Green power, materials and manufacturing technology and applications : selected, peer reviewed papers from the International Conference on Green Power, Materials and Manufacturing Technology and Applications (GPMMTA2011), July 15-18, 2011, Chongqing, China/ edited by Aimin Yang, Jingguo Qu and Xilong Qu
Author(s)
Bibliographic Information
Green power, materials and manufacturing technology and applications : selected, peer reviewed papers from the International Conference on Green Power, Materials and Manufacturing Technology and Applications (GPMMTA2011), July 15-18, 2011, Chongqing, China/ edited by Aimin Yang, Jingguo Qu and Xilong Qu
（Applied mechanics and materials, v. 84-85）
Trans Tech Publications, c2011
- : [set]
- Part 1
- Part 2
Available at / 1 libraries
-
No Libraries matched.
- Remove all filters.
Note
Includes bibliographical references and indexes
Description and Table of Contents
Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The aim of this special volume was to facilitate the exchange of information on the best practices for Sustainable Power, Sustainable Materials, Green Manufacturing Technology and Applications, etc. It provides an opportunity for engineers and scientists, in academia, industry and government, to address the most innovative research and development ideas, including technical challenges, social and economic issues, and to discuss ideas, results, work-in-progress and experience concerning all aspects of Green Power, Materials and Manufacturing Technology and Applications. The work offers the reader a wealth of ideas.
Table of Contents
Preface, Committees and Reviewers
Part 1
Chapter 1: CAD, CAM, CAE
Research on the Multidisciplinary Optimization Design Method for the Diesel Engine
Approach Toward Parametric Design of Typical Parts and Parts-Library Based on UG
Design and Study of Gate-Type Steel-Shuttering Jumbo for Tunnel Lining Based on CAD/CAE
MDO of the Transmission System Based Collaborative Optimization
The Development of Physique Monitoring CAD System Based on RBF Neural Networks
The Design of SVM-Based Fitness Consulting CAD System
The Exploration of Fuzzy Inference-Based Fitness Monitoring CAD System
The Influence of Green Therapy
Curing Kinetics of Octaepoxysilsesquioxane/MNA System
Chapter 2: Composite Design and Optimization
Structure and Properties of Regenerated Cellulose Film with Fluorocarbon Coating
Effect of Sintering Temperature on Microstructure of Porous Materials Using Iron Tailing and Shale
Effect of Zr Content on Properties of Mg-Zr PM Damping Alloys
Preparation of Corundum/Mullite Composites by Sintering
Synthesis of Ultrafine Long Afterglow Phosphor with High Brightness via Al2O3 Coating Route
Analyzing Relationship between Genetic, Geographical Factors and Protein Content of Winter Wheat at Different Regional Scales
Experimental Research of the Anodic Bonding in the Si-Glass-Si 3-Layer Structure
Influence of Depositing Parameters on Microstructure of Ni-Co Pulse Plating
Fine Particle Dispersion and Deposition in Three Different Square Pore Flow Structures
Some Research on the Medical Materials
Concrete Property Analysis with the Perspective of "5-10-14-18" and "5-10-18-22" Band Gradation
Chapter 3: Control, Constitutive Modeling and Simulation
The Application of Multi-Agent Technology in the Fault Diagnosis System of Motor Armature
Multivariate Statistical Process Monitoring and Fault Diagnosis Based on an Integration Method of PCA-ICA and CSM
A Secondary Development System on Grader Working Device Oriented to Mechanism Optimization
T-S Fuzzy Control for Maximum Power Point Tracking of Solar Power Generation Systems
Research of Single Granule and Granule Group Motion Model by DEM
Modeling and Simulation of Hydraulic AGC System in a Cold Mill
The Research on CNC Machine Tool's Position Limit Protection Equipments Based on Negative Logic Control
The Application of the Baseline and Monitoring Methodologies to the Renewable Energy for Base Stations Project
Roll Damping and Anti-Capsizing System for Ships Using Fuzzy-Extension Control Strategy
Modelling and Simulation of Phased Array Transducers Base on Advanced UT Techniques
Building New Reliable Wireless Network by Using Distributed Control
The Research on H2 Optimal Control Applied to Active Vibration Isolation
Chapter 4: Dynamics, Vibration and Time-Dependent Deformation
Research on New Machining Method that Cutting Arc Surfaces in SIEMENS840D System
Prediction of Compressive Strength of Aerated Lightweight Aggregate Concrete by Artificial Neural Network
Active Vibration Control for Lathe Based Neural Network
Influence of Structural Parameters on Mechanical Properties of Double-Block Ballastless Track
Collision-Free Trajectory Generation for Waterway Surfaces of a PDC Drill Bit
Effect of Impact Position and Initial Velocity on Structure of Collided Tanker
Experimental Research on Mechanical Calculation of Fascine Object's Underwater Falling
The Harmonic Response Analysis on Vibration System of Disc Vibration Dryer
Particle Swarm Optimization Based Dimension Synthesis of the Experimental Mechanism for Elastic Bungee Jumping Ropes
Incipient Hydrate Formation Pressure-Temperature and Equilibrium Composition for CH4-N2-O2-THF-H2O System
The High Stress Soft Coal Seam Face Prediction Sensitive Index Critical Value Research
Application and Advance in Super-Hard Tool Material
Chapter 5: Energy Efficiency, Environment Ecology
Environmental Characteristical Study on Pyrite Smelting Slag
Study on Hydrological Simulation of Jin River Based on SWAT-X Model
Numerical Simulation of the Mechanically Pumped Two-Phase Cooling Loop
Investigation on the Heat Exchange Characteristics of the Condenser for Space Applications
Experimental Investigation on the Accumulator Liquid Distribution of Mechanically Pumped Cooling System
Impact of Different Film-Cooling Modes at Trailing Edge on the Aerodynamic Performance of Heavy Duty Gas Turbine Cascade
Environmental Activity of Heavy Metals in Slags Treated by Electrokinetic Removal Technology
Reformed Hydrous-Ethanol Application in Spark Ignition Engine
Numerical Simulation of Furnace Combustion Characteristic in HTAC
Numerical Simulation of Natural Convection Heat Transfer on Microencapsulated PCM Slurries
Readout Circuit for Uncooled Pyroelectric IRFPA
Chapter 6: Green Design Technology
Optimum Design of Multi-Axle Trailer's Steering Mechanism Based on ADAMS
Discussion on the Design of a New Type Down-Hole BOP
Mechanism Implementation for a 4WID/4WIS Unmanned Vehicle
Optimal DFIG Converter Protection Design under Different Controllers
A Material Selection Model of Mechanical Products Based on Total Life Cycle Design
Recent Nanofabrication of Silicon Dioxide on Silicon Wafer Using AFM Operated at Low Temperature
Design of Material Electrostatic Test Platform
The Design of Multi-Index System on UCAC2 Catalog
The Design of Automatic Rotary-Rivet-Placing System
Chapter 7: Green Manufacturing Technology
Calculation and Analysis of Microstructure of Austenitic Steel for Supercritical Unit
Development for the Optimization Technique of the Coiling Tension in Degreasing Unit
A New Type of Pig Handling Trolley
Machining Accuracy Analysis and Error Compensation Approach with the Effects of Cutting Tool Tip's Radius in NC Lathe Machining Process
Improvement and Implementation of Numerically-Controlled Process for Edger Mill Stand
Optimization and Realization of Bridge Girder of 320/50t-22m Quenching Crane
Research on Structural Parameters of Conical Nozzle
Intelligent Prediction on the Quality of Cementing
Study on Roller Eccentricity Compensation in a Cold Mill
Study on Soft Zone of Type 420 Stainless Steel Weldment during the Induction Brazing Process
Research on Machining Methods of Turning Trapezoidal Thread for Slender Axle on Lathe
Optimum KOH Wet Etching of Cantilever Tip for Better Image Captured by Nanoeducator
Analysis of Milling Forces in Slot Milling of Aluminum Alloy with Three Flutes Cutter
Part 2
Chapter 8: Green Power Systems and Power Electronic Circuits
Application of Intelligent Data Mining Method for Traffic Forecasting
Research on Signal Timing Method of Intersection Based on RFID
Rapid Design of Low-Voltage Motor Protector Based on Axiomatic Theory
Computer Modeling for the CFG Pile in Highway Soft Foundation
Numerical Simulation of NO Conversion in the N2/O2/NO by Dielectric Barrier Discharge
Investigation of Annealing Effect on the Electrical and Optical Properties of ITO Film Prepared by Sol-Gel Process
The Design of Double Liquid Zoom Lens' Model Based on Electrowetting Effect
Study on Fault Signal Detection for PMLSM
Application Design of CAN Bus (CANOpen) for Rotary Screen Printing Machine
Experiment Platform Design cSPACE-Based for a Permanent Magnet Linear Synchronous Motor Driven Inverted Pendulum
Digital Filter Design in Power's Harmonic Wave Detection
Acquisition and Analysis on 3D Deformation of Windshield Glass in Vehicle-Pedestrian Accident
Study on the Current Application Situation and Development of E-Portfolio Based on ICT for Mechanical Components Using Genetic Algorithms
Chapter 9: Material Formulations, Evaluation, and Processing
A Study of the Microstructure and Hardness of Ti-5Al-2Sn-2Zr-4Mo-4Cr by Laser Shock Peening
Study on Intensified Bioleaching Technology by Static Magnetic Field of Chalcopyrite Tailings
Influence of Mo/Sb Co-Doping on Scintillation Properties of PbWO4 Crystal
Preparation and Properties of Polyvinyl Alcohol (PVA)/Polyvinyl Pyrrolidone (PVP) Hydrogel
Preparation of Activated Alumina Admixture
High Efficient White-Phosphorescence PLEDs by Using Water/Alcohol-Soluble Polyelectrolyte as an Electron Injection Layer
Study on the Hydrolytic Stability of Borate Ester
Preparation and Photocatalytic Activity of Laden SiO2/TiO2 Composite Photocatalyst
Modification of Polishing Putty: A Study on Inorganic Filler
The Research of Silica-Coated Chromium Oxide Green Pigment Prepared by Liquid Phase Method
Octaepoxysilsesquioxane Cured by Different Curing Agents
Chapter 10: Mechanics in Tribology and Lubrication Engineering
Drive Spindle Simulation for Continuous Rolling
A Preliminary Investigation on Friction Stir Spot Welding of Steel/Mg
Study on the Tribological Properties of Porous UHMWPE
Research on Noise Generation Mechanism of Rubber Material for Water-Lubricated Bearings
Recent Progress of Vibration Analysis on Fault Diagnosis for Rolling Bearing
Effect of Substrate Conditions on Residual Stress of Plasma-Spraying Sm2Zr2O7 Thermal Barrier Coatings
Real-Time Reliability Analysis and Optimal Distribution of the Reliability on Five-Axis Machining Center
Visual Inspection on Premature Failure of Electric Motor Bearings
Finite Element Thermo Analysis of Friction Material Enhanced by Bamboo Fiber
Chapter 11: Optical and Visual Signal
Research on Magnetic Properties of Nd2Fe14B/ -Fe/Nd2Fe14B Exchange-Coupled Trilayer Films
Two-Photon Excitation Fluorescence Lifetime Imaging Based on Time-Correlated Single Photon Counting
A Control System for Traffic Light Based on GPRS
Chemical Sensors Based on Fiber Bragg Grating
Monitoring of Microorganisms Growth Process Based on Fiber Bragg Grating Biosensor
1064 nm High-Power Broad Area Semiconductor Lasers with Electrode Pattern
High Performance 785 nm Wavelength Super-Luminescent Diodes
Research of Angled 8 Degrees Integrated 808 nm Wavelength SLDs
808 nm Semiconductor Lasers with Tailored Gain for Mode Shape
Influence of Gain Dispersion on the Propagation Characteristics of Ultrashort Optical Pulses in Distributed Fiber Amplifiers
Chapter 12: Sustainable Materials and Applications
High Performance Precast Wall Panels with Shear Transfer Provided by Carbon Fiber Grid
The Study on the Electrolyte Behavior of Aromatic Polyesters from Diphenolic Acid and Isophthaloyl Chloride
Effect of Sol-Gel Method for Medium Steel Phosphating Coating of Electrochemical Behavior
Enhanced Electrokinetic Removal of Heavy Metals in MSWI Fly Ash Assisted by Cation Exchange Membranes
Pechini Sol-Gel Fabrication and Luminescent Properties of Lu2SiO5: Ln3+ (Ln=Tb,Ce) Thin Films
The Effect of Silver Ion Catalysis on Bioleaching of Chalcopyrite Tailings
The Viscosity Measurement of Polyethylene Glycol Dilaurate
First Principle Investigation of O2 Adsorption on the LaMnO3 (001) Surface
An Analysis on Technology and Product Quality Effect of II-Powdery Emulsion Explosives
The Application of Air-Space with Mixed Emulsion Explosive in Open-Pit Mines
Modification of Asphalt by Montmorillonite
Chapter 13: Sustainable Power and Applications
Refrigerant Capacity and Magnetocaloric Effect on LaFe11.1Co0.8Si1.1BX Alloys
Effects of Mg Substitution on the Thermoelectric Properties of Ca3Co4O9-Based Materials
Calculation and Analysis on PM Thermal Characteristics Influence Performance of PMSM Based on FEM
The Trend Change of Bitumen Research: A Text Mining Analysis (2000-2010)
Design and Experimental Research of Solar Powered Water Pump System Based on Single Chip
Marine Growth Effect on the Vibration Characteristics of Offshore Wind Turbine with Jacket Foundation
Computer Simulation of Icing on NACA0015 Blade Airfoil for Vertical Axis Wind Turbine
Numerical Simulation on the Static Torque Performance of Vertical Axis Wind Turbine with Different Blade Airfoils
An Improved Differential Evolution Algorithm for Dynamic Economic Dispatch of Power Systems
Optimal Design of the Vibration Device of Block Making Machine
Analysis on Proportion and Development of Steel Workers' Hospitalization Costs
Analysis of Steel Industry Workers Abridged Life Table
Integrated Automation Monitoring System in the Application of 220kV Substation
Application of GM (1, N) Model on Slope Stability Analysis in Open Pit Mine
Chapter 14: Sustainable Power Policy and Management
Research on Energy Consumption of Screw Compressor under Load/Unload
Analysis of Energy Consumption Efficiency Based on DEA-Tobit
The Design of a Central Air Conditioning System for a Rebuilt Commercial Building
Analysis of Total Factor Energy Efficiency of Manufacturing Industry in Shandong Province Based on Malmquist Index Empirical Study
Study on Power Load Forecasting Base on Grey Prediction Model by Slip Average Method
Research on Implementation Strategies of Green Supply Chain Management
Study on Green Supply Chain Management Based on Circular Economy
Decoupling Analysis of Economic Growth and Total Primary Energy Supply for the BRICS: 1971-2008
Comparative Study on Carbon Emission and Energy Consumption of the Textile Industry in Henan Province
by "Nielsen BookData"
