Structural integrity and failure : selected, peer reviewed papers from the International Conference on Structural Integrity and Failure (SIF 2010) July 4-7, 2010, Held at the University of Auckland, Auckland, New Zealand
Author(s)
Bibliographic Information
Structural integrity and failure : selected, peer reviewed papers from the International Conference on Structural Integrity and Failure (SIF 2010) July 4-7, 2010, Held at the University of Auckland, Auckland, New Zealand
（Advanced materials research, v. 275）
Trans Tech Publications, c2011
Available at / 1 libraries
-
No Libraries matched.
- Remove all filters.
Note
Includes bibliographical references and indexes
Description and Table of Contents
Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).
This special collection of 59 peer-reviewed papers covers topics related to the fracture and fatigue of all types of materials and structures, including biological tissues, metals, ceramics, polymers, composites and thin films. This wide range of coverage will make this work of interest to those studying almost any sort of material.
Table of Contents
Preface and Organizing Committee
I. Fracture, Fatigue, Damage and Failure
An Artificial Neural Network Approach to Fatigue Crack Growth
Experimental Investigation of PMMA Fracture under Mixed-Modes I, II and III Loading
Modelling Fatigue Crack Growth near an Open Hole under Spectrum Loading Using a New Method for Elastic-Plastic Stress Calculation
Effects of Crack Size and Crack Face Interference on Shear Fatigue Crack Growth in a Bearing Steel
A Model for the Cyclic Behaviour of Steel under Earthquake Conditions
Fatigue Strength of Ultrafine Grained Copper Treated by Post-ECAP Mild Annealing
Experimental Study on Theory of Critical Distance Applied to the Prediction of Fatigue from Notches
Effects of Thermal Exposure on Microstructure and Mechanical Properties of Ni Based Superalloy GTD111
Effects of Replication on Measured S-N Curves of Metals
Fatigue Behavior of Weld-Repaired High Strength Low Alloy Steel
An Analysis of Fatigue Strength of Notched Components
Thermal Shock Properties of Ti(Al,O)/Al2O3 and TiAl(O)/Al2O3 Composite Coatings
An Impregnation Technique for Crack Identification Following Uniaxial Tension Tests
An Analysis of the Bonding Energy through Pull-Out Tests for Aerated Concrete with Various Steel Strip Geometries
Low Cycle Fatigue Behavior of Ni-Base Superalloy IN738LC at Elevated Temperature
II. Structural Integrity & Failure Analysis
Study of Local Failure of a Multi-Plate Arch Bridge by Numerical Modeling
Assembly Deformation and Stresses of Compliant Structures
Fracture Strengths of Mg Alloy AZ31B-H24 Friction Stir Lap Welds
Effect of Tool Speeds during Friction Stir Lap Welding on Mode of Fracture and Fracture Strength of Al 6060-T5 Joints
Characteristics of Electron Beam Welded Ti & Ti Alloys
Microindentation of Microencapsulated Phase Change Materials
Light Emission from a Si Based ZnO Structure
Managing Potlife through Statistical Analysis
Stress and Vibration Analysis of Motor Back Plate in HDD
Aircraft Joints: the Interaction between Corrosion Protection and Structural Performance
Residual Strength Optimisation of a Vent Hole in an Aircraft Component Using a Heuristic Method
Influence of Heat Treatment on Fatigue Strength of Drawn Steel Tubes for Small-Sized Single Pass Boiler
The Microstructure and Mechanical Properties of Ni-Based Superalloy after Service Exposure in Gas Turbine
Degradation Characteristics of Inconel738LC with Thermal Exposure
Effects of High Temperature Deformation and Thermal Exposure on Microstructure and Mechanical Properties of Co-Based Superalloy
Optimum Design for Life Extension on the End Coupling of Aluminum Hot Rolling Process
Integrity Evaluation and Dynamic Behavior of Radioactive Material Transport Cask under Drop Impact
III. Bio and Nano-Materials
Ab Initio Phonon Dispersion Curves Used to Check Experimentally Determined Elastic Constants of the MAX Phase Ti3SiC2
Failure Mechanisms of Cartilage-on-Bone Tissues and the Influence of Loading History
Processing of Layered Hydroxyapatite Ceramic Composites
Nanoindentation of Individual ZnO Nano-/Micro-Rod
Validation of BioDent TDI as a New Clinical Diagnostic Method
Effect of Heat Treatment on Microstructure and Mechanical Properties of a Ti-Mo-Zr Alloy
IV. Indentation, Thin Film, Surface Treatment & Materials Processing
Copper Coated Iron Powder Prepared by Chemical Reduction Process
Study of Preparation on the Flake Silver Coating over Copper Powder for Electronic Industry
Mechanical Behaviour of Ultrafine Grained Cu and Cu-(2.5 and 5) Vol.%Al2O3 Composites Produced by Powder Compact Forging
Friction and Wear Characteristics of SUS304 and SUS630 after Ultrasonic Nanocrystal Surface Modification
Wear Evaluation of SiCp Reinforced Al Matrix Composites Coatings
Improvement of Biocompatibility of Medical Ni-Ti Alloys through Forming TiO2 Thin Film
Mechanical Behaviour of Titanium, Ti-6Al-4V (wt %) Alloy and Ti-47Al-2Cr (at %) Alloy Produced Using Powder Compact Forging
Influence of Growth Rate on the Solute Distribution of Directionally Solidified Cu-Ag-Zr Alloy
Tensile Properties and Fracture Behaviour of Induction Sintered Ti and Ti-6Al-4V (wt %) Powder Compacts
Phase Composition, Microstructure and Thermal Diffusivity of Cu/Si Composites Sintering Temperature Dependence
Tool Wear Mechanisms during Machining of Alloy 625
Microstructure and Mechanical Behaviour of Ultrafine Grained Al-4wt%Cu-(2.5-10) Vol.% SiC Metal Matrix Composites Produced by Powder Compact Forging
Effect of Pb and Sn Additions on the Ductility of Cast AZ61 Mg Alloy
Cracking and Mechanical Strength of NaOH-Slag Geopolymers
Microstructure Evolution in Nitrogen Implanted Sapphire
V. Polymers and Composites
Fracture Toughness of Polyamide 6/ Maleated Styrene-Ethylene-Butylene-Styrene/Silicon Carbide Nanocomposites
Reliability Analysis for Inserts in Sandwich Composites
Experimental Study on Strengthening of Steel Structures with Fiber Reinforced Plastic
The Influence of Processing Parameters on the Void Content and Compressive Strength of Carbon Fibre-Epoxy Laminates
Strength and Fracture Behavior of Abaca Green Composites
Microstructure and Hardness of Ni-Cr Porous Preform Reinforced Al-Based Composites by Low Infiltration Method
by "Nielsen BookData"
