Advances in mechanical design : selected, peer reviewed papers from the International Conference on Manufacturing Science and Engineering (ICMSE 2011), April 9-11, 2011, Guilin, P.R. China

著者

• International Conference on Manufacturing Science and Engineering
• Zeng, Jianmin

書誌事項

Advances in mechanical design : selected, peer reviewed papers from the International Conference on Manufacturing Science and Engineering (ICMSE 2011), April 9-11, 2011, Guilin, P.R. China

edited by Jianmin Zeng ... [et al.]

（Advanced materials research, v. 199-200）

Trans Tech Publications, c2011

• : [set]
• Part 1
• Part 2

注記

Includes bibliographical references and indexes

内容説明・目次

内容説明

This book describes the latest advances in, and applications of, dynamic mechanical analysis, optimization and control, mechanical transmission theory and applications, mechanical reliability theory and engineering, theory and application of friction and wear, vibration, noise analysis and control, mechanical dynamics and its applications, heat and heat engineering, etc. It provides a comprehensive survey of the latest advance, and also constitutes a valuable reference source for researchers in this field. Volume is indexed by Thomson Reuters CPCI-S (WoS).

目次

Sponsors, Committees and Preface 1 Mechanical Dynamics and Its Applications Rheological Properties of Concentrated 1-Allyl-3-Methylimidazolium Chloride Cellulose Solutions Parameters Identification and Dynamic Analysis of Linear Rolling Guide Synthesis and Characterization of Polyimides Derived from Novel 1,3-Bis(4-Aminophenoxy)Benzene Dynamic Modeling of Planar Flexible Multi-Link Manipulators with Accounting for both Link Foreshortening and Link Material Damping A Simplified Numerical Method to Determine the Loads Acting on the Cutterhead of a Compound Shield Kinematics and Dynamics Analysis of the Lifting System of a Welding and Tube-Transferring Car for Deepwater Pipe-Laying Vessels Low-Speed Dynamic Characteristics of Hydraulic Clinder Based on Nonlinear Coupling- Force Crashworthiness Simulation Analysis of Light Sport Aircraft Fuselage Structure Analysis of Particle Motion in Vertical Shaft Impact Crusher Rotor Micro Analysis in Healing Area of Inner Crack for a 45 Steel Propulsive Efficiency Analysis on C-Start of Robot Fish A New Method to Realize Unsteady Calculation of Flow in Labyrinth Seals Geometric Curve Design Method of Fuzzy Reliability Based on Random Processing Errors Study on V-Shaped Linear Ultrasonic Motor and its Experiments Rheological Behaviors Characterization and Modeling of a Novel Three-Branched Phenylethynyl-Terminated Imide Oligomer Dynamic Analysis of 64-Type Rush-Repair Steel Girder under the Moving Train Loads Load Model of Small Parameter Scroll Wrap for Bending Fatigue Strength in a Scroll Compressor Study on Design Method for Magneto-Rheological Fluid Damper Based on Squeeze Mode and Experimental Tests Phylogenetic Analysis and Microbiologically Influenced Corrosion of a Kind of Sulfate-Reducing Bacteria Elastic Dynamics Analysis and Simulation of New Tire Building Drum Shearer Load Identification of the Load Spectrum of the Pick Based on Chaotic Characteristics Tests on Mechanics Parameters of HEC Concrete and its Capabilities under Contact Blast Collision Analysis of Ship Side Failure Analysis of Flail Knife on Aluminum Scrap Impact Crusher The Dynamic Property Analysis of Ink System in Offset Press Design and Test Analysis of Precise and Fractionized Inertia System of Tire Drum Test-Bed Preliminary Studies on Carbon Sequestration Changes of Wood Materials in Manufacturing Process Force Control of a Constrained One-Link Flexible Arm with Internal Damping Simulation of Arresting Dynamics on the Carrier The Dynamic Equations and Response of Hydraulic Excavator's Working Mechanism System Study on the Microstructure and Performance of New Type Martensite Wear Resistant Steel Optimization Design of the Lawn Mowing Vehicle's Blade Based on Aerodynamics Research and Design of Small-Engine LPG Motorcycle Fuel System The Finite Element Analysis and Optimal Design to Inverted Umbrella Aerator Simulation Research on Matching of Spray and Combustion Chamber Geometry in Diesel Engine Research of Micro Free-Piston Engine Generator Performance Non-Linear Characters of Rotor System with Crack and Rub-Impact Coupling Faults Evaluation of HMA with Coal Gangue Coarse Aggregate Simulation Analysis of the Stacker Column Based on High-Speed & High-Acceleration Research on Dynamical Model of Horizontally Vibrating Conveyor The Theory and Synthesis of High Effect Flywheel with Variable Equivalent Mass Moment of Inertia All-Pose Statics Simulation and Strength Calculation of the Excavator Boom Dynamic Analysis for Derailment Safety of High-Speed Railway Vehicle Bogies Rigid-Flexible Coupling Dynamics of a Flexible Robot with Impact Dynamic Analysis of the Pipe Lifting Mechanism on the Deepwater Pipelaying Vessel Explore the Dynamic Characteristics of the Off-Road Vehicle Clutch on Release Bearing Life 2 Mechanical Transmission Theory and Applications Modeling Minimum Cutting Velocity of a Cut-Clamp Combined Litchi Picker BP Neural Network in Prediction of the Constant-Current Hydrostatic Bearing Static Stiffness Dynamic Simulation and Analysis of Parallel Indexing Cam Mechanism Based on ADAMS Catastrophe Analyses of Rock Cut by Helical Cutting Mechanism Kinetics Performance of a Linkage with Dynamic State Balance and Small Fluctuation Features Research on Planet Crumb-Free CNC Pipe-Cutting Machine Mechanical Parameters Research on the Construction Method of Intermittent Transmission Function and its Application Analysis of Isometric Modification of Spur Bevel Gear E-Bayesian Estimation Method and its Applications in Reliability Engineering Performance Analysis of Auto-Control Adjustable Speed Asynchronous Disk Magnetic Coupling Research on Automatic Mechanical Transmission Shift Schedule Software Development of Steady Numerical Computational Method of Matching between Hydrodynamic Torque Converter and Engine Study on Minimum Teeth without Undercutting of Standard Involute Gears A Study on the Development of the Korean Gauge-Adjustable Wheelset System for Freight Train Kinematics Analysis of the Wedge Clamping Device of PET Bottle Blowing Machines Experiments and Modeling of a Rotatable-Direction-Valve in Bionic Undulating Propeller Accurate Calculation on Bending Stress of the Tooth Root of the Involute Cylindrical Gear Innovation Synthesis of Basic Configurationof Epicyclic Gear Trains with Three-Degrees of Freedom The Design of Worm Wheel Transmission Error Measurement System and the Research on Experimental Method The Determination and Simulation for the Dead Zone of Opening/Closing Mechanism in the Bottom Door of the Railway Freight Cars Natural Properties Analysis of an Idler Gear System of a New NC Power Turret Computation for Output Torque of Electromechanical Integrated Toroidal Transmission Computerized Design and FE Simulation of Meshing of Involute Spiral Bevel Gears with Alignment Errors A Novel Algorithm for Enumeration of the Planetary Gear Train Based on Graph Theory Research on Elastohydrodynamic Lubrication Theory of Rolling Bearing Type Planetary Friction Transmission Mechanism Preparation and Kinetics of Wood-Based Ni-P Coating Electromagnetic Shielding Material by Ytterbium-Improved Electroless Plating Transmission Efficiency Analysis of pin-Cycloid Planetary Gearing Reducer Applying Two-Stage Speed Reduction Used in Propeller Pitch Variator Analysis of Automatic Welding Finned Tube Hydraulic System Based on Automation Studio Nickel Deposition on Pre-Electroless Plated Ni-P-B Coating on Quartz Optical Fiber in a Lanthanide Oxide-Added Watt Electroplating Bath Preparation of Pd/Ag Film on Porous Ceramic Tube by Osmosis Pressure-Assisted Electroless Plating The Systematic Design of Multi-Speed Internal Gear Hub for a Bicycle Structural Design and Analysis on Reducer with Traveling Wave Driving Principle 3 Mechanical Reliability Theory and Engineering Study of Reliability Modeling for Process System A Study on Measuring Method for 3D Motion of Balls in High-Speed Ball Bearings Time-Dependent Reliability-Based Robust Optimization Design of Components Structure Estimation of Fatigue Life for Hydraulic Excavator Boom under All Operating States Design and Force Analysis of a Roller-Type Garbage Sorting Equipment Study the Equipment Based on Fast Flood Discharge Reliability Assessment for a Certain Diesel Engine Based on Performance Degradation Data Dynamic Reliability Sensitivity Design of Mechanical Components with Arbitrary Distribution Parameters State Evaluation for Power Plant Equipment Based on Deviation of Operating Parameters Stochastic Finite Element Method Using Polynomial Chaos Expansion Design of Environmental Hardware in Car Alternator Testing System An General Method on Heat Dissipating Capacity in Multidimensional Heat Transfer Computing Method of Reliability Sensitivity under Independent Multi-Failure Modes Out-Plane Stability of Derrick of Inclined Drilling Rig Study on Reliability for Vehicle Skeleton under the Action of Road Spectrum Modern Aerotransport Line Maintance Reliability and Maintainability Index Analysis Fuzzy Optimal Design of Tower Crane Jib Reliability Assessment for Small Sample Based on Interval Degradation Data Research on Complex Structures Reliability Analysis Using Improved Response Surface Method Maintenance for Improving Manufacturing Equipments Availability Using Prognostics and Health Management Fatigue Reliability Copula Model of Structural Systems with Fatigue Life Correlation Influence of Casing Inner Wall Corrosion on Internal Pressure Strength The Actualities and Development of Fatigue Reliability Design Methods of Pressure Vessels Parameter Estimations of Inverse Weibull Distribution Iteration Algorithm for Propagation of Mixed Uncertainties in Reliability Analysis Supercritical CO2 Anhydrous Dyeing Equipment and the Static Stress Analysis of Key Components Finite Element Analysis of High-Pressure Common-Rail Injector Body A Review of Reliability Principles in Conceptual Design Application of Bayesian Method in Assessing Reliability Parameters of Mechanical Product Reliability Study of Thin Seam Hearer Cutting Unit under Multi-Condition Design of Magnetic Levitated Thrust Bearing Experiment Table Stress Analysis of Rail for an Electromagnetic Launcher due to Projectile Movement Screw Relibility Design Based on the Linear Second Order Moment Method 4 Theory and Application of Friction and Wear Effect of Counterpart's Surface Micromorphology on Tribological Behavior of Nylon under Dry Sliding Contact Fault Diagnosis for Rolling Bearing Based on Genetic-SVM Classifier Research on Preventing Deflection Mechanism of the Auger Mining Machine A Study on the Accelerated Life Test for Hydraulic Cylinders Oil Droplet Motion Considering Breakup in an Aeroengine Bearing Chamber Friction and Wear of Typical Tool Material at Elevated Temperature Preparation and Tribological Behaviors of Porous UHMWPE Using as Artificial Cartilage The Friction and Wear Behaviors of 3-(N-di-n-butylaminomethyl) Quinazolin-4-Ones in Liquid Paraffin Experimental Study on Lubrication Performance of Slide Bearing with Groove on All Pads A Finite Element Cavitation Algorithm Using Free Mesh for Mechanical Face Seal Contact Angle Model and Wettability of Regular Microsurfaces The Wear Mechanism of DLC Films at Variable Working Conditions Effect of Cylinder Surface Treatment on Diesel Engine Performance Preparation of Electroless Ni-P Composite Coating and its Tribological Properties Analysis of Piston Ring Lubrication with Different Lubricant Supply Multiple Influencing Factors Analysis for Non-Conformal Contact Characteristics of Ball Screw Dynamic Viscosity Variation of Aqueous Solutions with Polyethoxylated Ether (PEOE) Added Coupling Analysis of Frictional Heat under Control of Disc Brake Anti-Skid Brake System Simulation on the Wear Behavior of the Wear-Resistant Surfaces Using Discrete Element Method Numerical Simulation on the Lubrication Performance of Surface Textured Piston Rings Meniscus and Viscous Forces during the Nanoscale Separation of Sphere-on-Sphere Contact Surfaces A GAFCM Clustering Analysis Model for Diesel Engine Faulty Diagnosis Finite Element Analysis of the Static Performance of a Self-Slot-Compensating Aerostatic Bearing Study on the Fretting Wear Failure in the Cylinder Block of a Diesel Engine The Application of Fuzzy Mathematics in Shearer Malfunction Diagnosis Friction and Wear Characteristics of Spherical Plain Bearings with PTFE Woven Liners 5 Vibration, Noise Analysis and Control Torsional-Vibration Action Research on the Diesel Engine Crankshaft Vibration Characteristic of Shell-Shafting Coupled System Induced by Propeller Exciting Force Application of Model Based Diagnosis in Two-Span Rotor System with Two Unbalance Faults Experimental Study on Hermetically-Sealed Construction and Ether-Resistance Materials in DME Engines Determination Method of Angular Domain Resampling Order in Computed Order Tracking Analysis Effect of Blade Numbers on Aerodynamic Performance and Noise of Small Axial Flow Fan Propagation Character of the Stress Wave in Weld Joints Analysis and Design of Stator of Traveling Wave Type Rotary Ultrasonic Motor Research on the Effect of Fluid-Structure Interaction on Dynamic Response of Gate Structure Vibration Analysis of Gear Transmission System in Electric Vehicle Coupling Effects on Torsional Vibration with Clearance of a Two-Degree-of-Freedom System Investigation of Vibration on Vehicle Suspension System using Half-car-model Vibration Response Analysis of a Stepped Beam with Crack Using Composite Element Method Reducing Vibration Analysis on Travel Stabilizing System of Wheel Loader Based on ProE and ADAMS Rotor Complex Fault Vibration Analysis Based on Frequency Heterodyne EMD Method Identification of Excitation Source Number Using Principal Component Analysis The Vibration Characteristics of a Large Flexible Vibration Isolation Structure with Finite Element Analysis and Modal Test Dynamic Analyzing the Vibro-Impact System with Time-Varying Mass Analysis of the Influence of Tunnel Blasting to the Neighbor Tunnel Influences Discipline of Tunnel Blasting Vibration on 20 Floors Reinforced Concrete Frame-Shear Wall Structure Building Hollow Effect Induced by Vibration in Cross-Harbor Tunnel Modification of Surface Velocity Calculation Formula in Tunnel Blasting Investigation of Self-adaptive Vibration Suppression for a Flexible Plate with Imbedded Fluid Decoupling Free Vibration System of Bridge Section Model Application of Acoustic Emission on Fault Diagnosis of Rolling Element Bearing Gear Local Fault Diagnosis with Empirical Mode Decomposition and Hilbert Huang Transformation Study on Fault Diagnosis of Rotating Machinery Based on Lyapunov Dimension A Method of Signal-Noise Separation from Measured Vibration Response Signals Estimation of Random Sonic Fatigue Life Based on Peak Probability Density of Von Mises Stress Amplitude Incremental Complementary Energy Principle for Nonlinear Vibration of Elastic System Multichannel Vibration Fault Diagnosis for Rolling Bearings Based on QPCA and SVM Rolling Element Bearing Fault Detection Using Redundant Second Generation Wavelet Packet Transform Vibration Analysis and Optimal Design for Cab's Isolation System of Vibratory Roller An Optimization Approach of a Seeker's Optomechanical System under Random Vibration by Using Integrated Structural/Optical Numerical Simulation Dynamic Analysis for a Subsurface Elastic Cylindrical Inclusion with a Semi- Cylindrical Hill Impacted by SH-Wave Analytical Solution of Lamb Wave Scattering at Plate End Separate Control Characteristics of Electro-Hydraulic Vibrator Using a Parallel Mechanism Wavelet Method to Extract Shock Signal of Debris Flow Analysis of Vibration Mode of Hydraulic Gate Structure Dynamic Response of Complex Structure in Half Space Study on Modal Properties of Continuous Active Structures Analysis on Bistable Response of a Disk-Rod-Fastening Rotor A Simulation Research on the Noise and Flow of Vehicle Cooling Fans An Experiment Investigation to the Effect on Measurement Precision of Torsional Vibration Numerical Modeling and Simulation of Random Road Surface Using IFFT Method The Experiment Research on Related Factors of Influencing Combustion Noise of Diesel Engine Study on Dynamics of the Bionic Mechanical Coupled Diaphragms for Sound Source Localization Automotive Interior Noise Analysis and Optimization Subjected to Different Road Excitations Fault Diagnosis Based on Acoustic Emission Signal for Low Speed Rolling Element Bearing A Study of the Herschel-Quincke Tube Concept Fault Diagnosis for Low-Speed Rolling Bearing Using Stress Wave and Wavelet Analysis Study on Active Control of Structural Frequency Response Vibration Isolation with Semi-Active Friction Damping Test Verification of a New Type Damper for Piping System Tribological Properties of Serpentine Nanoparticles as Oil Additive under Different Material Friction Pairs Analysis of Transverse Vibration of Circular Plates with an Elastically Mounted Mass Based on Combination of GDQM and FEM 6 Mechanical Dynamics and Its Applications Dynamic Structure Design of Large-Scale High-Speed Gantry Type CNC Milling Machine The Nonlinear Magneto-Elastic Vibration and Stability of Current-Conducting Thin Plate in Longitudinal Magnetic Field Adhesion Control of High Speed Train under Electric-Pneumatic Braking Nonlinear Superharmonic Resonance of Damped Circular Sandwich Plates with Initial Deflection Research of Nonlinear Primary Resonance of Damped Circular Sandwich Plates with Initial Deflection Research on Fabrication Techniques and Performance Analysis for 3x3 Cymbal Transducer Array Based on Preference Front Wheel Alignment Parameters Robust Design Response Analysis at Near Critical Point of Hopf Bifurcation in Nonlinear Systems Optimization Mathematic Model of the Arrangement of Aiguilles Cutting Picks The Analysis and Experiment Study on a New Driving Structure of Piezoelectric Vibration Feeder Dynamic Analysis of Communication Cabinet Structure Design Research on Optimization for the Piston Pin Additional Acceleration on Spacecrafts and Corresponding Theory for Aeronautic Manufacturing and Space Shuttle Design Modal Analysis of the Cabinet of a Drum Washing Machine Bearing-Rotor Coupled System Stability Optimization Design Based on Genetic Algorithm Study on Control Method of Smelting-Pool Width in TIG Welding Basded on Fuzzy Control Application of ANSYS Secondary Development in Magnetic Density Analysis of Permanent Magnet Synchronous Motor Design a New Type of Interfered Muffler Based on Pneumatic Tools The Influence of Crack on the Sound and Vibration Characteristic of Gear Structure Discussion of the Passive Shuttle-Type Control Technology Decreasing the Accident of the Nuclear Power Plant Performance Optimization and Comparison of TMD, MTMD and DTMD for Machining Chatter Control Experimental Research on Influence of Loading Method on Dynamic Behavior of Recycled Concrete Optimization Design of Tank Structure for Semi-Trailers Study on Multi-Objective Optimization Design of Planetary Gear Reducer Modal Stiffness Contributions of Components to Full Truck Heat Load Analysis of Piston Based on the ANSYS Optimization Design of Piston Head on ANSYS Simulation Analysis of Crash Tests for the Front Side Member in LS-DYNA Dynamic Analysis for the Viaduct Type of Longmen NC Engraving and Milling Machine Application of Two-Port Network in Bilateral Control for a Haptic Interface with Force-Position Compensation The Robust Optimization Design for Breaking Spring of Spring Actuator of Vacuum Circuit Breaker Structure Optimization of Slip by the Combination of Artificial Neural Network and Genetic Algorithm Modeling and Co-Simulation for Hydraulic System of Test-Bed of Semi-Automatic Coupler Draft Gear Based on AMEsim/Simulink A Simple Synthesis Method for Spherical 4R Linkages Reaching Four Positions A Synthesis and Optimal Method for Straight Line Mechanism with Burmester Points The Obstacle-Surmounting Process Simulation of Arm-Swing Wheeled Robot Based on MATLAB Optimization Design of Beam Pumping Unit Based on Response Surface Method Optimal Design of Bogie Parameters Determination Test Bench Gantry Framework Based on SolidWorks/Simulation A Numerical Integration Method of Dynamic Finite Element Analysis Model and Simulation of Three-Section Crossbeam Based on Experimental Data The Structural Analysis and Rapid Optimization for High-Speed Spindle Box Dynamic Analysis and Experiment of Beamlike Space Deployable Lattice Truss Optimal Control Discipline Research of Hydraulic System of Sugarcane Harvester Modal Analysis of Cracked Plate Using Interval B-Spline Wavelet Finite Element Method Integrated Design of Materials and Structures with Scale-Coupled Effect A Topology Optimization Method in Fuselage Flutter Model Design Multi-Dimensional Optimization of Groove Parameters in Gas Film Seal Modal Sensitivity Analysis of PCB The Research on Kinematics and Optimized Design of a Novel Parallel Mechanism with Six Freedoms Structure Improvement of the Principal Axis of a CNC Vertical Boring-Milling Machine The Impact Effect Study Due to The Suspender Break in Through Arch Bridges Multi-Objective Inversion Design of Cutting Head by Hard Rock Boring Machine Based on Fuzzy Theory and Genetic Algorithms Analysis of Energy Absorption in Cutting Processes of Roll-Over Protective Structure of Engineering Vehicle Finite Element Analysis of Static Characteristics of a Hydrostatic Guideway and its Effect Factors Analysis of Seismic Vibration Reduction of Latticed Shell with Bucking Restrained Braces Optimization Design of Three Helical Tooth Star-Wheel Loading Mechanism Based on ACO Dynamic Characteristics Simulation of Luffing System for Aerial Work Platform Truck Based on Matlab/Simulink Analysis and Simulation on Dynamic Stress of Tracked Vehicle Sprocket Based on Rigid-Flexible Coupling The Numerical Simulation and Experiment on Temperature Field in ICF Driver's Target Building Optimization Design of Walking Beam Based on Stiffness Constraint Overhang Effect on the Contact State between the Three-Point Bending Specimen and Supports in Hopkinson Bar Mechanical Structure Optimal Design of 3D Non-Destructive Measurement System The Solution of Problems in Cast Iron Dryer End Covers Designing Dynamical Analysis on Sugarcane Cutter Rigidity Enhancement Dynamics Research of Ultrasonic Peristaltic Micro-Fluid Driving Model Method of Compensation Control for Shaking Table Prioritizing Design Configurations of Vertical Grinding Machines Considering Static and Dynamic Performances Modeling of Load Distribution in Large-Size Wind Turbine Blade Bearings An Optimization and its Realization of Mast Crane Based on APDL Kinematics Analysis of 6-DOF Transportation Vibration Platform A Study on Test Technology of Ship Shafting Torsional Vibration Preliminary Study on Vertical Subsoil Participating Mass Design and Experimental Study of the Vibration Control Device for Large Spatial Structure Optimal Design of Main Parameters for Pumping Unit of Automotive Power Steering Units The NAVMI Factor and Natural Frequency of a Circular Plate Exposed to Water in Flexural Vibration Modal Analysis of Ball Mill Rotator Based on FEM Technique The Application of the Elman Network on the Vehicle Handling Stability Control 7 Heat and Heat Engineering 3D Analysis of Vibration Isolation by Wave Impeding Block in Non-Uniform Layered Ground under Horizontal-Rocking Coupled Loading Research of Gas Heater with Different Intermediate Heat Carrier Medium Study on Thermal Contact Resistance for Heat Transfer of High Power LED Packaging Analysis of Thermal Resistence for High-Power Light-Emitting Diodes Modeling for 3-D Temperature Field of Oil-Immersed Transformer Numerical Modeling and Simulation Analysis of Temperature Field of Disc Brake on Trains Study on Vibration Reduction of Finishing Lapping Machine for Bearing Race Spreading Resistance Analysis of LED by Structure Function The Impact of Hybrid Ventilation on Thermal and Energy Performance in Hot and Humid Weather Synthesis Method of Heat Exchanger Network for Distillation Device Inaccuracy of Heat Transfer Characteristics for Pin Fins Considering the Influence of Heat Radiation Numerical Investigation into Thermal Behavior of Brushless Permanent Magnet Motors Experimental Study of Pressure Drop and Heat Transfer of Heat Exchangers with LASH Baffles Quality Control of Heat-Treated Surface of 20CrMo Steel Transmission Countershaft Comparisons on Flow and Temperature Fields for Water-Collecting Box of Diesel Exhaust System The Optimal Structural Parameters of Embedded High-Power Microwave Components Based on RSM-GA Characteristic and Forecast of the Error Cell on Machine Tool Dynamic Thermal Equilibrium Test and Analysis of the Small Gasoline Engine Thermal Design and Analysis of a Satellite Borne Electronic PCB Study on Kinematics Simulation of 3-TPT Parallel Machine Tool Based on Pro/E Three Point Suspension Converter's Mechanical System and Elastic Friction Vibration Principle Analysis Macro-TG Reactor and Thermogravimetric Analysis for Cooking Oil Tar Samples Experimental Investigation on Flow Boiling in Micro-Channel with R32/R134a Optimization Methods and Application Research of Stator Cooling Pipeline in High-Speed Grinding Wheel System Digital Design of Planetary Gear Mechanism of Thin Seam Shearer Cutting Department Analysis of Formed Platelet Thermal Wrinkling in Platelet Transpiration Cooling Finite Element Analysis on the Influence of Back-Up Ring on the Sealing Effect of Rubber O-Ring Extinction Thread to Infrared Lensdissipation Stray Light Research A Heat Transfer Model of Dropwise Condensation Underneath a Horizontal Substrate Transfer Heat Mechanism of Oil-Gas-Water Three-Phase Flow in Pipeline Anisotropic Heat Analysis Using Hybrid Finite Element Model with Element Boundary Integrals Simulation of Drive System for some Type of Amphibious Armored Vehicle Based on AMESim Finite Element Analysis on Frame-Type Hydraulic Press 8 Materials/Mechanical/Multi-Disciplinary Engineering Education Study on Practice Teaching of Engineering Colleges or Universities Innovation Design in Machine Theory for Mechanical Engineering Education Persist in Cultivation of Engineering Drawing Ability & Improve Ability of Students' Engineering Practice Application of ADAMS in Course Teaching of Mechanism Reform of Mechanics Education Based on the Network Teaching and Competition Team Construction of Adjunct Graduate Tutor of Mechanical Engineering in Local College The Application of Virtual Prototyping Technology on On-Off Pressure Mechanism of Printing Press Construction and Practice of the Advanced Manufacturing Engineering Training Platform Based on Network Cost Accounting Game Model for Education and Operating Method Analysis of the Cultivation Mode of Chinese Exemplary Engineering Innovators Study of Interdisciplinary Specialized Mechanical Engineering Education The Team-individual Approach for Curriculum Design Course in the Mechanical Engineering Education The Influence of WH-II Super Set-Retarding Agent on the Heat of Hydration and Indices of Portland Cement Construct the New Type Experimental Teaching Pattern in Engineering Subject and Strengthen the Practice and Innovation Capability Analysis on Mode of Practical Teaching Link in Innovative Engineering Master Education 9 Manufacturing Enterprise Project/Engineering Management Enterprise Multi-Project Selection Evaluation Based on Fuzzy Optimal Model Management of Industrial Clusters: a Focus on SMEs Research on Residence Common Value Application of Entropy Weight Technique in Grey Relational Analysis for Scheme Optimization of Sewage Treatment Plant Study on Game Decision-Making for Manufacturing and Logistics Joint Development Analysis on the Incentive Decision of Manufacturing Logistics Outsourcing 10 Other Related Topics The Study on Crystallization Kinetics of Glass-Ceramics Containing Rare-Earth Tailings by DSC Research on the Ball Annealing Parameters of Steel Cr12MoV under the Effect of Impulse Electric Field Design of a Novel TiO2 Thin Film Device Effect of Ultraviolet Irradiation on Photoelectric Properties of Indium Tin Oxide (ITO) Thin Film Deposited by Sol-Gel Method Realization of Power Supply and Optimization in Telemetry System Research on Energy-Saving Technology in Electric Furnace Dedusting System Based on Information Fusion Image Identification for Surface Defects of Steel Ball Based on Support Vector Machine The Coupling Support Technology for Y Style Large Span Intersection in Deep Soft Rock Roadway Application of GA-FNC in Crystallizer Liquid Level Control System The Superwater Using to Control Slime Pulp in Packing Paper and Optimize Close System of Whitewater The Effect of Fiber Constitution and Beating Process on Surface Strength of Packing Paper Luminescence and Scintillation Properties of Ce-Doped YAP and LuYAP Crystals Luminescence and Scintillation Properties of Ce-Doped LYSO and YSO Crystals Investigation of Sol-Gel Technique to Prepare ITO Films Using Orthogonal Experiment High Precision Grinding Wheel Dressing Control Based on PLC A New Technology of Producing Fe-TiC Powder by Mechanical Activation-Reductive Diffusion A Home-Made Automatic Analyzer to Determine the Dissolved Organic Carbon in Seawater Effect of Chitosan Biguanidine Hydrochloride on Textile Properties of Antheraea Pernyi Silk Research of Temperature Field Simulation on Electrode Wire Wear for WEDM Features and Technology of Piezoelectric Hydrophone Electron Emission from Ferroelectric Cathode Microwave Annealing of Cold Compression Deformation Red Copper A Novel Method for Sheet Formation of Porous Spray Deposited Al-Fe-V-Si Alloy Reinforced with SiC Particles Research on Grinding Technology Optimization of Bearing Steel Ball Step Vibration Drilling for Micro Inclined Hole Research on Hot-Rolling Technics of a Nickel-Based Corrosion Resistant Alloy Study of the Effect of in-Line Induction Annealing on a Set of Mechanical Properties of TP2 Copper Tube Development of Microstructure of Semi-Solid 6061 Alloy with Method of Alternating Electromagnetic Stirring On the Deep Small Hole Machining Method of Nickel-Based High-Temperature Alloy Effect of Deformation Temperation on Dynamic Recrystallization Behavior for High-Carbon Steel Virtual Machining of Spiral Bevel Gear Based on VERICUT Microstructure and Properties of Cu-Cr Alloys Prepared by a Shortened Process and a Conventional Process Subassembly-Centered Product Assemblability Analysis Method Simulated Analysis of Flow and Deformation in Trilateral Constrained and Asymmetric Square Cup Deep-Drawing Influence of Fining Temperature on Glass Qualities Determination of the Weights of Evaluation Indices with Combined Weighting Model for Engineering Materials A Methodological Study of the Enhancement of the Bid Success Probability for the Bidder Strain Gradient Finite Element Analysis of Size Dependence of Thermal Stresses in Through-Silicon Vias (TSVs) Cold Extrusion Process Analysis of "Seven-Speed Sleeve" and Forming Parameter Optimization Effect of M-ZrO2 on Sintering Behavior and Thermal Shock Resistance of Dense Cr2O3 Material Research on Print-Through and the Prejudging Model Based on the Color Difference Evaluation Effect of Cu/In Ratio on Properties of CuInS2 Films Prepared by Ultrasonic Spray Pyrolysis Method Preparation of Bauxite-Based Homogenized Mullite Grogs with Bauxite and Coal Gangue Research on Flow Stress for 00Cr12Ti Stainless Steel Microstructure and Anti-Corrosion Properties of Arc-Sprayed Aluminum Coating in Splash Zone Microring Resonator Chemical Sensor Based on Si3N4 Waveguides In-Process Monitoring and Prediction of Surface Roughness in CNC Turning Process Effect of Surface Free Energy and Electrochemical Polarization on Attachment of Sulfate Reducing Bacteria Light-Colored and Organosoluble Fluorinated Polyimide Derived from 1,2,3,4-Cyclobutanetrtracarboxylic Dianhydride Effects of Rare Earth on Electrochemical Corrosion Behavior of Graphite-Like Carbon Coatings Curved Layer Fused Deposition Modeling in Conductive Polymer Additive Manufacturing High Temperature Deformation Mechanical Model and Processing Map of Ti-6Al-2Zr-1Mo-1V Alloy Research on Milling Stability Using CNC Small Size Tool The Preparation and Application of Chitosan Derivatives for Ni Coating on ABS Development and Validation of Mathematical Model for Gas Transmission through Thin Film

「Nielsen BookData」 より

詳細情報

• NII書誌ID(NCID): BB05942010
• ISBN:
  • 9783037850374
• 出版国コード: sz
• タイトル言語コード: eng
• 本文言語コード: eng
• 出版地: Stafa-Zurich
• ページ数/冊数: 2 v.
• 大きさ: 25 cm
• 親書誌ID:
  • BA24926058