Nanomaterials and plastic deformation : selected, peer reviewed papers from the Annual Meeting of Chinese Materials Research Society, Session L, 2009, 12-17 September 2009, Suzhou, China
著者
書誌事項
Nanomaterials and plastic deformation : selected, peer reviewed papers from the Annual Meeting of Chinese Materials Research Society, Session L, 2009, 12-17 September 2009, Suzhou, China
(Materials science forum, v. 682)
Trans Tech Publications, c2011
- pbk.
- タイトル別名
-
Advances in nanomaterials and plastic deformation
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
The deformation-processing of advanced materials having ultrafine- or nano-structures, and therefore significantly improved properties, has developed into one of the most promising frontiers of materials science and technology. The present 35 peer-reviewed papers cover many aspects of Nanomaterials and Plastic Deformation and will provide a succinct introduction to the subject.
目次
Preface
I. Processing
Rapid Prototyped Nanocrystalline Copper Parts by Jet Electrodeposition
Developing Metallic Glass Matrix Composites with In Situ Crystalline Spheres through the Mechanism of Liquid-Liquid Phase Decomposition in Miscibility Gap of the Multicomponent Immiscible Alloys
Studies of Annealing Process in Severely Cold Drawn Pearlitic Steel Wires
Bulk Nanocrystalline Cu Produced by High-Energy Ball Milling
Shearing Patterns of AZ31 Mg Alloy Processed by Equal-Channel Angular Pressing via Various Route
A Comparison of Temperature-Dependent Compressive Deformation Features of Ultrafine-Grained Ti and Cu Produced by ECAP
II. Microstructure Characterization
Microstructure and Mechanical Properties of Mg96Y3Zn1 Alloy Processed by Equal Channel Angular Pressing
Effects of Si/Al Molar Ratio on Morphology of Mullite Nanocomposite Synthesized from Kaolin
Microstructures and Properties of Ultrafine Grained Iron by Rolling
Texture Analysis of Commercial Pure (Grade 3) Ti after Two-Step Severe Plastic Deformation
Microtexture Study of Warm-Rolled High Strength Interstitial-Free (IF) Steel Sheets
Solidification Structure Characteristics and Mechanical Properties of (Ag-Cu28)-25Sn Alloy Ribbons Prepared by Melt Spinning Method
The Microstructural Studies of Ag/Ni20 Fibre Composites Processed by Severe Plastic Deformation
Deformation Processing and Mechanical Properties of Cu-10Cr-0.4Zr In Situ Composite Microwires
Microstructure and Mechanical Properties of Austempered Ultrahigh Carbon Steel 1.4%C
Microstructure and Mechanical Properties of CP-Ti Processed by 2 ECAP Passes Using a 90 Degrees Die at Room Temperature
Mechanical Properties of Plain Carbon Steels with Ultrafine ( + ) Microstructures
Microstructure and Performance of Surface Nanostructure 316L Stainless Steel Induced by Wire-Brushing Deformation
III. Mechanical and other Properties
Mechanical Property of Duplex Stainless Steel with Nanostructured Layer by Surface Mechanical Attrition Treatment
Microstructure and Mechanical Properties of a 1.6C (pct) Ultra-Fine Grained Ultra-High Carbon Steel
Constitutive Model for Large Plastic Deformation of Nanocrystalline Materials
Effect of Load Direction on Tensile Yield Properties in Mg-3Al-Zn Alloy
Effect of Grain Size Distribution on the Local Mechanical Behavior of Nanocrystalline Materials
Numerical and Experimental Investigation of Strain Inhomogeneity during Cyclic Channel Die Compression
Superelasticity and Shape Memory Behaviors of Ti-25 at. % Nb Alloy Processed by ECAP and Aging
Tensile Properties and Dislocation Strengthening of Commercial Pure Titanium Processed by Equal-Channel Angular Pressing at Liquid Nitrogen Temperature
Compression Superplasticity of Ultrahigh Carbon Steel in Electric Field
Effects of ECAE and Aging on Phase Transformations and Superelasticity of a Ni-Rich TiNi SMA
Microstructures and Mechanical Properties of Fcc Pure Metals with Different Stacking Fault Energies by Equal Channel Angular Pressing
Microstructure and Properties of Ultrafine-Grained Steel Produced by Warm Compression of Martensite
Improvement of Strength of Mg-12Gd-3Y-0.5Zr Alloys Processed by Combination of ECAP and Extrusion
Erosion Wear Property of Surface Diffusion Alloyed Coatings on Magnesium Alloy
Damping Behavior and Mechanism of Graphite and Al2O3 Particles Reinforced Al Matrix Composites
Fatigue Property and Fatigue Cracks of Ultra-Fine Grained Copper Processed by Equal-Channel Angular Pressing
Electroactive Organic-Inorganic Layered Perovskite Hybrids: Steric Interaction between Aminopyridine and Trivalent Ferricyanide and Use for Electrochemical Sensing Device
「Nielsen BookData」 より