Advanced engineering materials : selected, peer reviewed papers from the International Conference on Manufacturing Science and Engineering (ICMSE 2011), April 9-11, 2011, Guilin, P.R. China

著者

• International Conference on Manufacturing Science and Engineering
• Zeng, Jianmin

書誌事項

Advanced engineering materials : selected, peer reviewed papers from the International Conference on Manufacturing Science and Engineering (ICMSE 2011), April 9-11, 2011, Guilin, P.R. China

edited by Jianmin Zeng ... [et al.]

（Advanced materials research, v. 194-196）

Trans Tech Publications, c2011

• : [set]
• Part 1
• Part 2
• Part 3

注記

Includes bibliographical references and indexes

内容説明・目次

内容説明

This special volume brings together the latest advances in, and applications of, iron and steel, micro/nano materials, metal alloy materials, composites, earthquake-resistant structures, materials and design, tooling testing and evaluation of materials, waste engineering and management, etc. It will not only provide readers with a broad overview of the latest advances, but also constitute a handbook for use by researchers in this field.

目次

Sponsors, Committees and Preface 1. Iron and Steel Simulation Research on the Penetration Phenomenon of Long Rod Armour-Piercing Projectile with Different Materials Adsorption Behavior of Sulfamethoxazole as Inhibitor for Mild Steel in 3%HCl Solution Precipitates and Luders Elongation in Ferritic Stainless Steels Stabilized with Ti and V The Analysis of Temperature Field and Residual Stress Distribution during H-Beam Cooling Process Research of a Novel Low-Carbon High-Manganese Alloy Containing Boron Effects of Mn on the Precipitation Behaviors in High-Nitrogen Austenitic Stainless Steels Fractal Analysis of Raceway Boundary in COREX Melter Gasifier Model Corrosion Inhibition of 45# Mild Steel in Acidic Solution by Some Norfloxacin Microstructures and Textures During Annealing in Low Carbon Al-Killed Steels with Low Finishing Temperatures and High Coiling Temperatures Numerical Simulation for Direct Reduction of Pure Zinc Oxide Pellet Containing Carbon A New Evaluation Index of Coke High Temperature Properties - Starting Reaction Temperature Effect of High Magnetic Field on Diffusion Behavior of Carbon in Pure Iron Synthesis Pathway of Dioxins in Iron Ore Sintering Process Effect of Magnetic Field Direction on Texture Evolution in Cold-Rolled IF Steel Sheet at the Initial Stage of Recrystallization Atomistic Model of Amorphous Silicon Nitride by Melt-Quench Method Study on the Recrystallization Behaviour of Hot Deformed Austenite in GCr15 Bearing Steel Microstructure and Properties of 65Mn Steel after Austenite Inverse Phase Transformation by Sub-Temperature Quenching A Study on Microstructure of Ductile Ni-Resist Cast Iron for Exhaust Manifolds and Mechanical Property at the Condition of Altermative Thermal Cycles Preparation of Fe-Cu-Ni-Mo-C Alloy with High Performance by Powder Metallurgy Warm Compaction Crack Research for Welded Joint of Steel Truss Bridge Synthesis and Dielectric Properties of Ba(Ti,Y)O3 Solid Solutions to Ba3Ti2YO8.5-BaTiO3 Composites Hypereutectic Al-Si-Mg In Situ Composite Prepared by Melt Superheating The Study of Low-Velocity Impact Characteristics and Residual Tensile Strength of Carbon Fiber Composite Lattice Core Sandwich Structures Simulation of Microstructure and Grain Size in Welding Heat Affected Zone Using Monte Carlo Method Microstructure and Mechanical Properties of Hot-Rolled Low-Carbon Medium-Manganese TRIP Steels Synergistic Inhibition Effect of Sodium Silicte and Phytic Acid for Carbon Steel in Neutral Salt Water Precipation and Dissolution Behaviours of Secondary Phase in J55 Steel During Continuous Casting, Conveying and Heating The Influence of Enamel Firing Process on Microstructure and Mechanical Properties of Steel Substrate Characteristics of Hot Ductility and Fracture in Micro-Alloyed Q345B Structural Steel Electrochemical and Quantum Chemical Investigations of Tinidazole as Corrosion Inhibitor for Mild Steel in 3% HCl Solution Effect of Quenching Temperature on Microstructures and Mechanical Properties of Boron-Nickel-Added Nb-Treated HSLA H-Beams Melting Temperature of a Selected Area in CaO-MgO-Al2O3-SiO2 Slag System Effects of Temperature and Strain Rate on Thermal Deformation-Behaviour of Cu-P Weathering Steel Experiment Research on Argon Shroud for the Protection of Steel Casting Study on Thermal Physical and Chemical Properties of Sodium Pyroxenite in Baiyunebo Iron Ore Effects of Impact Angles on Erosion-Abrasion Properties of Hypereutectic Al-Mn Alloy Matrix Composite Reinforced with Al2O3 Particulates Study on Heavy Section Forging Steel for Reactor Pressure Vessel Applying Simulation Methods Effects of Compound Silicate Gangue on Mineral Composition and Microstructure of Sinter Produced by Baiyunebo Iron Ore Concentrates Studies on Technological Parameters of Optimal Soft Reduction about Superwide Slab Caster Effect of Nitrogen on Mechanical Properties of 20MnSi at High Temperature Structure Evolution in Steel Wires During Drawing A Novel Characteristic Method on Fatigue Crack Growth of N80 Casing Drilling Steel Study on the Durable Factors of the Grain Size in 18CrNiMo7-6 by Heating and Cooling Method Aluminizing Mechanism and Corrosion Resistance of Pipeline Steel X80 by Combined Pack Cementation Process under Low Temperature Effects of Rare Earths on Structural Transformation of Heavy Rail Steel Development of Texture and Grain Boundary Character in a Boron Bearing IF Steel after Recrystallization Annealing Discussion on Burden Calculation of Ferromanganese Alloy Production Effect of Heat Imput on Microstructure and Toughness of High Strength Bridge Steel Study on Ultrasonic Test Defects Causes of Medium Plate Research on the Impact Toughness of Basalt Fiber Reinforced Composites Study on Characteristics of Ultrasonic Fields by Hydraulic Model of Ladle Refining Study on Effects of Pretreatment on Carbide of a Medium-Alloy High Carbon Steel The Comparison of Electrolysis Manganese Craft on Stainless Steel and Titanium The Influence of Basalt Fiber Orientation on the Mechanical Property of Composite Board Effect of Mold Flux for Casting on Microstructe of Mould Powder Study on the Cooling Process of Low Yield Ratio 590-780MPa Grade Steel Plates for High-Rise Buildings Effect of Divorced Eutectoid Transformation Temperature on Behaviour of Cementite Growth in GCr15 Steel Cold Model Study of Raceway in COREX Melter Gasifier Behaviours of Zinc and Lead in Blast Furnace of Baotou Iron and Steel Group Co. Tensile Strength Statistical Analysis of B610CF Steel Evolution of Microstructure and Oxidation Layer of 430 Stainless Steel During Hot Rolling Effect of Heat Treatment on the Structure and Mechanical Properties of the Hot-Rolling Plate of Fe-42% Ni (4J42) Study of the Coefficient of Thermal Expansion for Steel Q235 Study of Bake Hardenability for Hot Rolling Low Carbon Steel Effect of Ultrasonic Treatment Time on Inclusions in High Carbon Steel Effects of Applied Compressive Stress on Microstructure and Mechanical Properties of Cr-Mo Steel During Continuous Cooling Bainitic Transformation A Study on Flow Characteristics of Coherent Jet Oxygen Injector Investigation on Friction and Wear Property of Al2O3-Sio2(Sf) / AZ91D Composite Investigation on Aging Behaviour of Al2O3-Sio2(Sf) / AZ91D Composites A New Idea for Improving Heat Fade Performance of Organic Based Friction Materials Wear Behaviour of Thermal Spray Welded FeNi and CeO2 Composite Coatings Effect of Static Magnetic Field on Distribution of Elements in the Fe-S, Fe-Si, and Fe-Mn Alloys Effect of Pulsed Electric Field on the Distribution and Migration of P, S, and Si Elements of Fe-Based Alloys The Effect of Hot-Rolled Coiling Time on the Texture of a New Cold-Rolled Non-Oriented Electric Steel 2. Micro / Nano Materials Physicochemical, Gel Structure and Morphology Properties of Nano Rice Starch Prepared by Ultrasound Facile Preparation of Nanoporous SnO2 for Application in Photodegradation of Methylene Blue Preparation of PS@SiO2, PS@TiO2,PS@TiO2/SiO2 Core-Shell Composites by a Spray Drying Process and Their Hollow Spheres after Removing PS Cores by Calcinations Combined Manufacturing Process of Electrochemical-Etching and Electroplating on Nanoporous Silicon for its Metallization Synthesis of Gold Nano- and Microplates by Tryptophan and 5-Hydroxy-Tryptophan Influence of Temperature for Synthesis of Carbon Nanofibers from the V-Type Pyrolysis Flame Characterization of Protein Powder from Waste Rabbit Hair Corrosion Behaviour of AISI 304 Austenitic Stainless Steel Fabricated by Equal-Channel Angular Pressing Controllable Assembly of Au Nanorods through Recognition of h-IgG and Anti-h-lgG Fab Magnesium-Based Hydrogen-Storage Materials from Milling for Sulfocompound Hydrodesulfurization Fabrication of Ti2AlN by Mechanical Alloying and Hot Press Sintering Electrochemical Synthesis for Uniform and Large-Scale Zinc Oxide Nano Structure Films Study on the Spread of the Energy Gap in Nanostructure System Carbon Nanotubes with Uniform Wall Thickness Synthesized Via a Solid-Liquid Reaction Synthesis, Characterization and Gas Adsorption of Titania Nanotubes Preparation of Nano-Powders of ITO Research on Ultrafine PTFE Particles with Grease Tribological Properties Synthesis of Nanocrystalline TiC1-xNx by High Energy Milling Researching on the Adsorption of Protein on Gold Nanoparticles The Lattice Change of Ni-P Layer Coated on Single-Walled Carbon Nanotubes The Acoustic Insulation Property of a New Non-Woven Material Fabrication and Characterization of Nanocrystalline NiO Prepared by Sol-Gel Process Rapid Fabrication of Cu-Al2O3 Nanocomposition Coatings Preparation and Characterization of Cassava Starch-Chitosan/Montmorillonite Nanocomposites Absorption of Eriochrome Blue Black on Polyaniline/Attapulgite Nanocomposites Synthesis of Type-A Zeolite in Hydrothermal Condition with Stellerite Synthesis and Characterization of Titanate Nanotubes and Nanowires in a Revolving Autoclave Large-Scale Patterning and Assembly of Carbon Nanotubes by Microfluidic Hydrodynamic Focusing Engineering of Soybean Extract Powder: Identification, Characterisation and Stability Evaluation Preparation, Characterization of Nanoscale Zero-Valent Iron and its Application in Coking Wastewater Treatment Fabrication of the SnO2/Al2O3 Catalysts through Electrospinning Electromagnetic Characteristics and Microwave Absorption Properties of CNT Composite Influences of Nd3+ Ions Substitution on the Structure and Electromagnetic Properties of the Nanocrystalline Co0.5Zn0.5Fe2O4 Ferrite Ni-Al2O3 Nanocomposites Electroforming Process under Ultrasonic and Agitation Study the Relative Permeability of Ferrofluid with the Mean Value Analysis of Experimental Apparent Gravity Effect of Edge Activator on Characteristic and in Vitro Skin Permeation of Meloxicam Loaded in Elastic Liposomes Development of Chitosan Nanoparticles for Gene Delivery Using Electrohydrodynamic Spraying Techniques PbSe Nanocrystals Synthesized by an Ultrasonic Electrochemical Method A Hollow Microneedle Carrier for Enhancing Skin Penetration of Large Molecular Compounds Corrosion Behaviour of Ultra-Fine Grain Chromium Bronze Prepared by Equal-Channel Angular Pressing in Nacl Solution Preparation and Characterisation of TAM-PLGA Microspheres by Solvent Evaporation Synthesis of High Surface Area Porous Silicon Carbide by a Modified Sol-Gel Method Self-Supporting Honeycomb Films of Polyphenylene Oxide Fabrication and Characterization Investigation of Nano-Powders Made by Spark Discharging Reaction Sputtering Phenomena of ZnS Nanoparticles with Graphite Sheaths by Impacting of High-Energy Electron in a Transmission Electron Microscope Study on Design for Remanufacturing Facing Total Remanufacturing Process Preparation Principle and Crystal Growth Kinetics of Loaded Nanocrystal TiO2 Synthesis and Field Emission of ZnO Bundles with High Aspect Ratio by Solution Method Carbon Nanotube Templated Growth of the Nano-Crystalline NaY Zeolite Fabrication of Large-Area Silicon Nanowire Arrays Based on Electroless Metal Deposition Technological Properties of Poplar Particle/Waste Rubber Powder Composites Effect of Additive on Microstructure and Property of Bulk Nanocrystalline Co-Ni Alloys Prepared by JED Coagulation Method for Preparing Antimony-Doped Tin Oxide (ATO)/Poly(methyl Methacrylate) Nanocomposites and their Electrical Conductivity and Thermal Stability Preparation and Photoluminescence Properties of Tadpole-Like Amorphous Silica Nanowires Optical Studies on Multiwalled Carbon Nanotubes via Modified Wolff-Kishner Reduction Process Preparation of Coral-Like -Fe2O3 Nanostructures and Magnetic Properties Effects of Solution Parameters on Morphology and Diameter of Electrospun Polystyrene Nanofibers One-Step Wet Synthesis and Characterisation of Hydrophobic Magnesium Hydroxide Facile Fabrication of Single Crystalline Fe3O4 Nanorods and its Magnetic Properties Preparation of Composite Conductive Microspheres Used in Anisotropic Conductive Adhesive Films Fabrication and Characterization of Chitosan-Ethylenediaminetetraacetic Acid/Polyvinyl Alcohol Blend Electrospun Nanofibers Preparation of Nicob/SiO2 Nanoalloy Catalysts and their Catalytic Hydrogenation Performance Influence of Sintering Temperature on Densification and Microstructure of Zn3Nb2O8 Ceramics Derived from Nanopowders Rapid Preparation of V2O3 and VN Nanocrystals by Ammonolysis of the Precursor VOC2O4*H2O Appropriate Conditions for Preparation of Nanosized WO3 through High-Energy-Milling The Tribological Properties of PA6/UHMPE Blended Short Carbon Fiber Nanoclay Filled Nanocomposites Analysis the Structure Parameters of the SOI Rib Waveguide Spin Polarized Transport through Structures Consist of the Ferromagnetic Semiconductor in Presence of a Inhomogeneous Magnetic Field Surfactants-Controlled Morphosynthesis of Strontium Carbonate Preparation of ZnO Nano-Suspension and its Antibacterial Effect on Escherichia Coli Hydrothermal Preparation and Formation Mechanism of ZnSn(OH)6 Cubic Aggregates and Zn2SnO4 Octahedra Effects of Process Conditions on Properties of Nano-Magnetic Fluid Synthesis and Characterization of Pyrochlore Lead Zinc Niobate Nanopowders Derived from Zn3Nb2O8 Precursor Synthesis, Characterization and Optical Properties of a Novel Piperazine Derivative Microcrystal Microstructure and Microhardness of Copper Subjected to High Pressure Torsion Study on Pore Structure and Sulfur Fixation Characteristics of Alkali Industrial Waste Thermo-Responsive Dispersion of Multi-Walled Carbon Nanotubes Modified with Poly(N-Isopropylacrylamide-Co-Acrylic Acid) Spunbonded Nonwovens Made from Segmented Pie Filaments Fabrication of Flake-Shaped Core-Shell Micro Particles by Way of Thermal Decomposition of Pentacarbonyl Iron on Diatomite Surface Synthesis and Antioxidant Activity of Resin of Chitosan Cerium Encapsulated Green Tea Extract Microspheres Fabrication of Micro-Silicon Filter and Separating of Blood Cells Carbon Nanolines Grown on Carbon Cloth Prepared by a Two-Step Method Synthesis of Nano-Strontium Titanate Immobilised on the Silica Gel G and its Application in Removal of Heavy Metal Ions from Water Synthesis and Characterisation of Bicone-Shaped and Monodispersed Nanoparticles of Cu2S Research on Cement Pulverized Admixture of Waste Concrete Powder Preparation of Porous Nano-Strontium Titanate and its Application in Removal of Heavy Metals from Environmental Water A Facile Method for Fabrication Zinc Oxide Nanoparticles with Green-Photoluminescence Preparation and Characterization of Thermo-Sensitive Hydroxypropylmethyl Cellulose/Poly (N-Isopropylacrylamide) Hydrogel Dihexadecyl Phosphate-Assisted Synthesis of Unusual Calcium Carbonate Microspherules Characterization of Well-Dispersed CeO2 Nanoparticles Prepared by a New Method of Reverse Microemulsion Hydrothermal Synthesis and Characterization of Novel MoS2 Nanoflowers Directed by Ionic Liquid The Effect of Biology Activity on WS during Anaerobic Digestion Solvothermal Synthesis of Cd1-xZnxS (x = 0-1) Nanorods Using Single-Source Molecular Precursors Leaching Behaviour of Heavy Metals from the Class C Fly Ash-Based Geopolymers Effects of Bentonite Clarificants on Organic Acids Contents in Red Wine during Clarification 3. Building Materials Performance Tests of Surface Burning for Firestop Materials Preparation and Charcterisation of PSt/GMA/DVB Microspheres by Soap-Free Emulsion Polymerization Petal-Like Morphology on the Surface of Porous Anodic Alumina Influence of Fly Ash on Crack Resistance of Mass Concrete Application of an Anisotropic Material of Thermal Conductivity in Building Envelope The Concrete Structure Strengthen Technology and Engineering Application A New Fatigue Strength Measuring Method of Steel Bar in Concrete Study of Rubber Asphalt Modification Mechanism State of the Art of Constitutive Model of Concrete Materials Based on Damage Mechanics Setting Behaviour of Phosphate Cement Experimental Investigation into the Impact of Polypropylene Fibers and SRA on the Early Crack Resistance of Concrete The Application of Carbon Fiber Reinforcement in Tunnel Second Lining Cracks The Analysis on the Mechanical Property and Durability of Carbon Fiber Reinforced Concrete In Situ Observation Microstructure Character Changes in the Carbonation Process of Hardened Cement Paste Using ESEM/EDS Synthesis and Characterisation of Tb4L3(Phen)0.75*7H2O Nanorods The Function Study of TiO2 Catalysts on Zinc Air Battery Electromagnetic Shielding Effectiveness of Cement Based Materials with Scrap Tires Wire - FeCuNbSiB Amorphous Alloy Powder Slag-Clay Foam Cement as Roof Material for Passive Evaporative Cooling Experimental Research on the Mechanical Parameters of Frozen Pipes under Low Temperature Research on the Pore Structure of Alkali-Slag Cement Stone Activated with Water Glass Influences of Environment Climate Conditions on Concrete Carbonation Rate Study on the Hydraulic Conductivity of Sand-Bentonite mixtures used as Liner System of Waste Landfill Numerical Simulation of The Drying Shrinkage Process of Concrete The Frost Model of Concrete in the View of Damage Mechanics Effect of Ground Phosphate Slag on the Resistance to Chloride Ion Penetration of Concrete Simulation of Fracturing Process for Heterogeneous Material under Uniaxial Compression A Study of Interfacial Transition Zone in Lightweight Aggregate Concrete Effect of Fly Ash on the Workability of Nondispersible Underwater Concrete Effect of Pore Structure of Sandstone on Hydrophilic Characteristicis Photoinitiated Emulsion Polymerization of P(MMA-co-DVB) Microspheres with Low Power Ultraviolet Light Study on Interfacial Properties of Ultra-High Performance Concrete Containing Steel Slag Powder and Fly Ash Preparation and Characterisation of a Compatilizer of PP-RTV Blends Carbon Sequestration Analysis of Wood Construction Architecture 3-D Numerical Modelling of Mesoscopic Configuration and Cracking of Concrete Numerical Simulation of Temperature and Creep of Concrete Surrounding Spiral Case in a Hydraulic Plant Material Test on Aluminum Alloy Round Pipe for Building Structure The Experimental Study on Strength of Subgrade Soil Treated with Liquid Stabilizer Comparative Study on Crack Width Prediction for Concrete Flexural Members with GFRP Reinforcement Study on the Influence of Chloride Ion Content on Pavement Performance of Base Material with Fly-Ash-Flushed-By-Seawater Microscopic Mechanism Study on Carbonation Resistance of Recycled Aggregate Concrete Influence of Cement Particle Size Distribution on Strength of Cement Paste Prognosis of Alkali Aggregate Reaction with SEM A Study for Substituting Part of Raw Materials by Bottom Ash in Portland Cement Properties of the Mortar Modified with the Styrene-Acrylic Emulsion Study on Mechanical Properties of Soda Residue / Fly Ash Composite Cementitious Material Experiments for Strength Properties of Polypropylene Fiber-Reinforced Concrete Mechanism of Preferential Adsorption of Carboxylic-Vinyl Copolymer, Hydroxy Carboxylate and Sulfonation - Polyol in Cement Hydration Process Triaxial Shrinkages Tests of Unsaturated Compacted Clay Experimental Study on Relationship between Saturation Degree and Void Ratio of Remolded Soils on Drying Path Experimental Investigation Properties on Resistance of Slag Cement Concrete to Sulfate Attack Research on Mechanical Property of Single Panel Fire-Resistant Glass with Cs+ Ion and Rb+ Ion Exchange Effects of Adhered Mortar Content on Quality of Recycled Coarse Aggregate of Concrete Experimental Research on New Concrete Air Entraining Agent Research on Application Technology of TLA Modified Asphalt Mixture Mechanical Property of Solidified Concrete by Explosion as Concrete is in Flow Pattern Preparation of Potato Starch Graft Copolymer and its Application in Functional Coatings Research on Moisture Porosity Test of Explosive Lining Materials after Long-Term Water Immersion Effect of Gypsum on Strength Development of Steam-Cured Concrete Research on Performance of Cement Stabilized Skeleton-Dense Structure Aggregate Base Course Material Mesoscopic Thermal-Mechanical Fire Damage Modeling of High Performance Concrete SEM and XRD Investigation on Mechanism of Expansion and High-Early-Strength of a Cementitious Composited Grouting Material Basalt Fiber Reinforced Concrete Experimental Study on Dynamic Mechanical Behaviour of Concrete with High Temperature Experimental Research on Performance of Anchorage of Planting Rebars with Inorganic Material in Concrete Research Status and Prospects of the Smart Concrete Preparation and Properties of New Polycarboxylate-Type Superplasticizer Researches and Application of Railway Wind-Break Wall Impact Strength Test and Numerical Fitting of Plybamboo Form The Status and Development of New-Type Wall Material The Study on the Properties of Super Absorbent Polymer in Expansive Concrete Effect of Particle Size on Expansive Behaviour of MgO-Based Expansive Agent in Cement Paste Experimental Study on the Bending Resistance Performance of GFRP Tube Filled with Steel-Reinforced High-Strength Concrete Flexural Component Calculation of Flexural Capacity of SRC Beams Strengthened with CFRP Reliability Research of RPC Low-Height T-Beam in Railway Bridge Shear Lag in Thin-Walled Box Girder with Variable Section Properties of Recycled-Cement Produced from Waste Concrete Determination of Tensile Strength of Compacted Loess by Double Punch Test 4. Metal Alloy Materials Enhancing the Toughness of Heavy Thick X80 Pipeline Steel Plates by Microstructure Control Effect of Ultrasonic Power on the Microstructure and Hardness of Commercially Pure Aluminum Recent Developments for Isochronal Transformation Kinetics Model and their Applications The Kinetics of the Austenite-Ferrite Phase Transformation of Fe-4Cr Alloy during Continuous Cooling Plastic Strain Energy in Low-Cycle Fatigue of A356 (Al-7Si-0.4Mg) Aluminum Alloys Microstructures and Hardness of Silver Alloys after Internal Oxidation Process Effects of Erbium Addition on the Corrosion Resistance and Microstructure of AZ91 Magnesium Alloy Effect of Solution Treatment Temperature on Microstructure and Mechanical Properties of Cr20Ni32AlTi Alloy Study on Interaction between Cerium and Arsenic Flow Stress Behaviour of TWIP Steel during the Hot Compression Deformation Discussion on Relationship between Viscosities of Molten Zr-Cu Based Alloys and their Glass Forming Ability Forecast and Analysis of Transformation Point of TC6 Titanium Alloy Effect of Cr and Zr Addition on the Corrosion Behaviour of Copper in the Chloride Solution Effect of High Pressure Heat Treatment on Microstructure and Corrosion Resistance of Brass The Influence of Deformation on Dechromization Corrosion of CuCr Alloy in H3PO4 Solutions Effect of Element Re on Creep Behaviour of a Single Crystal Nickel-Based Superalloy Microstructure and Properties of Cu-17Fe Alloy Aged Treatment in High Magnetic Field Characterization of Precipitates in Bend-Age-Formed 2124 Aluminium Alloy Effect of Composition and Temperature on the Formation of Delta Ferrite in the Billet for P92 Steel Effect of Trace Boron on Microstructure and Mechanical Properties of Ti-9V-3Al-3Cr-3Zr-3.5Mo Alloy Analysis of the Valence Electron Structures of the Strengthening Phases Al8Fe4Ce and Al4Ce in Al-Fe-Ce Alloy Effect of Sr + RE Combination Modifier on Microstructure and Mechanical Properties of Al-40 Wt% Si Alloy Microstructures and Properties of Cu-Cr-Y Alloy after Cold Worked and Aging Hot Corrosion of Cobalt-Based Alloy with (Na, K)2SO4 Coating at 900 DegreesC Mechanism of the Flux Improving the Microstructure and Mechanical Properties of AZ91D Magnesium Alloy Effect of Temperature on Recrystallisation Texture and Microstructure for Non-Oriented Silicon Steel under Asymmetrically Rolling Process16 Influence of Yttrium and Heat Treatment on Microstructure and Mechanical Properties of AM60 Alloy Study on the Thermal Fatigue Resistance of Cr17Mn10Ni3 Heat-Resistant Steel Numerical Simulation of Surface Hardened Layer of the Hydraulic Track Effects of Two-Step Aging Temperature on Exfoliation Corrosion of an Al-Zn-Mg-Cu Alloy The Influence of Thermomechanical Treatment on the Microstructure and Properties of a Wrought Al-Mg-Si Alloy Effect of Ni on Characteristics and Structure of Aluminium Brass Recrystallisation Behaviour of Cu-20Ni-5Sn Alloy Characterization of ' Precipitate Phase in Aged Mg-12Gd-2Y-0.5Sm-0.5Sb-0.5Zr Alloy A Study on Corrosion of Cast-On-Strap Alloys Displacement Based Seismic Design Method of RC Frame with Friction Dampers Effect of Ca on Microstructure and Properties of Mg-Al-Si Alloys Effects of Sb on Microstructure and Mechanical Properties of Mg-5.5Al-1.2Y Alloy Solid Solution Strengthening of Sm in Mg-10Y-1.5Sm Alloy 5. Composites Preparation and Characterisation of Al/Pb Layered Composite Materials An Analytical Method for 3-Phase Model of Electro-Magneto-Elastic Fiber Composites with Periodically Distributed Reinforced Phases Sensitivity Analysis of Static Response for Composite Laminated Plates in Hamilton System Meshless Method with Radial Basis Functions for Hamilton Canonical Equation Study on Manufacture Technology and Mechanical Properties of Three Dimensional Braided Composite Support with Irregular Shape Thermomechanical Properties and Morphology of Liquid Crystalline Polyurethane/Epoxy Resin Composites Recent Progress on Carbon Coated Lithium Titanate Preparation and Characterisation of Konjac Glucomannan (KGM)/SiO2 Nanoparticles Blend Film Effects of Particle Size and Volume Fraction on Extrusion Texture of SiCp/Al Metal Matrix Composites Experimental Research and Regression Analysis for Constant Temperature Drying of Wheat Straw Experimental Investigation on First Crack Strength and Crack Widthof Reinforced Concrete Beamsby Side-Bonding CFRP Sheets The Stability Research of Montmorillonite/Octadecyl Trimethyl Ammonium Complexes Preparation and Flame Resistance of Hydrotalcite/Epoxy Nanocomposites Containing Red Phosphorous Pressureless Sintering and Properties Investigation of Silicon Nitride Study on the Natural Fiber/pp Wrap Spun Yarns Reinforced Thermoplastic Composites Effect Of PP-G-MAH on the Compatibility of Lignin/LDPE Composites Study on the Characterisation and Photocatalysis Reactivity of TiO2/Cu Composite Particles Manufacture and Testing of a Moderate Size Integrated Marine Composite Propeller Study of the Structural Design and Capacitance Characteristics of Fabric Sensor Separable K-Canonical Formulation of Rectangular Element and Symplectic Integration Method for Analysis of Laminated Plates Rheology and Thermal Properties of Polypropylene/Poly(phenylene Sulfide) Microfibrillar Composites Preparation and Characterisation of Polyaniline Grafted Multiwalled Carbon Nanotubes/Epoxy Composite Thermodynamics on Formation of Condensed Phases during CVD Si3N4 Process with Sicl4-NH3-H2 Precursors The Effects of Particle Size-Matching Filling of Spherical Silica on the Flowability of Epoxy Molding Compounds for Large-Scale Integrated Circuits Packaging Preparation and Characterisation of Wool-Keratin Films Based on SMS Nonwovens Effects of Wood Powder on Mechanical Properties of PP/Wood Powder Composites High Quality Al2O3-ZrO2-C Slide Gate Properties Adding Si-Fe Sintered by both Nitrogen and Carbon Monoxide Atmosphere Study on High Performance Fe3Si-Si3N4-SiC Composite Preparation and its Application in Blast Furnace Electrical Conductivity and Electromagnetic Interference Shielding Effectiveness of Multiwalled Carbon Nanotubes Filled ABS Composites Application of Carbon Fiber Composite on Space Camera Frame High Performance Si-Si3N4-Sic Sagger Composite Materials Preparation and its Attack Mechanism after Usage Sliding Wear Behaviour of Cu-10Fe-3Ag In Situ Composite Thermal Conductivity Polypropylene/Aluminium Nitride Composites Progressive Damage Model of FRP Composite Laminates with Central Hole Winding of High Performance Thermoplastic PPESK Composites Using on-Line Solution Impregnation and In Situ Consolidation Structure and Properties Study of Porous Silicon Carbide Composite Based on SLA Microstructure and Properties of La-Doped Ag-SnO2/Cu Contact Material Microstructure and Compressive Behaviour of 3D Needled C/SiC Composites Study on Electron Beam Curing of APTES Functionalized MWNTs/ Epoxy Composites Effects of Stitching Reinforcement on Mechanics Behaviour of Composite Joint under Tensile Loading Preliminary Research on Interfacial Evolution Behaviour of Ti-Cu Laminated Composite Materials Effect of Carbon Fiber Felt Pretreatment on Properties of Carbon Fiber Paper Random Response and Statistic Characteristics Analysis of Random Parameters Nonlinear Systems Research on New Technology to Control Highway Semi-Rigid Base Asphalt Pavement Cracks Effects of Cold Deformation on Microstructure and Mechanical Properties of Cu-0.35Al2O3(Y) Composite Surface Analyses of High-Temperature Oxidized In Situ Synthesized Ti-40Al-2.0C Composites The Study of Existential State of Protein in Protein/Montmorillonite Complexes Preparation and Characterisation of Sulfonic Acid-Functionalized Carbon/Loess Composite Study on the Orientation Angle of the Yarns in 3D Integrated Cellular Woven Structure Antibacterial Property of Chinese fir/TiO2 Composite Characterisation of Ti-Al and Ti-Cu Laminated Composite Electrode Materials The Different Probabilistic Method for the Conservatism Analysis of Composite Structure Damage Tolerance Design One-Step Synthesis of ZnS Nanocrystals with Graphite Sheaths from a Single-Source Precursor Thermal Properties of the Aluminum Particle Reinforced Silicone Rubber Composites The Addition of Acid Treated Carbon Nanotube on the Tribological Properties of Carbon Fiber Reinforced UHMWPE Composite Investigation of Microstructure and Property of the Fe3Al/Al2O3 Composites Fabricated by Mechanical Alloying Process and Plasma Active Sintering Process On the Improvement of Fiber Reinforced Concrete through Surface Modification of Polypropylene by Grafting Method Interlaminar Fracture Toughness of Composite Laminate with Splicing Plies Synthesis of B4C/Al-B4C/TiB2 Composite with a Two-Layer Structure Preparation and Properties of Tapioca Starch-Banana Fiber Composites Modified with Magnesium Hydroxide Seismic Reliability Analysis of MDOF Systems Based on Odd Exponent Wavelet Fabrication Porous Si3N4 -Glass Composite by Combustion Synthesis Microstructure and Mechanical Property of an ECAP Processed Al-Mg2Si In Situ Composite by Using a Combined Route Improvement in the Thermal Shock Resistance of Zirconia Ceramic by the Addition of Aluminium Titanate Mechanical and Tribological Properties of PTFE Composites Filled with POB Effect of Sintering Temperature on Al2O3/TiAl Composite from Ti-Al-TiO2-Eu2O3 System Microstructure and Mechanical Properties of Al2O3/Tial In Situ Composites Doped with Cr2O3 Tensile Property of the Flax/Polyester Composites after Water Treatment Effect of Molar Ratio of Al2O3 to Fe2O3 on the Sintering and Thermal Shock Resistance of Al2O3-Fe2O3 Composite Preparation and Characterisation of Polyborazine as Novel Precursor to Boron Nitride Ceramic Effect of Sintering Temperatures on the Sintering Performance and Thermal Shock Resistance of MgO-Al2O3-Fe2O3 Composite Properties Research of Cotton Fiber Reinforced Gypsum Based Composites Research on Oxidation Reaction of AlN Powder Microstructure and Mechanical Properties of High-Strength Graphite Particles Coated TiO2 Film Embedded in SiC Composite Mechanical and Tribological Properties of Phenol Formaldehyde Resin Reinforced with Nano-Silica Finite Element Analysis and Experimental Investigation of Carbon Fiber Composite Circular Tube Research on the Flexural Behaviour of Reinforced Concrete Beams Strengthened with CFRP Microstructure of In Situ Tic-Mo-Ni And Tic-WC-Mo-Ni Cermets Synthesized by Reactive Hot-Pressing Sintering Microstructure Characterisation and Mechanical Behaviour of 2D C/SiC-C Composite with SiC/PyC Multilayer Matrix Dynamic Effective Properties of Particle-Reinforced Composites with Imperfect Interface Microstructure and Mechanical Properties of In Situ WC Particles Reinforced Iron-Based Composite Coating Preparation and Characterisation of TiO2-Supported on the Surface of SiO2 Wood-Polymer Composite Prepared by Combined Two-Step Method and its Dimensional Stability Chemical Modification of Poplar Wood on the Mechanical Properties Influence of Hydrothermal Environment on the Composite Laminate Plate with a Hole Three-Dimensional Effective Elastic Moduli for Multidirectional Filament-Wound Tube with Lining Effects of Fe on Friction and Wear Properties of Cu-Based Friction Aterial Study on Porous Structure and Surface Characteristics of Al-Pillared Montmorillonite A Study of Ramie Fiber Reinforced Polypropylene Composites Preparation and Performance Study of Carbon Fiber Reinforced ABS Modified Nylon Resin Base Composite Material Characteristic of Raman Spectra, Crystal Structure and Superconductivity of Fe-Doped GdBa2Cu3-xFexO7- Systems Design of the Stitching Parameters Applied to the Laminates with Cut-Out Experimental Study on the Axial Behaviour of Cold-Formed Thin-Walled Steel Framing Wall Studs Experimental Study on Applying Bentonite for Mango Storage Study on Preparation Technique of SiC/Cu-Al Composite by Pressureless Infiltration A Study of Test for Polyethylene / Modified Montmorillonite Nanocomposites In-Plane Anisotropic Mechanical Properties of Three-Dimensional Angle-Interlock Architectural Composites 6 Earthquake Resistant Structures, Materials and Design Parametric Study of Hysteretic Behaviour of Combined Welded Heavy Steel Plates with Accumulative Damage TRIZ and its Application in Industrial Design Shear Strength Upgrade of Perforated RC Shearwalls Using Prestress and Steel Plate Nonlinear Finite Element Analysis of Shearwalls with Various Types of Openings Seismic Performance of CFRP Strengthened Unreinforced Masonry Structures The Effect on Scattering of SH-Wave in a Layered Half-Space with the Subsurface Circular Cavities The Dependence of the Corrosion Resistance of Ni-Cr-Mo-Cu Alloy to H2SO4 Solution on the 4Cr/ (2Mo+Cu) Study on Properties of Foam Concrete Based on Fractal Theory The Dependence of the Corrosion Resistance of Ni-Cr-Mo-Cu Alloy to HCL Solution on the 4Cr/ (2Mo+Cu) Dynamic Analysis of Steel Tube and Concrete-Filled Steel Tube High-Limit Protection Racks under Impact Loads Research on a New Type of Rolling Ball Isolator Experimental Study of the Steel Type Buckling Restrained Braces Analysis and Countermeasures on Seismic Damages of Gas Pipeline Network in Wenchuan Earthquake Seismic Isolation Effect of a Tunnel Covered with Expanded Polystrene Geofoam Seismic Damage Analysis on Water Supply System in Wenchuan Earthquake A Comparative Study on Seismic Reinforcement Test of Beijing Rural Brick Building Experimental Research on Seismic Behaviour of Low-Carbon Construction Materials RAC Frame Columns Analysis for Seismic Response of Long Span Rigid Frame Bridge Collision Analysis of Protection Frame for Height Limit and Over-High Trucks Comprehensive Evaluation of Construction System on Steel Structure Housing Research on the Application of Periodic Truss-Core Structures to Structural Design of Machine Tool Finite Element Analysis of Air Cooler Used in Nuclear Power Station Seismic Behaviour on Composite Strengthening for Existing Reinforced Concrete Short Columns Modal Comparison and Bridge-Type Optimization of Light-Rail Box Girder Bridges Research on Semi-Active Control of Large-Scale Aqueduct Comparative Study on the Pseudo-Dynamic Testing of Semi-Rigid Connection of Steel Frames with or without Brace A New Seismic-Isolation Device Applied in Continuous Beam Bridge The Seismic Behaviour of the Materials Used in the Steel-Plate Shear Walls with Concrete Filled Steel Tube Columns Dynamic Responses of RC Underground Subway Station and Soil during the Strong Earthquake 7. Tooling Testing and Evaluation of Materials The Evaluation of Organic Coating with Artificial Defect Degradation with EIS Measurement: Phase Angle at High Frequencies The Micro-Mechanism Analysis on Rock Creep Damage Dynamic Fracture Toughness Test and Evaluation for S135 Drill Pipe Effect of Salt in Aqueous Solution on the Swelling and Water-Retention Capacity of Bentonite Surface Characterisation of the Corundum-Route Lead Magnesium Niobate Ferroelectric Ceramics The Photocatalytic Characteristics of TiO2 Films: an Expeditious Evaluation Applying Ultrasonic Testing to Detect Hole Defect Near the Surface 8. Waste Engineering and Management Treatment and Disposal of Municipal Sewage Sludge and it's Resources Utilization as Construction Material The Physical and Chemical Properties of Fly Ash fom Municipal Solid Wastes Incineration A Review on the Treatments and Minimization Techniques of Stainless Steel Pickling Sludge A Study on the Continuous Manufacturing Technique of A-Gypsum Experimental Study of Glass Ceramics from Liquid Hematite Slag Study of Fluorgypsum Modification Using Thermal Analysis Studying Reaction Process of Forsterite with Iron Ore Tailings Study on Clean Treatment of Urea-Formaldehyde Waste Using Fast Pyrolysis The Microstructure and Properties of Restored WCP/Fe-C Composites Recycling and Characterisation of Amorphous Silica from Zr-Containing Silica Residue Gallium and Arsenic Recovery from Waste Gallium Arsenide by Wet Refined Methods Hydration Characteristics and Cementious Properties of Pyrolytic Steel Slag Research on Kitchen Waste Disposal Equipment and Technology Effect of Brown Corundum Dust Powder on the Sintering Performance of Corundum-Silicon Nitride Castable The Preparation of High-Strength and Micropore Lightweight Bauxite Aggregate by In Situ Polymerization and Decomposition Mineral Sequestration of CO2 Using Basic Oxygen Furnace (BOF) Steelmaking Slag Thermodynamic Analysis on Separation Process of Iron and Niobium for Iron Tailings Containing Niobium Effect of Microwave-Treatment Power on the Properties of Activated Carbons as Electrode Materials for Supercapacitors Shrimp Waste Fermentation Using Symbiotic Lactic Acid Bacteria Preparation and Characterisation of Amorphous Silica from Alkali Wastewater Produced in Manufacturing Process of ZrOCl2 Study on Desulfurization and Denitration of with Industry Solid Waste by Microwave Thermodynamics of Slag Formation in Multi-Component Oxide Systems in Thermal Processing of Incineration Bottom Ash - Equilibrium Phase Relation in CaO-SiO2-FeOx-MgO System In Situ Synthesis of -Sialon Powder from Fly Ash A New Interior Plywood Adhesive Based on Oil -Tea Cake Study on the Hydrolysis of Corn Stalk and Photosynthetic Bacteria Group Fermentation Hydrogen Production 9. Other Related Topics Numerical Simulation of High Inner-Pressure Hydroforming of T-Branch Tube The Die Design of Large Diameter Tee Multi-Pass Extrusion Process Velocity Optimization on Squashing and Bending Process of Large Diameter Elbow High Anticorrosion Nano Zn-Fe Coatings by Pulse Electrodepositing Reverse Engineering Application in Automobile Parts Design Molecular Dynamics Simulations of Structures of Amorphous Carbon Films via Deposition / Phase Transformation in Porous Reaction-Bonded Silicon Nitride Ceramics Analysis of Characteristic of Microstrip Signal Loss in Course of Signal Transmission Structures and Properties of ZnO-Based Ceramic Films for Low-Voltage Varistors by the R.F. Magnetron Sputtering Synthesis of Aluminium Diethylphosphinate by Gas-Liquid Free Radical Addition Reaction under Atmospheric Pressure Comparative Study of GaN-Based LED Grown on Different Substrates Influence of Dope Concentration on Morphology And Properties of Cellulose Hollow Fiber Membranes Prepared from Cellulose/[Amim]Cl Dope Solution Study of Mg(Zr0.05Ti0.95)O3 Dielectric Thin Films by Sol-Gel Method Fabrication of Ti-Doped ZnO Thin Films by Chemical Bath Deposition Research on ZnS Buffer Layer by RF Magnetron Sputtering for Cu(In,Ga)Se2 Solar Cells Preparation and Characterization of Radar Wave Absorbing CB/PP Fibers Electromagnetic Properties of Polyaniline Co-Doped with CSA and Ni2+ Electrical and Optical Properties of Indium and Aluminium Doped Zinc Oxide Films Prepared by RF Magnetron Sputtering Analysis of T-Peel Weld-Bonded Joint with Single Overlap Support Effect of Aging Treatment on Microstructure and Wear Behaviour of a Nickel Based Hardfaced Coating Surface Characteristics of Ni-Mn-Fe-Ga Sputtered Thin Films Preparation and Characterization of Ce-Implanted TiO2 Thin Films Preparation and Characterizaion of Hydrophobic Transparent Hard Sol-Gel Nano-Composite Films Dependence of Film Thickness on Properties of Al Doped ZnO Thin Films Effect of Film Thickness on the Structural and Physical Properties of CdZnTe Thin Films Preparation of C60 Thin Film and Investigation of its Optical Properties Preparation and Dielectric Measurement of Pb(Zr0.95Ti0.05)O3 Ferroelectric Films Research on Reflectivity per Wavelength by Foaming Ratio of Plastics and Optical Characteristics Effect of Sulfuric Acid /Sodium Hydroxide /Sodium Chloride on Properties of Polyurea Stability of AZO Thin Films under the Environment of Hydrogen Plasma Effect of RF Sputtering Power on the Structural, Optical and Hydrophobic Properties of SiNx Thin Film Study on the Properties of LDPE/POE/Zeolite Molecular Sieves Composite Film Nonisothermal Crystallization Kinetics of HDPE/UHMWPE/n-HA Composites Preparation and Electrochromic Characterization of Nanocrystalline Nio-Base Thin Films Manufacture of Non-Toxic Lava from Recovery of the Incineration Ash by Plasma Fusing Technology Effect of a Thin Cr Layer on the Microstructures and Fracture Behaviours of Copper Films Evaluation of The Wool Fiber Surface Modified by Chlorine and Pilling Propensity of Single Jersey Growth of Double-Side Tl-2212 Thin Film on CeO2-Buffered MgO Substrate Investigation of Dynamic Stray Capacitance and Circuit Network Model for Planar Inductor with Nanocrystal Magnetic Core Effects of Heating on the Tensile Property of Soybean Protein Fibers Influence of Sputtering Power of Te and Annealing on Sb-Te Thin Films Fabricated by RF and DC Co-Sputtering Electrodeposited Crack-Free CdS Thin Films Using Organic Solvents Surface Modification of Starch and its Application in Rubber Composite with Low Heat Generation and High Fatigue Resistant The Theoretical Prediction and Experimental Verification of Modal Parameters for Carbon Fiber Reinforced Composites with Sandwich Structure The Effect of Reinforcement Structure on the Modal Parameters for Sandwich Structure Composite Plate Synthesis of Waterborne Polyurethane for Coating on HNIW Study on Analysis Methods of Tear Propagation of Fabric Laminates Fabrication and Characterization of Transparent P-Type ZnO Films Obtained by In Situ Oxidation of Sputtering Zn3N2 :Al Room Temperature Deposition and Properties of AZO Thin Films by DC Magnetron Sputtering under Different Plasma Power Analysis of Influence of Optical Electrode Geometry Effects on Manipulation Using Lateral-Field Optoelectronic Tweezers The Detection of Different Physical Properties of Laser-Damaged HfO2 Film on SiO2 Substrate by Scanning Probe Acoustic Microscope Synthesis and Characterization of one Component Heat Cured Polyurethane-Acrylate Sealants Fabrication of CaWO4:Eu3+ Thin Films via Electrochemical Methods Assisted by a Novel Post Treatment Theoretical Analysis of Thin Film Oxide as Insulator of Planar Micro-Coils Influence of Film Thickness on Dielectric Properties of (Pb0.97La0.02)(Zr0.95Ti0.05)O3 Antiferroelectric Thin Films Preparation of Activated Carbons from Lignite for Electrochemical Capacitors by Microwave and Electrical Furnace Heating Research on the Oil-Gas Permeability of Mixed Hollow Fiber Membrane Made by PTFE and PHFP Electrochemical Properties of NiO thin Film Prepared by Sol-Gel Process Effect Analysis of Ar-N2 Flow Rates on ZrNX Film by Pulsed Magnetron Sputtering Using Design of Experimental Method The Properties of Organosolv Pulp and Cellulose from Eucalyptus with MK2 Esterification over Nano Solid Superacid So42-/ZrO2-Sm2O3-SiO2

「Nielsen BookData」 より

詳細情報

• NII書誌ID(NCID): BB05941506
• ISBN:
  • 9783037850336
• 出版国コード: sz
• タイトル言語コード: eng
• 本文言語コード: eng
• 出版地: Stafa-Zurich
• ページ数/冊数: 3 v.
• 大きさ: 25 cm
• 親書誌ID:
  • BA24926058