Advances in experimental mechanics VII : selected, peer reviewed papers from 7th International Conference on Advances in Experimental Mechanics, 7th-9th September 2010, School of Engineering, University of Liverpool, UK
著者
書誌事項
Advances in experimental mechanics VII : selected, peer reviewed papers from 7th International Conference on Advances in Experimental Mechanics, 7th-9th September 2010, School of Engineering, University of Liverpool, UK
（Applied mechanics and materials, v. 24-25）
Trans Tech Publications, c2010
大学図書館所蔵 全1件
注記
Includes bibliographic references and index
内容説明・目次
内容説明
The 2010 Annual British Society for Strain Measurement Conference is the seventh in the series on Advances in Experimental Mechanics, and the fifth time that the papers have been presented as a volume in the Applied Mechanics and Materials series.
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 61 papers making up this volume reflect strikingly the diverse nature of experimental mechanics. The fourteen sessions address various disciplines: e.g. aerospace, mechanical and civil engineering and state-of-the-art technologies such as biomechanics, novel sensors, and composite and cellular materials. The papers were contributed by workers in both academia and industry; with half of the contributions coming from outside of the UK: thus reflecting the international flavour of this event. This volume will be essential reading for all of those interested in the subject.
目次
Committee
Sponsors
Preface
Mechanical and Transport Properties of Concrete at High Temperatures
Keynote Lecture 2
Experimental Characterisation of Parameters Controlling the Compressive Failure of Pultruded Unidirectional Carbon Fibre Composites
BSSM Measurements Lecture
Aspects of Uncertainty Analysis for Large Nonlinear Computational Models
Session 1: Structural Health Monitoring
Detection of Cracking in Gear Teeth Using Acoustic Emission
Active Sensor Arrays for Damage Detection
Towards a Hybrid Infrared Approach for Damage Assessment
Session 2: Vibration
Designing a Hollow Langevin Transducer for Ultrasonic Coring
Experimental Modal Analysis of an Automotive Powertrain
Investigation into the Damping and Stiffness Characteristics of an Elevator Car System
Analysis of Sensors for Vibration and Nip Forces Monitoring of Rubber Coated Rollers
Session 3A: Composite and Cellular Materials 1
Evaluation of Edge Cracks in Cross-Ply Laminates Using Image Correlation and Thermoelastic Stress Analysis
Mechanical Behavior of Syntactic Foams for Deep Sea Thermally Insulated Pipeline
Analysis of the Strain and Stress Fields of Cardboard Box during Compression by 3D Digital Image Correlation
Correlation between Full-Field Measurements and Numerical Simulation Results for Multiple Delamination Composite Specimens in Bending
Towards a Planar Cruciform Specimen for Biaxial Characterisation of Polymer Matrix Composites
Session 3B: Novel Sensor Technology
Measurement of Mechanical Strain Using Chromatic Monitoring of Photoelasticity
Development of a Methodology to Assess Mechanical Impulse Effects Resulting from Lightning Attachment to Lightweight Aircraft Structures
A Laser Speckle Method for Measuring Displacement Field. Application to Resistance Heating Tensile Test on Steel
Characterisation of Full-Field Deformation Behaviour Using Digital Imaging Techniques
Digital Holographic Interferometry by Using Long Wave Infrared Radiation (CO2 Laser)
Session 4: Civil Engineering
Size of the Fracture Process Zone in High-Strength Concrete at a Wide Range of Loading Rates
Practical In Situ Applications of DIC for Large Structures
From the Inside, Out Use of Optical Measuring Techniques for Wind Turbine Development
Details of Temperature Compensation for Strain Measurements on NPL Bridge - Demonstrator for SHM
Effect of Loading Rate on the Fracture Behaviour of High-Strength Concrete
Session 5A: Non Linear Behaviour
Numerical Prediction of the Response of Metal-to-Metal Adhesive Joints with Ductile Adhesives
Experimental Characterization of the Viscoplastic Material Behaviour of Thermosets and Thermoplastics
Strain Evolution Measurement at the Microscale of a Dual Phase Steel Using Digital Image Correlation
Biaxial Ratcheting Response of SS 316 Steel
On the Mutual Interactions of Monotonic and Cyclic Loading and their Effect on the Strength of Aluminium Alloys
Session 5B: Fracture and Damage
Validation of Acoustic Emission (AE) Crack Detection in Aerospace Grade Steel Using Digital Image Correlation
Towards the Derivation of Stress Intensity Factors by Parametric Modelling of Full-Field Thermoelastic Data
A SEM-Based Study of Structural Impact Damage
Application of Real-Time Photoelastic Analysis to Single Fibre Fragmentation Tests
Characterization of Fiber Bridging in Mode II Fracture Growth of Laminated Composite Materials
Session 6A: Residual Stresses
Evaluation of the Impact of Residual Stresses in Crack Initiation with the Application of the Crack Compliance Method Part I, Numerical Analysis
Evaluation of the Impact of Residual Stresses in Crack Initiation with the Application of the Crack Compliance Method Part II, Experimental Analysis
Mapping Residual Stress Profiles at the Micron Scale Using FIB Micro-Hole Drilling
Session 6B: Biomechanics
Acetabular Component Deformation under Rim Loading Using Digital Image Correlation and Finite Element Methods
Skin Thermal Effect by FE Simulation and Experiment of Laser Ultrasonics
Biomechanics and Numerical Evaluation of Cervical Porcine Models Considering Compressive Loads Using 2-D Classic Computer Tomography CT, 3-D Scanner and 3 -D Computed Tomography
Session 7: Manufacturing Processes
Spot Weld Strength Determination Using the Wedge Test: In Situ Observations and Coupled Simulations
Improving Fatigue Performance of Alumino-Thermic Rail Welds
The Effect of Ultrasonic Excitation in Metal Forming Tests
Modeling of Coating Stress of Plasma-Sprayed Thermal Barrier Coatings
Session 8A: Impact and Dynamics
Tensile Properties of Die-Cast Magnesium Alloy AZ91D at High Strain Rates in the Range between 300 s-1 and 1500 s-1
The Dynamic Buckling of Stiffened Panels -A Study Using High Speed Digital Image Correlation
Finite Element Model Updating of a Thin Wall Enclosure under Impact Excitation
What we Can Learn about Stick-Slip Dynamics
Determination of High Strain-Rate Compressive Stress-Strain Loops of Selected Polymers
Session 8B: Identification
Identification of the Shape of Curvilinear Beams and Fibers
Construction of Shape Features for the Representation of Full-Field Displacement/Strain Data
An Innovative Own-Weight Cantilever Method for Measuring Young's Modulus in Flexible Thin Materials Based on Large Deflections
Identification of the Mechanical Properties of Superconducting Windings Using the Virtual Fields Method
Measuring the Static Modulus of Nuclear Graphite from Four-Point Flexural Strength Tests and DIC
Session 9: Composite and Cellular Materials 2
Experimental and Numerical Buckling Analysis of Delaminated Hybrid Composite Beam Structures
Effects of Bonded Splice Joints on the Flexural Response of Pultruded Fibre Reinforced Polymer Beams
Assessment of Quasi-Static and Fatigue Loaded Notched GRP Laminates Using Digital Image Correlation
Comparison of the Drop Weight Impact Performance of Sandwich Panels with Aluminium Honeycomb and Titanium Alloy Micro Lattice Cores
Viscoelastic Characterization of Short Fibres Reinforced Thermoplastic in Tension and Shearing
Session 10: Education
The Role of Experimental Stress Analysis at Graduation and Post Graduation Courses - A Brazilian Case
「Nielsen BookData」 より