Frontier in functional manufacturing technologies : selected, peer reviewed papers from the 2nd International Conference on Functional Manufacturing Technologies (ICFMT 2010), Aug.6-9 2010, Harbin, Heilongjiang, China
著者
書誌事項
Frontier in functional manufacturing technologies : selected, peer reviewed papers from the 2nd International Conference on Functional Manufacturing Technologies (ICFMT 2010), Aug.6-9 2010, Harbin, Heilongjiang, China
（Advanced materials research, v. 136）
Trans Tech Publications, c2010
- : pbk.
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
These special volumes are intended to communicate the latest progress made and research advances in theory, technology, methods, equipment etc. within the field of advanced manufacturing technology, and to review the updated technological and research trends driving international communication and cooperation on production, education and research in the field. The major topics covered by the special volumes include Anti-fatigue design and anti-fatigue manufacturing, manufacturing systems and reliability, processing detection and monitoring-control, CIMS and management systems, production system and simulation technology, quality control of manufacturing systems, agile manufacturing, finite-element analysis and structure optimization, digital manufacturing and robotics, rapid prototyping technology, reverse engineering technology, high-speed (ultra high-speed) precise cutting technology, ultra-precise processing technology, micro machining technology, pattern recognition technology, image processing technology, sensor and signal detection technology, non traditional machining technology, mine equipment manufacturing and technology, advanced manufacturing system and technologies and so on. The result is a veritable encyclopedia devoted to the subject.
目次
Preface
Effect of Rare Earth Ce on Casting Properties of Al-4.5Cu Alloy
Simulation and Experimental Investigations of Fiber Diameter of Spunbonding Nonwovens by Means of the Air Jet Flow Field Model
Numerical Simulation of Accumulative Forming Bipolar Plates of Fuel Cell
Low Temperature Synthesis and Luminescent Properties of Ca2SnO4: Eu3
Study on Load-Velocity Dynamic Property of Piston-Type Hydraulic Cylinder Based on SIMULINK
Study on Formability about ME20M Magnesium Alloy Sheet
Effect of Adding Er on Interfacial Reactions between Sn-3.0Ag-0.5Cu Solder and Cu Substrate
Ocular Aberrations Measurement Combined with Subjective Visual Compensation
Analysis of the Milling Distortion Due to Residual Stress Based on FEM
Research of Thermodynamics and Properties of Pb/WC-Zro2 Inert Electrodes Used in Zinc Electrodeposition
Study on Influence Scope of Shock Wave and Smoke Flow after Gas Explosion
Fabrication of Biodegradable Polymeric Micro-Analytical Devices Using a Laser Direct Writing Method
Research on Fabricating Technology of Three Dimensional Integrated Braided Composite I Beam
Simulated Annealing Genetic Algorithm and its Application in Mixed-Model Assembly Line Design
Construction of Marketing Management Information System of Travel Agency Based on Customer Relationship Management
Research on the Application of Fuzzy Neural Network in the Automobile Reliability
A Multi Agent-Based Approach for Supply Chain Network
Experiment Research of Cutter Edge and Cutting Parameters Influence on Machined Surface Roughness for High Speed Milling Hardened Steel
Study on Laser Triangulation Measurement Principle of Three Dimensional Surface Roughness
Estimation and Display of Triangular Mesh Curvature in Reverse Engineering
The Optimization for Design of the Parameters of Spiral Baffle
Feature Analysis for Milling Force of Three-Edge End Mills
The Reliability Analysis of a Vacuum Forming Mold for IC Packing Bag
A Non-Linear Flow Channel Implementation Method in Magnetic Gap Space of Magneto-Rheological Valve
The Analysis of Key Influence Factors and Application Countermeasures on Quality of FDM Prototype Model
Calculation Method for the Profile Curves of Cycloidal Pump
Effect of Alkaline Treatment of Wood Flour on Strength of Wood-Plastic Composites for Selective Laser Sintering
Application of Regression Analysis of Reliability Research in Off-Center Wearing on Well Tube and Rod of Oil Sucker
A Modified Wavelet Transform Profilometry
Simulation Study on Deep Hole Drilling Machine Hydraulic System Based on System Schematic Diagram
Study on the Green Processing of Impeller
Development of a Ring Permeability Test System
The Variable Non-Linear Flow Channel Method and Device
Research on Bearing Life Prediction Based on Three Parameters Weibull Distribution
The Study of Target Points Center Extracting and Matching in Calibration
The Prediction of Shot Peening's Surface Roughness with Premixed Water Jet Based on Neural Network
Research on Safety Protection Technology of Conventional Lathe CA6140
Preparation and Properties of Waterborne Polyurethane with PDMS Side Chain
Investigation of the Drawing Process of a Square Rod from a Round Bar by Using 3-D Finite Element Analysis
Finite Element Numerical Simulation of EDM Surface Strengthening in Gas Medium of Stainless Steel 1Cr13
The Application and Development of Microbubble Column Flotation Technology in China
Effects of Isothermal Process Parameters on the Microstructure of Semisolid Alsi7mg Alloy Produced by EPM
Study on Dynamic Fuzzy Classification of Design Proposal Based on Design Style
Analytical Study on Kinetic Characteristic of the Shell of Air-Powered Diving Pump
Study on Variant Design and Improving Technology of Complex Mechanical Products Based on Knowledge Reuse
Study of Modeling and Distortion Predicting for Multi-Frame Components
The Development of Fault Diagnosis System of Reciprocating Compressor Based on LabVIEW
The Dynamic Finite Element Analysis of Table of VM1000 CNC Machining Center
Integration Technology and Application Research on Management Information in Textile Industry
Flexible Wedge-Effect for Insect Flying and Fishtail-Effect for Fish Swimming
Study on Cumulate Function of Cut-In Impacting Disrepair with Waved-Edge Milling Insert
Preparation of V-Doped Titanium-Bearing Blast Furnace Slag and its Antibacterial Activity to Mildew
Study on Temperature Field of Different Substrate Shape in Preparing Diamond Film
Research on Fatigue Behaviors of Nodular Cast Iron QT800 by Laser Shock Processing
Numerical Simulation of Thermal Deformation of High Speed and Exactitude Thermo Grip
FTA-BN Approach to Risk Assessment of Die Casting Die and Risk Mitigation Solution in 4Ps Development Framework
Study on Atmospheric Corrosion Behaviour of Sicp/Al Composite
Experiment Research on Grinding of Optical Glass with Indigenously Developed Monolayer Brazed Diamond Grinding Wheel
Open CNC System Based on Embedded Monitoring Unit
Study on Adsorption Characteristics of Ni (II) by Palygorskite
Experimental Study on Thermostatic Cutting Nickel-Base Superalloy GH4169
Research on RFID and Vision-Based AGV Navigation
Study on Data Acquisition System for Cold Extrusion of Internal Threads Based on Virtual Instrument
The Influence of Surface Tension on Lubrication Film Thickness and Pressure
New Technology of Solospun and Prospect of its Application and Development
Study of Traction Properties of Three Space Lubricants Used for Rolling Bearing
「Nielsen BookData」 より
