZnO on Si (100) and Platinum Coated Glass Substrate from Aqueous Solution Influences of Different Calcinations Ambience on Phase Composition and Morphologies of Ceramic Coatings on Ti Alloy by Micro-Arc Oxidation Effect of Sulfurizing Temperature on Formation of Coatings Produced by Nitriding-Sulfurizing Composite Treatment for Ti-6Al-4V Alloy Research on In-Flight Property of Particles in Plasma Spray Forming CHAPTER 9: Composite Materials Numerical Modeling of the Fracture Process of a Three-Unit All-Ceramic Fixed Partial Denture Synthesis of TiO2/Polymer Composite Microspheres Using Functional Porous Polymer Particle as Substrate Vibration Suppression of Flexible Beams Using MR Elastomers Study on Activated Carbon /Polyaniline Electrode Materials for Supercapacitorsts Synthesis of (TiC)pNi/TiAl/Ti Graded Material via Field-Activated and Pressure-Assisted Combustion Process Characteristics and Elastic Modulus Evaluation of Pd-Nafion Ionic Polymer-Metal Composites Reasearch on Heat-Shocking Resistance of SiC(w)/ZrO2-MoSi2 Ceramic Composites Preparation and Damping Capacities of the NiTiSMA/FC Composites Effects of Technological Parameters on Microstructures of Semi-Solid Magnesium Matrix Composites The Preparation and Photocatalytic Activity of SWNTs Doped ZnO/TiO2 Compound Films Tensile and Bending Strengths of TR-30s Carbon Fiber Three Dimensional Braided Composites at Different Temperature The Study of Mechanical Properties of Structural Lightweight Concrete Reaction Mechanism of an Al-TiO2 System Microstructure Evolution and Mechanical Behavior of CNTs/ AZ31 Magnesium Alloy Composites Processed by Equal Channel Angular Pressing High Strain Rate Superplastic Deformation Behavior of TiNP/2014Al Composite Effects of Al Content on Phase Composition of Zr-Al-O-N Composites Preliminary Study on VGCF Reinforced Cement Composites Experimental Investigation on Drop in Tensile Performance Index of Carbon Fiber Composite in Use Effects of Nano-Al2O3 Additions on Microstructures and Properties of WC-8Co Hard Metals Preparation of NiTi/NiTiNb Laminated Alloys by Vacuum Brazing Tic Particle Reinforced Iron Based Composite Coating by Submerged-Arc Welding Added Alloy Powder Parametric Modeling Method for Composite Microstructure Virtual Testing Manufacture and Tribological Properties of C/C-SiC Brake Composites Fabricated by Warm Compacted In Situ Reaction Influence of Nanosilica/Polyurethane Composite Coating on IR Effectiveness and Visible Light Transmission Properties of Polyethylene Design, Production and Mechanical Property of White Engineered Cementitious Composites Preparation of TiO2-g-Polystyrene Nanosphere and its Application in Toughening PS Matrix Friction and Wear Behaviors of Si3N4 Sliding against M50 Bearing Steel in Vacuum Effects of Surface Modification of SiC Nanoparticles and Preparation Process on Microstructures of SiCp/A6061 Alloy Matrix Composites Transverse Elastic Deformation Behavior of Aligned Fiber Bundles under Bulk Compressive Pressure and Longitudinal Stress Synthesis and Mechanical Property Evaluation of Ti-TiAl Metal-Intermetallic Microlaminate Composite Interfacial Treatment of Multi-Layer Woven Silk Reinforced Epoxy Composites Fracture Characteristics for Crack Tip near the Interface between Steel and Concrete in Composite Structures Energy-Based Debonding Model for Steel-Concrete Composite Structures Study on Figuration Techniques of Grades Extrusion for Making Metal Rubber Material Analysis of Mesoscopic Interfacial Mechanics of RC Beams Strengthened with FRP Comparative Research on the Effects of the Self-Healing Microcapsules on the Modal Properties of Composite Brake Study on TiCp/Al Master Alloy in Magnesium Matrix Composites Copper-Based Electronic Materials Prepared by SPS and their Properties Research on Methods for Elastic Stiffness of Multi-Ribbed Slab Structure Experimental Research on Low-Velocity Impact Properties of 3D Braided Composites A Finite Element Model to Simulate the Cutting of Carbon Fiber Reinforced Composite Materials Synthesis and Catalytic Activity of Composite Materials TiO2/Ti-Al-MCM-41 by Chemical Vapor Deposition (CVD) Study on Reaction Synthesis Mechanism of TiC-Al2O3 Particle Co-Reinforced Aluminum Based Composites Effect of Hollow Structure on the Electromagnetic Interfering (EMI) Shielding of Aluminum-Cenospheres Composites The Numerical Simulation of Co-Curing Process for AGS Plate The Characteristics of Multilayer Thin Films Deposited with Metal Thin Films (Ag, Al, Cu) Glass Fiber Permeability Using the VARTM Process Microscopic Analysis of Flow and Prediction of Effective Permeability for Dual-Scale Porous Fiber Fabrics The Higher Order Asymptotic Fields for a Anti-Plane Crack in a Linear Functionally Gradient Material Mechanical Evaluation of the Production of Bamboo Charcoal/ Stainless Steel Complex Yarns and Knitted Fabrics Analyses on the Manufacture and Physical Properties of Electromagnetic Shielding/ Far Infrared Ray Nonwoven Mechanical Analyses of Repeatedly Processed Polypropylene/Carbon Fiber Composite Plates Manufacturing Technique and Physical Property of Metal Wires/ PP Nonwoven Selvedges Complex Ply Yarns and Knitted Fabrics Manufacturing Process of Sound Absorption Composite Planks The Study on the Surface Morphology of Al/SnO2-Sb2O3 or SnO2-Sb2O3-MnO2/PbO2 Electrode Material CHAPTER 10: Machining Research on the Surface Change of the Large Optic Plane Wafer In the Fast Polishing Process Effects of Tool Geometry and Workpiece Hardness on Surface Roughness in Finish Hard Turning of AISI 440C Transient Dynamic Analysis of the Matching of Lengthened Shrink-Fit Holder and Cutter in High-Speed Milling Cutting Mechanism of Multi-Tooth Tool for Manufacturing Metal Fibers Performance Evaluation of Minimum Quantity Cooling Lubrication Using CBN Grinding Wheel Analytical Modeling of Workpiece Surface Temperature Rise in Machining Theoretical Analysis and Experimental Investigation into Hydrodynamic Pressure and Coolant Lift Force in Flood Delivery Grinding Research on Surface Machining System for Light Metal Thin-Walled Parts Based on Spherical Coordinate Research on Wear Mechanisms while Turning Titanium Alloy TC4 Study on the Stability of High-Speed Milling of Thin-Walled Workpiece Enhancing Machined Parts Surface Quality by Using a Composite Material for Tool Body in Turning Experimental Investigations of Tool Wear Mechanisms in Machining 1Cr18Ni9Ti Stainless Steel Experimental Study of Improved Tool in High Manganese Steel Drilling Determination of the Anti-Chatter Weak Component on a Machine Tool The Friction Coefficient and Self-Organization Feature on Rake Face when Turning Hardened Steel with Coating Tools Study on Causes of Material Plastic Side Flow in Precision Hard Cutting Process An Experimental Investigation of Cooling-Air Grinding Performance Design and Motion Simulation of Floating Die Polishing Device Microscopic Examination of Primary Shear Zone in High Speed Machining of Hardened High Strength Steel Crater Wear Modeling in Conventional Speed Machining Vibration Analysis Based on AR Trispectrum in Milling Process Study of Grinding Method of Twist Drills The Influence of Spray Characteristics on Surface Roughness in Minimum Quantity Lubrication Turning A Study on Cutting Force in Micro End Milling with Ultrasonic Vibration Acoustic Emission and Vibration Analysis of Process of Hard Dry Milling Failure Mechanisms of Carbide Tool in High Speed Milling of Inconel 718 Experimental Study on Relation between Tool Wear and Grinding Force for Shaping Diamond Tool Experimental Study on Milling Force of High-Temperature Alloy GH536 Finite Element Simulation of Ultrasonic Vibration Orthogonal Cutting of Ti6Al4V Friction Torque of Rotating Hydraulic Cylinder with Deep Circular Groove Oil Film Face Seal Research on Precision Grinding System and Key Technology Based on PMAC-PC Research on Chatter Suppression in Machining Thin-Walled Components Based on Rigidity Optimization A Bioreactor for a Pulsatile Circulatory Culture System Study on Metals Behavior Subjected to Cyclic Loading Based on Bauschinger Effect of Reversible Fine Machining Sequence Analysis of Cutting Forces in Precision Turning Based on Oblique Cutting Model A Technical Study of Hole Drilling in Ceramics/FRP Laminate Composite Components Design of an Ultrasonic Vibration Deep-Hole Honing Device Experiment and Theory of Cutting Forces for Cemented Carbides Based Self-Lubricated Tool Embedded with Solid Lubricants Study on the Cutting Mechanism of Remanufacture Deposited Materials in the Impactive Condition Research on Tool-Chip Friction during Ti6Al4V Milling Process with Different Cooling/Lubrication Methods Role of Chip Serration Frequency in Chatter Formation during End Milling Operation of Stainless Steel Prediction of Flank Milling Forces in Ruled Surface Impeller Machining Nonequivalent Milling of Roller Gear Cams Based on Approximation Method of Offset Surface Study on Precision Grinding of Involute Cams on a Double-Disc Device Trajectory Interpolation in CNC Grinding of Indexable Inserts A Soft CNCS on Windows-XP Four-High Mill with Statically Determinate Characteristics of Micro Displacement of the Components CFD Research on Aerostatic Bearing with Tangential Supply Holes Research on Plastic Rolling Forming Process of Plate-Fin by Numerical Simulations and Experiments SSA Based Decomposition of Tool Position Trajectory for Diamond Turning of Freeform Optical Surfaces Assessment of Machining Characteristics of Austempered Ductile Iron Influence of Radial Depth of Grinding and Finishing Process on Surface Residual Stresses in Grinding AF1410 Ultrahigh Strength Steel Research on Surface Roughness Prediction Model for High-Speed Milling Inclined Plane of Hardened Steel Cutting Forces and Tool Wear Patterns in Five-Axis Milling Fe-Based Super Alloy with Bull-Nose End Mill Research on Design and Application of Control System in Machine Tool Modification Tool Wear Investigation on Dry Electrostatic Cooling in Turning Titanium Alloy Ti6Al4V Effect of Burnishing Process on Surface Characteristics of Particulate Reinforced Iron-Base Composites Experimental Research on Turning Vibration Deduction with Intelligent Material Based on LabVIEW Machinability Prediction of Workpiece Material with a Diagraph Method Thermal and Shear Characteristics Study of Various Mechanical Polishing Materials Effect of Tool Inclination Angle on Surface Quality in 5-Axis Ball-End Milling Non-Special Dressing Electrode Experimental Study on ELID Grinding The Grinding Head Design in Non-Circular Gear Grinding Teeth Based on the Planar Regions Interference Inspection An Investigation on the Heat Partitioning in Grind-Hardening The Control Algorithm of Ultrasonic-Magnetorheological Combined Finishing for Rotary Symmetrical Aspheric Surface Vacuum Dehumidifying Dryer for PET Chips Failure Mechanism of Twist Drill in Vibration Drilling of Duralumin Effects of Grinding Wheel Vibration on Surface Quality of Axisymmetric Aspheric Lens Study on the Modeling Method for Finite Element Analysis of Chip Formation Process Study on Helical Drill Point Grinding with a Biglide Parallel Grinder A Mathematical Model of EEBP for HSM Surface Quality Prediction Research on Safety Decline of High Speed Milling Cutter CHAPTER 11: Nanomaterials and Nanomanufacturing CMP Behavior of -Alumina-g-Polyvinylpyrrolidone Composite Abrasive on Hard Disk Substrate Preparation of Maghemite-Silica Nanocomposites Using Sol-Gel Technique Biomolecule-Assisted Synthesis of Ribbon-Like Sb2S3 Nanostructure Low Temperature Synthesis of TiO2 Nanorods with Tunable Aspect Ratios from Ti and NH4Cl Powders Preparation of Novel Silica Nanoparticle/Polystyrene Composite Microspheres in a Pickering Emulsion Strain Gradient Plasticity Theory Based on Dislocation - Controlling Mechanism for Nanocrystalline Materials The Improvement of Generalized Particle Method for Nano-Materials Molecular Dynamics Simulation Refinement of Microstructure in Steels through Thermomechanical Processing Equivalent Continuum Models for the Simulation of Mechanical Properties of Carbon Nanotube by Global-Local Homogenization Method Preparation of Manganese Zinc Ferrite Nanoparticles by Polymer Matrix Templated Synthesis Preparation of Y2Ti2O7 Nanocrystal by Sol-Gel Method and its Characterization Self-Assembly of Cuprous Oxide Micro/Nanostructures by Photo-Reduction Method A Dimensional Analysis Model for Geometric Size Effects of Single Crystals Fabrication of Gold Cap-Shaped Nano-Particle Films and Sensing Device for Bioanalytical Application Development of Ultra-Precision Grinding Process for Aspheric Surface Based on Feed Rate Controlling and Error Compensation Methods Effect of ZnO Nanoparticles on the UV Light Fastness and Climate Resistance of PVC Film Structure and Magnetic Properties of Carbon Encapsulated Co Nanoparticles Prepared by the Pyrolysis of Mixture of Sucrose and Cobalt Nitrate Fe-Based Micro- and Nanocomposite Coatings Produced by Amorphous Alloy Crystallization Based on Electrospark Deposition Preparation and Photoelectric Performance of Eu3+-Doped Porous TiO2 Thin Film Electrode A Hybrid Pso and Shuffled Complex Evolution Algorithm for Order Assignment Problem in Holonic Manufacturing System Effect of Combined Shot Peening Process for Surface Nanocrystallization Method on Fatigue Strength of TC4 Experiment on Nano-Sized Activated Carbon/Zn-MnO2 Electrode Material CHAPTER 12: Biomedical Manufacturing The Effect of Precipitates on the Bio-Corrosion Property of As-Cast Mg-Zn-Y Alloys Study on Biomedical Resources of Benzene/Alcohol Extractives of Eucalyptus Leaves by GC/MS Effect of Solution Treatments on the Microstructures and Mechanical Properties of Mg-2Zn-0.8Mn-0.5Ca Alloy Residual Stresses in Fabrication of Core-Veneered Ceramic Prostheses Fabrication of PLLA Scaffolds by Low-Temperature Deposition from a Ternary Polymer-Solvent System Evaluation of Electrospun Poly (Vinyl Alcohol) (PVA)/Gelatin Nanofiber Membrane and Biocompatibility Evaluation of the Surface of PLA/ -TCP Powder Complex Braid Dissolution Resistance of Bovine Teeth-Derived Hydroxyapatite Sintering and Mechanical Property of Tuna Bone-Derived Hydroxyapatite Preparation of CaCO3-Containing Geopolymers for Green Concrete Efficient Machining of Artificial Hip Joint Components Effect of Water Glass on Compressive Strength of Aluminosilicate-Based Geopolymer CHAPTER 13: Environmentally Sustainable Manufacturing Processes and Systems Effect of LPG Injection Methods on Engine Performance High Intensity Glassed-Block Was Prepared by Fluid Cinder Simulating Production Lines of Recycling WEEE Products in eM-Plant Waste Beverage Containers Automatic Green Recycling Technique Based on the Optical Image Inspection The Theoretical Analysis and Experimental Study on Heat-Transfer in Cryogenic Pneumatic Mist Jet Cooling Experimental and Theoretic Research on Solar Power Membrane Distillation A New Type of Cooling-Air Generator for Cooling-Air Grinding Process Parameters Optimization for Green Manufacturing of Laser Cladding Based on Artificial Neural Network An Automatic Shake Mechanism for the Biomass Pyrolysis Feeding The Adaptive Blade Design and Evaluation of Wind Turbine A Wireless Solution of Distributed Monitoring and Control System in Optical Aspheric Grinding Study on the Performance and Biodegradability of Three Kinds of Biodegradable Dishware Exploration and Application of Process Approximation Method on Cleaner Process Evaluation A Method of Multi-Environmental Spatial Scales Division in LCA Based on Chinese Region-Specific Experimental Study on Heat Transfer Characteristics of Apparatus for Recovering the Waste Heat of Blast Furnace Slag Feasibility Study for the System of Coal Gasification by Molten Blast Furnace Slag Fluid Clamping Devices Based on Area Effect Stroke Amplifier Driven by Shape Memory Alloys Wires Study on MQL in Point Grinding Process for Green Manufacturing Vibration Characteristics of Ni Thin Film Diaphragm by Acoustic Wave Study on Tool Wear of Cutting Ti-6Al-4V with Water Steam as Coolant and Lubricant in Green Machining Modification of Pellet Materials by Low Temperature Plasma H-Infinity Robust Control Methodology of Multi-Variable NCSs Evaluating Process Design through Quality Function Deployment for Environment Adaptive Fuzzy Control of Cutting Temperature Based on Cutting Fluid in High-Speed Machining CHAPTER 14: Manufacturing Process Planning and Scheduling Novel Non-equidistant Optimum GM(1,1) Model with Modified nth Component be Taken as Initial Value and its Application to Metal Cutting Study on an Inventory Decision Model in an Assembly System Design and Study of Multi-Function Asphalt Mixture Shear Apparatus Similarity-Based Integrated Scheduling of Machining Processes in the NC Resource Grid Velocity Control Method for Continuous Short Line Segment High-Speed Machining Based on Transition of Parametric Spline Research of Sequencing Working Steps Method for Box Part Dynamic Reentrant Scheduling Simulation for Assembly and Test Production Line in Semiconductor Industry The Conjugation of the Hardened and Grinded Worm Gear An Effective Immune Based Approach for the No-Wait Flow Shop Scheduling Problems with Multiple Machines A Production Scheduling Method for Bell-Type Batch Annealing Shop Filtered Beam Search Based Flexible Job Shop Scheduling Problem with Transportation Time A Symbolic OBDD-Based Algorithm for Assembly Sequence Planning An Improved Genetic Algorithm for Multi-Objective Flexible Job-Shop Scheduling Problem Optimization of Printed Circuit Board Assignment and Component Allocation in Assembly Line Study on the Scheduling Problem of Powder Painting Production - A Case Study An Optimization Approach for Semiconductor Wafer Fabrication Scheduling Problem Modeling and Simulation of Re-Entrant Semiconductor Wafer Fabrication Lines with PM Using GSPN Improved Adaptive Genetic Algorithms for Job Shop Scheduling Problems A New NURBS Tool Path Generation Algorithm for Precise Sculptured Surface Machining Research on Dynamic Reconfigurable Manufacturing Process Framework Based on MDA Application of Grey Correlation Analysis on Tool Selection CHAPTER 15: Meso/Micro Manufacturing Equipment and Processes Design and Analysis of Big-Character Printer Neural Network Based Computer-Aided Process Design System for Wire Bonding Quality Improvement Analysis and Stress Optimization Design of an S-Shaped Micro Spring Design and its Experiments of Micro Electrochemical Machining System Research for Combustor Based on Micro-Thermoelectric Generator Device Study on Micro-Displacement Stage Driven by Piezoelectric Actuator Application of Ultrasonic Vibration Shoe Centerless Grinding Technique to Micro-Scale Parts Fabrication Ultra Precision Surface Grinding for Large Scale Non-Axisymmetric Aspheric Lens Experimental Study on Viscous Dissipaition of Polymer Melt in Micro-Channels Study on the Manufacturing Method of the Biomimetic Drag Reducing Morphology Replication Mold Laminated Photoresist Sacrificial Layer Process for 3-D Movable Suspension Microstructures in LIGA-Based Surface Micromachining Numerical Simulation and Experimental Investigation of Tool Edge Radius Effect on Micro-Cutter Wear in Micro-End-Milling Process Experimental Study on the Cutting Performance of Ultra-Precision Micro Milling Machine CHAPTER 16: Modeling, Analysis, and Simulation of Manufacturing Processes Numerical Simulation and Optimization on Casting Technique of HT200 Flywheel Experimental Research on the Vibration Characteristics of Flexural Vibration Disk Production Logistics Simulation System for a Rail-Beam Plant Based on Component Technology Numerical Simulation and Experiment of Aluminum Sheet Metal Springback in New Quenching State The Research of Structural Optimization on Diesel Engine Injection Nozzle Die-Pressing Parameters Optimization Based on FEA Dynamic Simulation of Position Servo System of Pneumatic Manipulator Based on AMESim and Simulink Finite Element Simulation of Temperature Field in Fused Deposition Modeling The Study on Suppression of Dimples in Digital Multi-Point Stretching Process Flexible Multibody Simulation Approach in the Analysis of Friction Winder Prediction and Analysis of Forged Workpiece's Precision in Hydraulic Press Based on BP Neural Network and Genetic Algorithm Analysis of Assembling and Working Stress of Compound Rings High-Pressure Vessel of 5GPa Virtual Machining on Helical Bevel Gear with New Type Heavy Duty Helical Bevel Gear Milling Machine Tool Effects of Opening Hole Geometric Parameters on Hole-Edge Stress Field of Plates According to a Complex Variable Function Model Simulation and Optimization on the Injection Molding for Auto-Bumper Simulation Study on Magnetic Field Characteristics of High Magnetic Field Intensity Permanent Magnet Magnetic Filter The Application of MR Fluid Damper to the Vibrating Screen as the Enhance of Screening Efficiency Nonlinear Dynamic Behaviors and Bifurcation of Symmetrical Rotor System Supported by Self-Acting Gas Jounal Bearings Molecular Dynamic Simulation on Mechanism of Ultrasonic Wire Bonding in Electronic Package Higher Order Harmonic Wave and its Effect on Thermosonic Bond System CSP-Driven Schedule Optimization in NC Equipments Grid Considering Complex Correlated Process Flows The Fatigue Life Prediction of Pistons Based on the Cumulate Damage Influence of Preparing of Specimen on Internal Stress Measurement of Aluminum Alloy Thick Plate An Adaptive Local Meshfree Updated Lagrangian Approach for Large Deformation Analysis of Metal Forming Hydroforming Simulation and Experiment on Al 5083 T-Shapes Research on the Fault Diagnosis of Trenchless Drilling Pneumatic Impact Device Based on Grey Relational Theory Study on On-Machine Measurement of Rotating Tools Based on Image Processing The Series-Parallel Robot Coordinates Polishing System Based on the Multi-Agent The Studies on Influence of Assembling Technologic Parameters on Dynamic Characteristic of Sleeve Structure The Drum Height Detection Model of the Shearer Cutting Memory Program Control Collection Mode Optimization of Casting Dust Based on TRIZ Analytical Model of Thermal Stress for Encapsulation and Service Process of Solar Cell Module Impact Studies on the Setting Styles of Stiffened Board to the Ultimate Strength of Tubular K-Joints Collaborative Manufacturing Resources Configuration Based on Summary Process Routes Study on Indexable Inserts for Gear Gasher Dynamic Decoupling Control of Electro-Spindle Supported by AC Hybrid Magnetic Bearings Based on Neural Network Inverse Method Strength Analysis of Coiled Tubing in the Injector Mathematical Model for Closed-Form Solution of Parameters of Cylinder Exhaust Port in Variable-Stroke Engine A Wavelet-Based Finite Element Method for Modal Analysis of Beams Digital Manufacturing System of Aircraft Wing Integral Panel Numerical Simulations of the Fluid Flow and Heat Transfer during a Solidification Phase Change of a Polymer in a Die Cause Analysis of Longitudinal Cracks in Closure Segment of an Extra-Large Bridge A Simplified Method Study of Aluminium Alloy Fatigue Crack Tip Parameters Computed by Elastic-Plastic Finite Element Model The Manufacturing Resource Modeling of Multistage Manufacturing System Based on the Capacity Manufacturing Unit The Experiment Research of Continual Extension of Surface Crack Effects of the Gear Tooth Modification on the Nonlinear Dynamics of Gear Transmission System Design and Manufacture of a New Large-Scale Three-Dimensional Geomechanics Model Test System The Numerical Simulation of Air Bulge Forming of Profiled Can Two Dimensional Vibration-Assisted Micro-Milling: Kinematics Simulation, Chip Thickness Computation and Analysis MATLAB-Based Kinematic Analysis on Mechanisms of Multifunctional Wheelchair Hydraulic Performance Research of a Fixed Fire Water Monitor Effect of External Magnetic Field on the Flow and Heat Transfer in DC Arc Plasma Torch Design and Jet Characteristics Study of a Liqumatic Fire Water Monitor with Self-Swinging Device Flex Gradient Optimization on Stiffened Steel Plate of Profiled Plate Rubber Support 3D Loading Path-Generating Method for FEM Simulation of Incremental Sheet Metal Forming Process The Study on Vibration of Marine Riser under Deep Water Vibration Isolation Study on Coupled Vibration of Load Floor Caused by Iron Ore Pelletizing Machine on it Constraint Reaction Forces and Lagrange Multipliers in Multi-Body Systems Simulation of Failure in the Refractory Lining of Coke Dry Quenching Modeling Method of Crawler Crane Based on Open Source Engines A FEM Formulation for Flexible Multi-Body System Dynamic Analysis Motion Planning of Tomato Harvesting Manipulators with 7 DOF Research & Realization on Neural Network for Forecast of AM Automatic Logistics Information-System Simulation Based Model Experimentation with Minimum Solving Strategy Study on Cost Minimization of Auto Engine Product Warranty Chain Pressure Pulsation Analysis of Aircraft Hydraulic Power Pipelines System The Research on Milling Temperature and Heat Deformation of Tool in Virtual Numerical Control Simulation Study on the Formulas of the Dog-Bone Shape of Edger Rolling in Hot Strip Mill Sticking Analysis of the Bistable Inductive Micro-Switch Multi-Scale Numerical Simulation of H62 Brass for Hot-Extrusion Process The Function Simulation of TBM Based on Virtual Reality Finite Element Analysis of Pressure Coiled Forming Process to Taper Weld Pipe Effect of Process Routing on Machining Deformation for Multi-Frame Double Sided Monolithic Components Determination of Expanding Pressure of Hydraulically Expanded Tube-to-Tubesheet Joint Three-Phase Power Factor Correction Converter Based on One-Cycle Control in Aircraft Electric Power System A Novel Multiple RBF-NN Model for Rolling Force Prediction Based on Anti-Aliasing Wavelet Analysis The Stiffness Analysis and Modeling Simulation of Ball Screw Feed System Analysis of the Performance for a Group-Annulus Type Oil-Fired Boiler Effect of Diesel Nozzle Geometry on Internal Cavitating Flow A Novel Boundary Extraction Algorithm on Triangular Meshes of STL Model Influence Factors on Finishing Temperature of Plate Rolling Automatic Solder Joint Defect Classification using the Log-Gabor Filter Numerical Analysis of Grinding Fluid Field in Grinding Study on Prediction of Machining Distortion for Titanium Alloy Aircraft Monolithic Component by FEM Strip Profile Control in Asymmetrical Rolling by FEM Modeling Formation Mechanism and Simulation of Oxide Film in Electrodeless ELID Grinding A Framework of Cooperative Design for Aspheric Glass-Lens Mold Prediction and Prevention of Overburning Structure during Hot Processing of Chromium Forged Steel Analytic Modeling of Rolling Force during the Hot Rod Rolling of Multiple Alloying Steels Simulation of Thermal Deformation for Spindle of Machine Tool Crawler Cranes Modeling Method Based on OGRE Numerical Simulation of Double Rollers Clamping Spinning Process for Flanging Nonlinear Numerical Optimization Design Applied to Wall-Thickness of Welding T Shaped Connecting HDPE Tube On the Control System for Blank-Holder Force in Deep Drawing Based on Self-Tuning Fuzzy-PID Controller A Parallel Numerical Study of Transient Heat Transfer and Fluid Flow of Weld Pool during Laser Keyhole Welding Temperature and Stress Analysis in Micro-Cutting of Ti-6Al-4V and Al7050-T6 A Finite Element Analysis for the Characteristics of Cutting Parameters in 3D Oblique Milling Process Simulation and Experimental Investigation for the End Milling Process of 7075-T7451 Aluminum Alloy Research on Machining Simulation System for Optical Free-Form Surfaces The Algorithm of Acoustic Location for Boiler Tube Leakage Simulation of Compressive Strength of SiC Foam Simulation of Aluminium Foam Compressive Properties Moment Stability of Stochastic Regenerative Cutting Process Simulation of Microstructure Evolution for Two-Phase Ceramic Tool Materials at Different Duration Time An Integration-Based Stochastic Finite Element Method Optimization of Surface Roughness Based on Multi-Linear Regression Model and Genetic Algorithm A New Ultraprecision Machining Method with Softness Abrasive Flow Based on Discrete Phase Model Research on Precision Forming Technology of Car Steering Knuckle Finite Element Analysis on the Roll Milling Process of Twisted Oblate Tube Mechanical Analysis on the Inner Surface Crack of Modified 9Cr-1Mo Seamless Steel Tubes Rolled by Mandrel Mill Finite Element Simulation of the Effects of Mould Angle on the Equal Channel Angular Pressing for Al-Zn-Mg-Cu Alloy Simulation of Void Defect Evolvement during the Forging of Steel Ingot Research on the Temperature Properties of Plate during the Laminar Cooling Process Research and Improvement on the Rolling Force Model of Plate Analysis of Transverse Wall Thickness Precision of Steel Tube Rolled by Semi-Floating Mandrel Mill Generation Mechanism of Micro/Nano Machined Surfaces Based on Molecular Dynamics A Model of Cutting Forces for Ball End Mill in High Speed Machining Simulation and Experimental Investigation of Stiffness of the High Acceleration Linear Feed Drives Numerical Simulation of ANSYS-LS/DYNA Induced by Double-Edge Ball Tooth Hob Cutter Research on Interpolation Algorithm of Three-Links Hybrid Machine Tool Transmission Ratio Analysis and Controllable Tooth Profile Modeling for the Nutation Drive with Double Circular-Arc External and Internal Spiral Bevel Gears A Method for Performance Evaluation of Transfer Line with Unreliable Machines and Finite Transfer-Delay Buffers Closed-Loop Identification and Composed Controller Design for Precise Machining The Process Planning Simulation of Multi-Axis Numerical Control Based on Virtual Reality Redesign of a Complicated Component of Auto Body Based on the Properties of TWBs Application of Finite Difference Method in Billet Gradient Cooling Employed in Isothermal Extrusion The Strength Design and Check of Turbine Generator Based on FEA and Fatigue Evaluation Operation Mode for Personnel Integration in Manufacturing System Based on Product Life Cycle Multi-Field Co-Simulation Research on Suspension System of Forging Manipulator Based on Virtual Prototype Technology Coupled Simulation of Plastic Part and Mold Temperatures in the Filling Process of Rapid Heat Cycle Injection Molding FE Analysis of the Effects of Cutting Speed on Thermomechanical Responses of AISI 4142 Steel in High Speed Cutting A Mathematical Model for Predicting Residual Stresses in Pre-Stretched Aluminum Alloy Plate Exact Optimization of Time, Cost and Quality in Manufacturing Research on the Connecting Performances of 1/10 Taper Spindle / Tool-Holder for High-Speed NC Machine Using Efficiency Function in Analyzing the Ability of Flatness Control for a Cold Mill Modeling of Mircrostructure Evolution in Directional Solidification of Ni-Based Superalloy Turbine Blade Thermal Error Robust Modeling and Real Time Compensation Based on the GA-BPN Theory on a Vertical Machine Centre Stability Margin Sensitivity Analysis of a Multi-Rotor System Geared by Spiral Bevel Gear Pairs Structural Optimization of Non-Contact Vortex Negative Pressure Carrier A Hybrid Approach of ANN and HMM for Cutting Chatter Monitoring State Monitoring for Centrifugal Pump of PWR Based on HMM and SVM The Influence of Interfacial Thermal Contact Conductance on Resistance Spot Weld Nugget Formation A Particle Swarm Algorithm for Assembly Sequence Planning A Study of the Microstructure and Grain Size at the Welding Heat Affected Zone of an Industrial Pure Aluminum Investigation of Fixture Design Exploring Pre-Tensioning Forces CHAPTER 17: Computer-Aided Design, Manufacturing and Engineering A New Miniaturized CNC Machine Tool A 3D Nonlinear Finite Element Study on Biomechanical Behavior of Dental Implants Performance Assessment on Base-Isolated Smart Material-Structure System by Using Magnetorheological Fluids The Effect of Bending Rigidity on Measuring the Adhesion Work of Membrane The Novel Compound Evolutionary Optimization Algorithm with Hybrid Discrete Variables and its Application to Mechanical Optimization Design Optimization for Cold Forging by an Integrated Methodology of CAD/FEM/ANN Research on the Simulation Method for I.C.E Structural Acoustic Radiation Deformation of Seat Support during Free-Cooling after Ejection An Optimization Analysis of Prestressed Space Grid Structures Based on System Reliability Knowledge-Based Computer Aided Process Innovation Method Strength Analysis of Planetary Trains' Carrier of EPB Shield Machine Study on Boosting Curve for Electric Power Steering System Based on ADAMS Combining AST and Lock Techniques to Maintain Consistency of Multiple Objects in Replicated CAD Environments Study on Injection Mold Rapid Design System Based on Parametric Technology Finite Element Static and Dynamic Analysis for a Piston 4Ps Framework of Tooling Development and Management Experiment Study and Finite Element Analysis of the Failure for 75000 m3 Wet Gasholder KBCADFW: A Knowledge-Based Collaborative Computer-Aided Design Framework A Multi Autonomic Objects Flexible Workflow and its Knowledge Acquisition Supporting Engineering Design Process Thermodynamic Performance Simulation of Diesel EGR Cooler with Finned Tube Design of a Horizontal Moving Mechanism for High-Speed & High-Acceleration Stackers Hybrid Optimization Approach for Gas-Assisted Injection Molding Based on Metamodeling and Particle Swarm Algorithm Research on Numerical Investigation and Test Verification of Brake Performance in a Hydrodynamic Tractor-Retarder Assembly Mechanics Design of Connecting Frame in Aircraft Composite Cabin Three-Dimensional Thermal Analysis of Spherical Plain Bearings with Self-Lubricating Fabric Liner Partial Matching Algorithm of 3D CAD Models Based on the Constraints of Transition Features Virtual Prototype Simulation of Vertical Clamp Kinematics and Dynamics for Operating Safety A Multi-Agent Based Tool Path Planning Method for STEP-NC Compliant Milling Virtual Prototyping and Validation of an Automatic Washing Machine Modal Analysis of Flexible Assembling Fixture for Aircraft Panel Component Research on the Rapid Slicing Algorithm Based on STL Topology Construction Research and Realization of Digital Design System Wheel Loader Main Reducer Effects of Interference Fit and Preload on the Performance of Low-Speed Angular Contact Ball Bearing The Coding System for Automatic Injection Mold Integrated CAD/CAPP Research on Collision Method for Irregular Mechanism Kinematics Simulation A New Type Adjustable Shock Absorber and its Characteristic Model Toolpath Algorithm for Complex Pocket on the Network Optimization Accuracy Synthesis of a 3-PRS Parallel Manipulator Based on Genetic Algorithms A Kind of CAD/CAE Integrated Modeling Technology Based on FEATURE Research on Structure Rationalization Method of Product Family and its Application Application of Kinematics Simulation Technology in Agricultural Machinery Design Complicated Model Establishment and Second Development for Enterprises by MoldWizard A 3D Modeling System for Construction Work Simulation Based on Rendering and Dynamic Engines Parameterized Finite Element Analysis for Quick-Opening Supercritical Fluid Extraction Kettle Performance Prediction and Design Method for Centrifugal Pump Based on Computational Fluid Dynamics Extraction of Tiny Crack for Magnetic Ring Based on Wavelet Transform and Morphology Design and Analysis of MEMS-Based Actuator Research on Virtual Design and Simulation System for Manipulators of Multi-Degree of Freedom Research on Comfort Evaluation Method of Tool Handles Particle Swarm Optimization with Adaptive Inertia Weight and its Application in Optimization Design Dynamic Analysis of a Rotatable Mobile Robot Based on Turning Pose Matching Technology of Point Cloud Models Based on Combination Features Research on Parameters Optimization of Virtual NC Milling Based on Parallelism Selection Genetic Algorithm Dynamic Load Sharing Characteristic of Planetary Gear System with Load Balancing Mechanism Optimum Design of Roll Ring Optimal Layout of the Irregular Parts with Neural Networks Hybrid Algorithm Research on the Three-Dimensional Elliptical Motion of Rotary Traveling Wave Ultrasonic Motor Multi-Attribute Evaluation and Optimal Selection Using Information Axiom Distributed Monitoring System of Multi-Machine Tools Based on Wireless Sensor Network Topology Design Optimization of Rib Layout in Box Structure Deformation of Flexspline under Transmission Force in Harmonic Drive Design of Precise and Efficient Synchronized Multi-Axis Control Servo System Numerical Study of Dynamic Response of Steel Deck Pavement under Traveling Random Vehicle Load Investigation on the Contour Curve of Straighter Roll by Conjugate Revolving Quadric Theory Development of the Dressing Software for Form Grinding Wheel Used for Grinding Involute Helical Gears Structure Design and Multi-Domain Modeling for a Picking Banana Manipulator Research and Analysis on the Mechanical Characteristics of Brush Shape Cleaning Element in Spiral Installation STEP-Compliant Knowledgebase in Support of Customized Product Development for SMEs Numerical Simulation of the Cooling Effect by Air Conditioner and Spraying in High-Temperature Working Face Key Technology Research on Mould Heating System of Injecting Machine The Effects of Normal Gap Distribution on Cathode Design of Aero-Engine Blades in Electrochemical Machining Supplier Evaluation Based on Mobile Agent and Information Credibility Decomposition-Based Modularity Method for Product Collaborative Design Multi-Objective Optimization Design of Mold Platens on Large Precision Injection Molding Machines The HSM Cutters Management System Based on B/S A Structural Topological Optimization Method Based on Varying Displacement Limits and Design Space Adjustments Report Management in Performance Simulation for Complex Mechanical Product Arrangement Optimization of Instruments Based on Genetic Algorithm Design and Analysis of Horizontal Transfer System for Dual-Mode Trailer Scatter Point Cloud Denoising Based on Self-Adaptive Optimal Neighborhood Experimental Modal Analysis of CNC High Precision Surface Grinder with Horizontal Spindle and Rotary Table MGK7350 Effective Treatment of the Simulation Analysis under some Complicated Conditions Structural Dynamic Topology Optimization and Sensitivity Analysis Based on RKPM Application of an Improved Shell Element in Springback Analysis Development of CAD/CAM Software System for Large Non-Regular Steel Constructions Fire Protection Design for Steel Staggered-Truss Framing System Based on Mechanical Performance Calculation A New Computer Aided Design System of Belt Conveyor Dynamic Characteristic Analysis of the Horizontal Machine Center Study on Rapid Variable-Type Design Method of Gantry Crane Based on Templates Modeling and Control Method for Multi-Layer Distributed Flow Based on WFCP-Net Vision-Based Two-Handed Interaction for Augmented Reality Numerical Simulation on the Airflow of Electric Cutting Tool Pattern Recognition for Control Charts Using AR Spectrum and Fuzzy ARTMAP Neural Network Research on Multi-Process Route Decision-Making of Warm Forming for Projectile Bodies Multidisciplinary Collaborative Product Modeling in Distributed Network Environment A Novel Discovery Technique on Attribute Weight of Engine CBR Design System A Design of Large-Scale Speed Modulation in Hydraulic Cylinder and its Application Applying Fuzzy Neural Networks and Gray Theory to Construct a Modular Product Customization System Design and Finite Element Analysis of Corrugated Plate Boarding Bridge The Study of Mechanical Product Concept Design Method Based on Reverse Engineering Effect Study on Deformation of Links to Error of Parallel Manipulator Structural Analysis of Composite Shield Cutter-Head and Cutters Arrangement Optimization Based on Finite Element Factors Effect on Vortex Torque of Aerostatic Bearings The Effects of Different Defects on Buckling Behavior of Single-Walled Carbon Nanotubes The Study on Advancing Velocity of Hydraulic Support Collaborative Commodity Design System Based on DARFAD Research on Machining Face Gears Using a CNC Hobbing Machine A New Architecture of LCD Driver of Rail-to-Rail Buffer with High Gain Wide Range Phase-Field Simulation of Three-Dimensional Dendritic Growth Evaluation and Analysis of the Onlay Patellar Component in Total Knee Arthroplasty A Coupled Finite Element and Meshless Local Petrov-Galerkin Method for Large Deformation Problems Visual Computation of Thermohydrodynamic Lubrication of Dynamically Loaded Journal Bearings Computer-Aided Form Generation for Product Design Numerical Simulation of Flow Field of Metro Train Head Reconstruction of Human Skeleton Model Using Reverse Engineering Technology CHAPTER 18: Laser Based Manufacturing Research on Characteristic Microstructure and Properties of Fe20Ni3Mn Alloy Induced by Laser Shock Processing Formation of Periodical Sub-Micron Sized Structures on Silicon by Interfered Nanosecond Laser Pulses Picosecond Pulsed Laser Induced Melting of Monocrystalline Copper: A Hybrid Simulation Influence of Laser Parameters on Precision in Hybrid Plasma Laser Deposition Manufacturing Numerical Simulation on 3D Residual Stress Field of Both-Side Laser Shot Peened Specimen with Center-Hole A Powder Shrinkage Model for Describing Real Layer Thickness during Selective Laser Melting Process Effect of Scanning Velocity on Surface Hardening for Ti Substrate by CO2 Laser Study on the Factors Influencing the Layer Precision in Hybrid Plasma-Laser Deposition Manufacturing The Investigation of Partial Penetration Lap Laser Welding Applied on Stainless Steel Railway Vehicles Optical Properties Characterization of Thermoplastics Used in Laser Transmission Welding: Scattering and Absorbance Spectrum Changes of Partially Coherent Polychromatic Beams in Laser Resonators Research on Cladding Nickel on Copper Crystallizer Using Laser Metal Deposition Technique Analysis of 7050 Aluminum Alloy Crack Growth by Laser Shock Processing Simulative and Experimental Study on Laser Compound Forming of Plate Laser Cladding of an In Situ Synthesized TiB and TiC Reinforced Titanium Matrix Composite Coating on Ti6Al4V Orthotropic Experiment Research on Bending Angel of Laser Shock Forming Higher Precision Forming by Laser Peening under Pre-Bending Die Study on Chemical Mechanism of Laser and Fluid Corrosion Combining Processing Analysis on Microstructure of Laser Brazing Diamond Grits with a Ni-Based Filler Alloy Pitting Corrosion Behavior in Laser Weld Metals of 2205 DSS with Continuous Heat Treatment CHAPTER 19: Joining Processes Interfacial Microstructure and Phase Constitution of the Cu/Al Dissimilar Metals Joint Made by Contact Reactive Brazing Linear Friction and Electron Beam Welded Joints of Ti2AlNb/TC11 Optimizing the RSW Process Quality of Auto-Body via the Taguchi Method and a Neural-Genetic Approach Embedment of HA into Superplastic Ti-6Al-4V: Effects of Implantation Temperature Mechanical Properties of Single-Walled Carbon Nanotubes under Large Axial Deformation Study on Joint Residual Stress Induced by Laser Beam Welding of High Strength Automobile Thin Sheet Bond Thickness Effects upon Dynamic Behaviour in Adhesive Joints Parametric Analysis Mechanical Properties of Bolted Joints Microscopic Study on the Mechanism of Ultrasonic Nanowelding Mechanical Behaviors of Self-Piercing Riveting Joining Dissimilar Sheets Study on the Microstructure of Micro Laser Welded Joint of TiNi Shape Memory Alloy Sheet Double Metal Trimming Die Manufactured by Using Hardfacing Method Theoretical Study on Stress State in Adhesive Layer of Single Lap Joint under Eccentric Tensile Load The Arc Sound Characteristic on MIG Weld Penetration Study on Fuzzy Controller of Welding Arc Length Microstructures and Mechanical Properties on Laser Welded Joints of Automotive High Strength Complex Phase Steel Numerical Simulation for the Thermal Fatigue of Flip Chip Solder Joints Research on Laser Full-Penetration Welding In Situ TiB2 Particulate Reinforced ZL101 Composites Characteristics of Underwater Swirling Plasma Arc Cut Quality Weld Pool Shape Variations and Electrode Protection in Double Shielded TIG Welding CHAPTER 20: Rapid Manufacturing Technologies Investigation of UV Light Intensity Distribution of Integral Micro-Stereolithography System Research on Solidification Characteristics of Resin in High-Resolution Stereolithography System Effect of Corrosion Pillowing on Mechanical Properties of Lap Joint Development of a Novel Laser-Sintering Machine for Fabrication of Artificial Bone Development of High Speed Scanning System for the Fabrication of 3D Metal Parts Using Electron Beam Selective Melting Technology Prediction and Research of Single Point Incremental Forming Limit Design and Theoretical Analysis of Mini-Plunger Sprayer Used in SW2502 Fused Deposition Modeling System Rapid Fabrication of Micro-Gear via Vacuum Casting Technique of Silicone Rubber Mould Study on Fiber Laser Single Melting Track During Selective Laser Forming Microstructure and Performance Characteristics of Parts Produced via GMAW Surfacing Rapid Forming Experimental Research of Process Parameters in Metal Droplet Deposition Manufacturing Shaping Movement Analysis and Simulation of Ballscrew Manufactured by Cold Rolling Research on Patternless Casting CNC Manufacturing Technology and Development of the Equipment Process Research on the Laser Rapid Manufacturing Technology Research and Application on Reverse Design of Complicated Petroleum Aiguille Dual-Phase Materials Extrusion Process for Rapid Fabrication of Ceramic Dental Crown CHAPTER 21: Nontraditional Manufacturing Modeling and Analysis of NC Compliant Abrade Polishing for Surface of Revolution CAD/CAE System for Shaping Process of Three Dimensional Complicated Surfaces in Electrochemical Machining Fuzzy Optimization Design on Stranded Wire Helical Spring of High-Frequency Vibration Sieve Grinding Finishing Merging Electropolishing on Hole-Wall Surfaces Study on Optimization of Cathode's Feeding Route in Flexible Feeding Electrochemical Machining Evaluation of WEDM Surface Quality The Research of Digital Soft Switching Arc-Welding Inverter Electrochemical Machining of the Turbulated Hole Influences of Polishing Tool's Shape on Surface Roughness in Magneto-Rheological Finishing Fast Polishing of Single Crystal Diamond Optimum Geometrical Arrangement of Workpiece in the Ultrasonic Vibration Shoe Centerless Grinding Surface Roughness Characteristics of Fine ELID Cross Grinding for Silicon Wafers Chip-Ejection Mechanism and Experimental Study of Water Dispersant Dielectric Fluid on Small-Hole EDM Finishing Clearance Research on Magnetic Abrasive Finishing Research of Uniformity and Effect on Crankshaft Barrel Finishing Finishing Effect and Uniformity on Gas-Particle Two-Phase Swirling Flows Finishing for Hole Surface Simulation and Experiment Research on the Swirling Airflow Compounded with Magnetic-Field Finishing Study on Bio-Limited Forming Technology Based on Micro-Composite Sol-Gel Coating Study on the Conditions of Near-Field Acoustic Levitation The Function of Magnetic Field in a Magnetic-Electrochemical Compound Polishing Effects of Polymer Particles Suspending in Dielectric Fluid on Surface Roughness of EDM Simulation of Particles Movement in Powder Mixed EDM Structural Analysis and Building an EDM Process Model Temperature Field Model in Plasma Arc Forming of Laminated Clad Metal Sheets Containing Defects Heat Absorbing Rate in Laser Drilling of YG8 Alloy Gas-Liquid Combined Multiple Cut in High-Speed WEDM Research on Hydroforming of Bimetallic Lined Pipe Novel Jump Control for Debris Processes of Electrical Discharge Machining with Direct-Drive Spindle CHAPTER 22: Nanofabrication, Nanometrology and Applications Influence of Substrates and Annealing on the Al-Cu-Fe Nano Films Electrical Characteristics of Extended Gate FET Sensing Chip Constructed for Detection of DNA Analytical Model of Unconstrained Nonlocal Higher-Order Nano-Plates for Bending Analysis In Situ Nanoscale Deformation Studies on Micro Copper Wires Using Atomic Force Microscopy A Multiscale Modeling Approach for Carbon Nanotubes Error Compensation in One-Point Inclined-Axis Nanogrinding Mode for Small Aspheric Mould Synthesis and Photoluminescence Properties of Novel SnO2 Zigzag Nanoribbons One-Point Nano-Grinding for Micro-Aspherical Glass Lens Mould Design and Research on a Novel NEMS Accelerated Sensor Based on GaAs PHEMT Fabrication and Structure Measurement of the Double-Barrier Nano Film Resonant Tunneling Gyroscope An Improved Thermal Type Microsensor with Thermal Isolation Microcracks CHAPTER 23: Metrology and Measurement An Improved Calibration Method for Optical 3D Measuring System Using Cross Target Based on Bundle Adjustment Algorithm Application of Pressure Test System in Dispenser for Gasoline New Method for Large-Scale Dimensional Metrology Using Laser Tracker System Study on the Technologies of Rapid Three-Dimension Optical Measurement for Welding Deformation of Sheet Materials Research on Mechanical Fault Identification Based on Improved SVM Fabrication of Piezoelectric Thickness-Shear-Mode Acoustic Wave Sensing Device and its Application Evaluation of Measurement Uncertainty for High Precision Gear Involute Profile Measuring System Influence of Specimen Sampling on Internal Residual Stress Test Research on High-Precision Measurement Platform for Optical Aspheric Surface and Corresponding Error Compensation Study on On-Machine Inspection Technology of Machining Center Based Exploration on Applying Non-Contact Photoelectric Detection Method for Double-Enveloping Hourglass Worm On Determination of Geometric Damage Tensor Hybrid Numerical-Optical Methods for Analysis of Mechanical Structures In Service Detection of 45 Steel's Rotary Bending Fatigue Damage Based on Metal Magnetic Memory Technique Tower Type Sensors for Monitoring Corrosion Risk in Cover-Zone Concrete Intelligent Moisture Controlling System for Molding Sand The Technique of Online Measurement and Data Processing for Aspheric Machining Calibration and Registration for Inspection Robot with Contact Probe Device and Method for Large Size Aspheric Measurement Experimental Modal Analysis of Roller Gap Sensor Structure on Hot Rolling Mill Development of Novel High Precision Angular Displacement Sensor Post-Weld Quality Inspection for CO2 Laser Tailored Blank Welding with Vision Sensor The compact Platform for In Situ Nanoindentation and Scratch Test Visual Integrated Measurement on Geometry Parameters of Circular Saw Blade Research on Measuring Path and Surface Fitting Algorithm for Non-Axisymmetric Aspheric Research on Quality Evaluation System of Dynamic Alliance Based on Life-Cycle Study of Simulation Tester for Key Rubbing Pairs in Internal-Combustion Engine Detection of Unbonds in Honeycomb Sandwich Structure Using Lock-In Thermography The Design of VI-Based Synthesized Testing System for Belt Conveyors Fast Location of Thermal Target with Low Offset and Spatial Filter of Winner-Take-All Circuit Characteristics Identification of Overlapping Vibration Signals on Mallat Study on the Disturbance of Rotor-Bearing System Caused by Circumferential Loading Torque Study on the Measuring System of the Planar Parallel Micro-Motion Worktable's Location and Orientation Surface Roughness Pattern Measurement of Tensile Specimen by Using Digital Holography CHAPTER 24: Other Related Topics The Finite Element Analysis of the End Anchorage under Larger Prestressing Load in Rehabilitation Engineering Research on Decision-Making Model for Mechanical Motion Scheme The Study on Optimal Matching of Power System of Hybrid Hydraulic TLT Study on Edge Detection Technique in Material Bag Image The Design of New Type Muffler Used For Steam Turbine's Exhaust Device Reliability Analysis of Prestressed Steel Structure in Regards to Temperature Action The Design of Mechanical System for Harbor Basin Wave Maker Product Development Oriented Knowledge Management Exploiting Critical Path Method for Evaluation of Conceptual Design Efficiency- Reinforcement Technology Study for Hydraulic Reciprocating Sealing Based on TRIZ S-Field Analysis The Principle Studies of Series Multistage Axial Ram Pumps and the Fluctuation Analyses Structure Buckling Non-Probabilistic Reliability Index Calculation of Ventilated Supercavitating Vehicles The Analysis of Failure Induced by Manufacturing Defect in Cu-30Ni Alloy Condenser Tube to Improve the Finished Product Detection of Small Damage of Beam Structures Based on the Slope of Proper Orthogonal Mode Fuzzy Pattern Recognition of Steelmaking Process for Converter Study on Impinging Streams Reactor for Sewage Purification Analysis on Cutting Ability of Picks on Continuous Miner New Type of Cantilever Crane for High-Speed Railway Track Plate Constructions Study on a Capacitive Micro-Mechanic Gyroscope Development of the Self-Adaptive Pipeline Cleaning Robot Self-Adaptive Suppression of the Euler Beam Remnant Vibration Using the Interior Inlay Viscous Fluid Unit Method Research on Tempering Process of LZ20Mn2 Seamless Pipe for Axle Study of a Novel Approach of Active On-Line Balancing Device for High-Speed Spindle System Research on Fatigue Damage of Ferromagnetic Material by Metal Magnetic Memory Methods Analysis of the Hydrodynamic Effect in Laser-Textured Mechanical Seal Faces The Realization of Monitoring System for Stacking Crane Using Plotting Finite State Machine Simulation and Experiment for Rigid and Flexible Wings of Flapping-Wings Microrobots A Passivity-Based Approach to the Rotor Resistance Estimation and Sliding Mode Control for Induction Motors Tri-Objective Optimization in Production Based on Stochastic Principle Effect of Grinding Wheel Diameter Change on Geometrical Parameters of Ball-Nose End Mill Dynamic Analysis on Noise and Vibration Study of Flexible Wiper Blade System

「Nielsen BookData」 より

詳細情報

• NII書誌ID(NCID): BB02223073
• ISBN:
  • 9780878492800
• 出版国コード: sz
• タイトル言語コード: eng
• 本文言語コード: eng
• 出版地: Stafa-Zurich
• ページ数/冊数: 5 v.
• 大きさ: 25 cm
• 親書誌ID:
  • BA24926058