Lecture notes on composite materials : current topics and achievements
著者
書誌事項
Lecture notes on composite materials : current topics and achievements
(Solid mechanics and its applications, v. 154)
Springer, c2008
- : hbk
- : ebook
大学図書館所蔵 全2件
  青森
  岩手
  宮城
  秋田
  山形
  福島
  茨城
  栃木
  群馬
  埼玉
  千葉
  東京
  神奈川
  新潟
  富山
  石川
  福井
  山梨
  長野
  岐阜
  静岡
  愛知
  三重
  滋賀
  京都
  大阪
  兵庫
  奈良
  和歌山
  鳥取
  島根
  岡山
  広島
  山口
  徳島
  香川
  愛媛
  高知
  福岡
  佐賀
  長崎
  熊本
  大分
  宮崎
  鹿児島
  沖縄
  韓国
  中国
  タイ
  イギリス
  ドイツ
  スイス
  フランス
  ベルギー
  オランダ
  スウェーデン
  ノルウェー
  アメリカ
注記
Includes bibliographical references
内容説明・目次
内容説明
Composite materials are heterogeneous by nature, and are intended to be, since only the combination of different constituent materials can give them the desired combination of low weight, stiffness and strength. At present, the knowledge has advanced to a level that materials can be tailored to exhibit certain, required properties. At the same time, the fact that these materials are composed of various, sometimes very different constituents, make their mechanical behaviour complex. This observation holds with respect to the deformation behaviour, but especially with respect to the failure behaviour, where complicated and unconventional failure modes have been observed. It is a challenge to develop predictive methods that can capture this complex mechanical behaviour, either using analytical tools, or using numerical me- ods, the ?nite element method being the most widespread among the latter. In this respect, developments have gone fast over the past decade. Indeed, we have seen a paradigm shift in computational approaches to (composite) ma- rial behaviour. Where only a decade ago it was still customary to carry out analyses of deformation and failure at a macroscopic level of observation only - one may call this a phenomenological approach - nowadays this approach is being progressively replaced by multiscale methods. In such methods it is r- ognized a priori that the overall behaviour is highly dependent on local details and ?aws.
目次
Holm Altenbach Analysis of Homogeneous and Non-homogeneous Plates 1 Classification of Structural Models 1.1 Introductional Remarks 1.2 Two-dimensional Structures-Definition, Applications, Some Basic References 1.3 Formulation Principles, Historical Remarks 2 Classical Plate Theories 2.1 Small Deflections 2.2 Large Deflections 2.3 Kirchhoff Plate 2.4 Mindlin Plate 2.5 Von Karman Plate 3 Laminates and Sandwiches 4 Direct Approach Based Plate Theory 4.1 Motivation 4.2 Direct Approach for Plates and Shells 4.3 Tensors and Their Symmetry Groups 5 Final Remarks References Rene de Borst Numerical methods for the modelling of debonding in composites 1 Introduction 2 Levels of observation 3 Three-dimensional framework 4 Zero-thickness interface elements 5 Solid-like shell formulation 6 Meshfree methods 7 The partition-of-unity concept 8 Delamination in a solid-like shell element 9 Discontinuous Galerkin methods References Ryszard Pyrz Micromechanics of Composites -Overall Elastic Properties 1 Introduction 2 Representative Volume Element 3 The Eshelby Equivalent Inclusion Method 3.1 Average strain and stress theorems 3.2 Relation between averages 3.3 The Eshelby solution 3.4 Equivalent inclusion method 4 The Mori-Tanaka Theory References Tomasz Sadowski Non-symmetric thermal shock in ceramic matrix composite (CMC) materials 1. Introduction to ceramic and metal matrix composites 2. Thermomechanical properties of CMC's and MMC's 2.1 Two-phase CMC with different elastic components 2.2 Two-phase CMC's with plastic inclusions and MMC's with elastic inclusions 2.2.1Thermomechanical properties 2.2.2 Modelling of the whole stress-strain curve fro MMC 2.2.3 Constitutive equations for FGM's in 3-D formulation by self-consistent approach 2.2.3 Constitutive equations for FGM's in 3-D formulation by self-consistent approach 3. Temperature field under transient thermal loading 3.1 FEA approach for heat transfer equation (26) 3.2 FD approach for heat transfer equation (26) 4. Transient thermal stress state 5. Thermal residual stress due to technological cooling process 5.1 Analytical models 5.2 Numerical models 6. Basic fracture mechanics concepts in functionally graded materials (FGM) 6.1 Rule of mixture to estimate the fracture toughness in FGMs 6.2 Crack-bridging approach to assess the fracture toughness 7. Non-symmetric thermal shock in monolithic ceramic and FGM strip 7.1 Transient temperature distribution during thermal shock 7.2 Thermal and residual stresses 7.3 Thermal stress intensity factor 7.4 Numerical example 8. Two-dimensional thermal shock problem in layered circular plates 8.1 Samples preparation and experimental procedure 8.2 Theoretical formulation 8.2.1 Thermal and mechanical properties of monolithic and FGM material 8.2.2 Heat conduction problem in FGM circular plate specimens 8.2.3 Determination of the thermal stress 8.3 Numerical example 9. Concluding remarks 10. References Rene de Borst J. Rethore M.-A. Abellan A precis of two-scale approaches for fracture in porous media 1. Introduction 2. Balance equations 3. Constitutive equations 4. Weak form of the balance equations 5. Micro-macro coupling 6. Discontinuities in a two-phase medium 7. Examples: stationary and propagating cracks 8. Concluding
「Nielsen BookData」 より