Advanced materials research II : selected, peer reviewed papers from the 2012 2nd International Conference on Advanced Material Research (ICAMR 2012), January 7-8, 2012, Chengdu, China

著者

• International Conference on Advanced Material Research
• Fan, Wu

書誌事項

Advanced materials research II : selected, peer reviewed papers from the 2012 2nd International Conference on Advanced Material Research (ICAMR 2012), January 7-8, 2012, Chengdu, China

edited by Wu Fan

（Advanced materials research, v. 463-464）

Trans Tech Publications, c2012

• : [set]
• Part 1
• Part 2

注記

Includes bibliographical references and indexes

内容説明・目次

内容説明

Volume is indexed by Thomson Reuters CPCI-S (WoS). The objective of ICAMR 2012 was to provide a forum for the discussion of new developments, recent progress and innovations in the field of Materials Science. The papers are divided into twenty-two sections, covering such topics as materials behaviour, casting and solidification, coatings and surface engineering, composites, machining technology, nanomaterials, biomedical manufacturing, sustainable manufacturing processes, manufacturing planning and scheduling, modelling and simulation, computer-aided design and engineering, semiconductor materials engineering, laser-based manufacturing and mechanical and electronic engineering control.

目次

Preface, Organizing Committee and Sponsor Chapter 1: Materials Behavior About the Study of the Springs Loaded with Uniform Radial Charge Density by Transfer-Matrix Method Adsorption Kinetics of Zn(II) from Aqueous Solutions onto Epichlorohydrin Crosslinked Chitosan Analog Computation of Forms of Uranium Presence in Aqueous Solution Bending Study for Axially Symmetric Tapping Plates with Uniform Load at All Crown by Transfer-Matrix Method Chemical and Structural Characterization of / ' Interfaces Composition Typomorphic Characteristics of Pyrite in Various Genetic Type Gold Deposits Crashworthiness Optimization of Thin Walled Cylindrical Tubes with Annular Grooves under Axial Compression Crystal Morphology of Hydroxyapatite Modulated by Glutamic Acid at Different Hydrothermal Temperatures Effect of Low Temperature Aging on Internal Friction of AA2024 Effects of Co-Existing Anions on Fluoride Adsorption onto Magnesia-Amended Activated Carbon Effects of Cu on Microstructure, Mechanical Properties and Damping Capacity of As-Cast Mg-3%Ni Alloy Effects of Eva-Hot Melt Adhesive Polarity and Rheology on 3PE Modes Evaluation of Different Geometry of Received Pulses from CdZnTe Semiconductor Detectors Experimental Investigation of the Volatilization of Asphalts under Different Conditions Experimental Study on Bending Creep Behavior of Modified Fast-Grown Poplar Wood in Uncontrolled Condition Impact Test in Working Space of Milling Center Influences of Final Processing Methods on Surface Physical Properties and Fatigue Life for Railway LZ50 Steel Investigation the Adsorption of Heavy Oil from Solution by Low-Cost Material Low Cycle Fatigue Behaviour of Al-Mg-Si Alloy AA6061 Processed by Equal Channel Angular Pressing Microstructure and Tensile Properties of Forged High Nb Containing Tial Alloy on Large Scale Monitoring Nugget Size of Micro Resistance Spot Welding (Micro RSW) Using Electrode Displacement-Time Curve Morphology Evolution and Luminescence Properties of YF3: Sm Nano-/Microcrystals Numerical Analysis of Crack Propagation in Brittle Materials under Uniaxial Compression Reaction Mechanisms of Li5La3Ta2O12 Powder with Ambient Air: H+/Li+ Exchange with Water Research on Adsorption of H2S by Modified Activated Carbon Research on Adsorption of H2S by Oil Shale Ash Research on Effect of Paper Containing OBA on Color Reproduction Structural and Electronic Properties of Pt3 and Pt3M Clusters (M=Au, Ag, Sn, Fe) Studies Regarding the Movement on the Cochleoid Study of an Inorganic Ion Exchanger Al2Ti(PO4)3.3333 Study of Circular Tapping Plates, with a Circumferential Vertical Load at the Interior Boundary by Transfer-Matrix Method Synthesis and Characterization of CeO2-ZrO2-Al2O3 with High Thermal Stability and Oxygen Storage Capacity from Pseudoboehmite Precursor Synthesis of Al1.6667Ti(PO4)3 and its Selectivity to Li+ Exchange The Experimental Study on Engineering Characteristics of Improved Clay The Flexural Behavior Study of Composites Material in Static Three-Point Bending Test The Study of Epoxy Resins Modified By PPESK The Synthesis and Ion-Exchange Property of Li+ Memorized Inverse Spinel Al2.6667Ti(PO4)4 The Synthesis of Iron Oxides with Different Phases or Exposure Crystal Planes and their Catalytic Property for Propene Oxidation Thermodynamics of Organic Dyes Adsorption onto Thermal Modified Rectorite Variation of Microstructure and Properties of Re-7075 Al Alloy after Homogenizing Annealing Chapter 2: Casting and Solidification Analysis of Thermomechanical Behavior in Continuous Casting Mould and Design of Breakout Prediction System Chiral Inorganic Solid Material Development Design of Rubberized Asphalt Concrete by Means of Coarse Aggregate Void Filling Method Effect of Physical Properties of Manufactured Sand as Fine Aggregate in Elastic and Shrinkage Properties of Concrete and Mortar Evaluation of Direct Rapid Prototyping Pattern for Investment Casting Load Carrying Capacity and Ductility of CFRP-Reinforced Earthquake Waste Filled Circular Steel Tube Columns Pier Form Selection and Parameter Analysis of Reinforced Concrete Thin-Wall High Pier Properties of Cold Pressure Welded Aluminium and Copper Sheets Shear Behaviour of RC Beams Strengthened with FRP Materials The Influence of Reinforced Concrete Beams Crack on Size Effect Chapter 3: Powder Metallurgy and Ceramic Forming A STATIC-LEACH WSNs for Hazardous Materials Monitoring Advancing Ceramics Glaze Formulation with Existing Software Technology Using Locally Available Raw Materials in Nigeria CdTe@SiO2 Particles Prepared via Reverse Microemulsion Method: A Linear Connection between Shell Thickness and Tetraethylorthosilicate Dielectric Properties of Barium Titanate Ceramics Modified by CuO in Different Methods Experimental Study of PTFE Powder Size Impact to Mg/PTFE Pyrotechnic Composition Gold Nanoparticle's Temperature Effect in Photoacoustic Tomography La and/or Y Doped TiO2: Facile Synthesis and Enhanced Photocatalysis Chapter 4: Surface, Subsurface and Interface Phenomena A Study of the Effect of the Inertia Force of the Vanes on the Performance of the Hydraulic Vane Pump with Hypertrochoid Curve in the Inner Surface of its Stator A Theoretical Study of the Internal Forces in a Hydraulic Vane Pump with Hypertrochoid Curve in the Inner Surface of its Stator Comparison Study of the Geomagnetically Induced Current Level of Power Grid in Different Latitude Corrosion Failure Analysis of L80 Oil Tube Influence of Surface Mechanical Attrition Treatment on Fretting Wear Behaviour of Ti-6Al-4V Surface Measurement of GLSI Wafer with Copper Interconnects after CMP Synthesis, Characterization and Emission Properties of a Mixed Metal Complex of Europium (III) and Terbium (III) with a Tripodal Heptadentate Schiff Base Ligand The Application of FDM in Solving Problem of Electromagnetic Field The Sliding Frictional Contact Problem in Two Dimensional Graded Materials Loaded by a Flat Stamp Transition in the Fretting Phenomenon Based on the Variabile Coefficient of Friction Chapter 5: Coatings and Surface Engineering A Two-Step Method to Prepare Stable Superhydrophobic Surface on Steel Substrates Aluminium Alloy Matrices Reinforced with Coated Particulate Silicon Carbide Comparative Solid Particle Erosion Characterization of Conventional and Nanostructured Al2O3-13wt.%TiO2 Ceramic Coatings Fabricated by Plasma Spraying Process Damage Patterns of the Hexagonal Aluminum Honeycomb Sandwich Plate Subjected to Fragment Impact Effects of Surface Pretreatment to the Properties of Aluminum Oxide (Al2O3) Cutting Tool Coated Amorphous Graphite Electroless Ni-P Coating of Cenospheres Using Copper Sulfate Activator Electron Spectroscopic Studies of Homogenous (GaMn)As Layers Fabrication and Characterization of ZnO Nanorod Arrays Grown on Nickel-Coated Polyester Fiber Influence of Addition of Tungsten-Iron Powder on Microstructure of WC/Steel Composite Coatings Optimization of Pre-Treatment Parameters before Diamond Coating Using Non-Dominated Sorting Genetic Algorithm (NSGA-II) Oxide Layer Modification of Mg-Al Alloy Coated by Plasma Electrolytic Oxidation Using Zirconia Particles Preparation and Electrochemical Characterization of an Activated Carbon Material of High Surface Area for Supercapacitor Research on Corrosion Resistance of the GTAW Joint of Duplex Stainless Steel Tribological Properties of Plasma-Sprayed 20 wt. % ZrO2-Al2O3-17 wt.% TiO2 Coatings on Plain Carbon Steel Substrate Chapter 6: Composite Materials A Method to Determine the Optimal Solids Content of TiO2 in DSSC Working Electrode Cancellation Effect in Three-Phases TiO2/(PVDF+Fe3O4) Composites Comparison of Oscillography Impact Properties between a New Type Drilling Collar Steel and 4145H Correlation of Mechanical Properties of Cast Al 3xx Alloys to Processing Variables and Alloy Chemistry Using Regression Analysis and Artificial Neural Network Techniques Effect of Rolling on Microstructure and Wear Behavior of Hot Rolled Al6061-Beryl Composites Effect of Surface Treatment on Interfacial and Properties of Water Hyacinth Fiber Reinforced Poly(Lactic Acid) Composites Effects of La2O3 and Nb2O5 Doping on the Dielectric Properties of Ba0.9Sr0.1TiO3 Ceramics Experimental Study of the Compressive Performance of Life Jacket Use Polyurethane Foam for Blast Wave Protection Fabrication and Mechanical Properties of ZrO2/Ni Functionally Graded Materials Ferroelectricity of PZT-Based Thin Films Doped with Mn and Nb First-Ply Strength of Thick Circular Cylindrical GRP Composite Shell Subjected to Static External Pressure via Finite Element Simulation and Analytical Approaches Germanium Adsorption on SrTiO3 (001) 2x1 Surface: A Density Functional Theory Study Influence of Liquid Structure Change on Microstructure and Properties of SnZnBi Solder Alloy Microstructure and Wear Property of Zn-Al Alloy Reinforced with Carbonized Rice Husks Modeling of Viscoelastic Solid Polymers Using a Boundary Element Formulation with Considering a Body Load Nucleation and Growth of Cr7C3 of Brazing Diamond with Ni-Cr Alloy in Protective Atmosphere Furnace Preparation and Photoluminescence Properties of ZnO-Covered Carbon Fibers Preparation and Properties of Halogen-Free Flame Retardant Blending Modification Polyester Preparation and Properties of Nanocomposites Based on Poly(Lactic Acid) and Modified TiO2 Preparation of Poly[4-Diacetoxyiodo] Styrene by Microwave Reactor Synthesis and Characterization of Polystyrene-Graphite Nanocomposites via Surface Raft-Mediated Polymerization Synthesis of FeC2O4-Graphene Composites and their Application in Removal Dyes Synthesis of Fullerene-Acid Conjugates Synthesis of Novel Core-Shell Structured Hydroxyapatite/Meso-Silica for Removal of Methylene Blue from Aqueous Solutions Synthesis, Characterization of Electrospun Mesoporous ZnO/SnO2 Composites Nanofibers and their Photocatalytic Property Synthesis, Characterization, and Electrochemical Properties of Mn3O4/Cr2O3 Composite The Effect of N Vacancy on GaN Doped by Fe Thermo-Chemical Evaluation of Wood Plastic Nanocomposite Two-Dimensional Modeling of Functionally Graded Viscoelastic Materials Using a Boundary Element Approach Chapter 7: Materials Forming Assessment on Screw Fixing Failure Mode for Kitchen Cabinet Particleboard Comparative Study by Numerical Analysis on the Formability of Deep-Drawn Tailor-Welded Blanks Design of Optimization Parameters with Hybrid Genetic Algorithm Method in Multi-Cavity Injection Molding Process Investigation of Deposition Parameter Effects on Energy Bandgap of Silicon Thin Film Prepared by Plasma Enhanced Chemical Vapor Deposition via Factorial Experiment PLM System for Complex-Shape Aircraft Gas Turbine Parts Preparation and Analysis of Sputtered Cu2ZnSnSe4 Thin Films Tap-Changer Sliding Gear Urgent Stop Device of Main Transformer Integrated with RTU The Effect of N2 Gas Pressure during the Rapid Thermal Process on the Structural and Morphological Properties of Cigs Films The Finite Element Simulation of Lamb Wave Propagation in a Cracked Structure with Coupled Filed Elements The Influence of Annealing Temperature on ZnO Thin Films by Oxidating Zinc Films Deposited with Magnetron Sputtering Unified Stresses Solution for Sheet Forming Chapter 8: Machining Based on ABAQUS Five Axis Milling Process Dynamics Modeling and Analysis Comparison of Different Residual Stress Models of FSW Butt Joints for Thin Aluminum Alloy Plates Contour Errors during Milling Process Development of an Efficient Haptic System for Tooth Processing Discussion of Nonlinear Constitutive Models for Aluminium Alloy Material Engine Piston Estimation and Optimization Cutting Conditions of Surface Roughness in Hard Turning Using Taguchi Approach and Artificial Neural Network Oxidation Behaviors of Dusts Generated in Different Cutting Processes of Silicon Ingots Prediction and Optimization of Dimensional Shrinkage Variations in Injection Molded Parts Using Forward and Reverse Mapping of Artificial Neural Networks Prediction of Surface Finish and Optimization of Machining Parameters in Turning Regarding the Optimization of Measurement Systems for Grinding Forces in Case of High Speed Industrial Robots Solving Load Phase Balancing Problem in LV Distribution Networks by Chaotic Simulated Annealing Study on Anti-Galloping Mechanism and Experimental Effect of the Rotary Clamp Spacer Study on Influence of Paper Fillers on Ink Transfer Study on Processing Properties of Epoxy Resin System in VARI System to Surface Control in Robot Machining The Influence of Circulation Quenching on Temper Brittleness of Steel EA4T The Influence of Paper Brightness on Color Reproduction of Printed Matter Chapter 9: Nanomaterials and Nanomanufacturing Annealing Effect on Synthesis of VO2 (M) Nanopowders by a Novel Solution-Based Process Effect of Fluorine Content on the Electrochemical Properties of PVDF-Derived Carbons for Lithium Ion Battery Effect of Poly(vinyl alcohol)/Chitosan Ratio on Electrospun-Nanofiber Morphologies Fabrication of Nanomaterial Devices for Field Emission Applications Hydrogen Generation from CDS Modified-Titania Nanotube Arrays Nanomechanical Properties of Vimentin Intermediate Filament Preparation and Performance of 100Ah Li-Ion Battery with LiFePO4 as Cathode Material Preparation of Cr2O3 Nanoparticles via Hydrothermal Reduction of CH3OH Research on Metallic Silicon Used as Lithium Ion Battery Anode Material Research Progress on Preparation Methods of PMIA Fiber Research Progress on Ultraviolet Resistance Performance of PMIA Fiber Sodium Nitrate Assisted Hydrothermal Synthesis of Na0.5Bi0.5TiO3 Nanoflakes Synthesis of Barium Titanate Nanoparticles from Decomposition of Barium Titanyl Oxalate Tetrahydrate with Aid of Supercritical Water Synthesis of Self-Aligned Titanium Oxide Nanotube Arrays in Ammonium Fluoride-Ethylene Glycol Electrolytes with Different Water Contents The Effects of Heteroatom-Doping in Stone-Wales Defects on the Electronic Properties of Graphene Nanoribbons The Mean Projected Range and Range Straggling of Er Ions Implanted in 6h Silicon Carbide TiO2 Nanowires/Nanobelts Originating from Anodically Grown Nanotube Arrays Chapter 10: Biomedical Manufacturing A Theoretical Framework for Healthcare Innovation Management Using Wiki Based Digital Ecosystem An Application of Finite Element Modeling to Pneumatic Artificial Muscle from FESTO Application of Lignin from Oil Palm Biomass as a Fluid Lost Reducer Assisted Research and Optimization of the Proper Neural Network Solving the Inverse Kinematics Problem Bioconjugates Containing Ferritin and Metal Nanoparticles Effect of HF Concentration on Corrosion Resistance of Biomedical Implants Effect of Zr Addition on Mechanical Properties of Ti-Nb-Zr Alloys for Biomedical Applications Effects of Different Neutralizing Agents on D-(-)-Lactic Acid Fermentation by Escherichia coli W Efficiency Improvement of Three-Junction Photovoltaic Cell Based on Gallium-Phosphide-Oxide, Indium-Gallium-Arsenide and Indium-Gallium-Antimonide Functional Properties of Ultrasonically Treated Wheat Gluten Improvement the Cooperation Feature in Distributed Healthcare Information Systems Based on the Fractal Approach: An Empirical Study Laboratory Study on a Novel Self-Diverting Gel Acid System Thickener Prehensile and Stepping Mchanisms for Rbots, Based on Bomechanisms Preparation of Precursor of Lini0.5mn1.5o4 with High Density Review State of Biomass Energy in Iran Static Balancing of Mechanical Systems Used in Medical Engineering Field - Continuous Balancing Synergistic Effect of Lysozyme and Vitamin B1 on the Corrosion Inhibition of Carbon Steel in Sulphuric Acid The Application of Learning Impedance Control to Exoskeleton Arm The Effect of Denser Material than Air in Front of Clinical Radiotherapy X-Ray Beam Ultrasonic Ion Pumps in Bio-Battery's Electrolyte Chapter 11: Environmentally Sustainable Manufacturing Processes and Systems A Hybrid TS-SVM Model for Evaluation of Lake Eutrophication A New PSO-RBF Model for Groundwater Quality Assessment A Virtual Geographic Environment for Simulation Analysis of Dam-Break Flood Routing Design and Anaysis of Thermoacoustic Air Conditioning System as Environmental Friendly Device Evaluation of State Equations of Natural Gas in Pipeline Transportation Future of Wind Energy in Iran Global Structure Analysis of a Class of Power System with Zero Characteristic Root Investigation of Radon in Campus Air Marine Environment Problems Caused by the Development of the Coastal Cities and the Solutions for them New Technologies of Energy Saving and Low CO2 Emission for Iron Making Optimization Design for Production Logistics System of Corrugated Box Photocatalyst TiO2 Supported on Bentonite for Water Organic Pollutants Purification: A Literature Review Research on the Influence of Solar Radiation, Sky Background Radiation and Sea Surface Emission to Infrared Search Review of Renewable Energy in Iran Review State of Geothermal Energy in Iran Solar Home System: A Feasible Solution to the Energy Crisis in Bangladesh Chapter 12: Manufacturing Process Planning and Scheduling A New Type of Walking Robot Based upon Jansen Mechanism Considerations on Decisions Making Process under the Risk of Terrorism Dynamic Optimization of a Plane Manipulator Optimization of the Neural Network by Using the LabVIEW Instrumentation Proportional Pneumatic Distributor Structure and Kinematics of Mechanisms for Position and Control from Farming Machine The Empirical Research of Energy Utilization Efficiency in Industrial Sectors Based on DEA-Malmquist The Role of Information Sharing and Joint Transportation Process for Empty Run Reduction Using an Object-Oriented Approach for Scalable Flexibility in Manufacturing Chapter 13: Meso/Micro Manufacturing Equipment and Processes Impact of 3D Seismic Technologies on Sedimentology Study Prediction of Rupture in Gas Forming Process Using Continuum Damage Mechanic Study of Sol-Gel Auto-Combustion Method Prepare Ni0.6-xZn0.4MgxFe2O4 Study on the Microstructures and Properties of the Lead-Free Easy-Cutting Bial-Brass Chapter 14: Modeling, Analysis and Simulation of Manufacturing Processes A Model for Predicting Flowing Gas Temperature and Pressure Profiles in Buried Pipeline A Survey on the Evolution of Nonconventional Pneumatic Actuators A Web-Lab Environment for the Study of the Job Shop Problem Algorithm for Selection of Simulation Software An Analysis Method of the Electro-Hydraulic Rotational Module An Approach for Simulation Design of Mechanical Assembled Units Analysis & Modelling Options of Elastic Actuators for New Robotics Uses Assisted Research of the Dynamic Neural Networks with Time-Delays and Recurrent Links Assisted Research of the Neural Network Computers Modeling and Simulation Facility Layout of Manufacturing System and Design of Optimization Model Increasing the Operating Safety of the Machine-Tools by Using Hydro-Pneumatic Accumulators. Modeling - Simulation Modeling and Simulation of A 6 Dof Robot Modelling and Experimentation of Solid Lubrification with Powder MoS2 through Self-Repairing and Self-Replenishing Multimode Vibrations Suppression Compensators Design Using Specified Dynamic Performance Reference Models Optimal Design of the Mechanical Systems Using Parametric Technique & MBS (Multi-Body Systems) Software Optimization by Simulation of Fabrication in Manufacturing Robotized Systems Optimization of the Hydraulic Bellows Engine Parameters Used to Drive Irrigation Reel Hose Machine - IATF 300 Providing a Pattern to Evalute CRM Systems Based on EFQM Model in SMEs Real-Time Gesture Recognition for Controlling a Virtual Hand Research of the Neural Network by Back Propagation Algorithm Research on the Application of Virtual Reality Technology on Industry Automatic Simulation Risk Priority Analysis for Engine Based on Fuzzy Weighted Geometric Mean Software Module for Objects Shape Tracing and Recognition before Gripping Substructure-Joint Based Approach to Damped FE Model Updating of Complex Assembly Structure The Application of the Minimum Cut Sets in Reliability Evaluation of Power Transmission and Transformation System The Model of Wax Precipitation and Experimental Validation Using the Web by Finnish SME's for Corporate Social Responsibility Activities Chapter 15: Computer-Aided Design, Manufacturing and Engineering Aspects of Lag's 5-Dof a Biped Robot Stabilization Aspects Regarding the Disc Brake's Thermal Stress Simulation by Using Infrared Thermography CAD Optimal Design, Documentation and Automated Assembly of Mechanical Product CAD-Geometrical Modeling of a Hydro Mechanical Product Comparative Analysis of ZMP for Biped Robot and Human Plantar Pressure Design and Modeling of a Ball Wheel Mobile Robot Design of Digital Controllers for Permanent Magnet Torque Motors Design of Humanoid's Lower Limb Model for Walking Design of Power Quality Monitoring System Designing Arms and Hands for the Humanoid Robot ROMAN Distributed Task Allocation in Multi-Robot Systems Using Argumentation-Based Negotiation Dynamic Analysis of a Mobile Mechanical System with Deformable Elements Effect of Intermediate Location and Time-Varying End Mass on the Dynamic Response of a Flexible Robot Manipulator in Tracing Multi-Straight-Line Path GA Based Trajectory Generation for a 7-DOF Biped Robot by Considering Feet Rotation during Double Support Phase Hardware-Software Co-Design for BLDC Motor Speed Controller Design Mathematical Modeling of Management Decision Activities with Maximum Risk in the Intelligent Robotic Systems Measurements Methods of Industrial Robots Accuracy and Workspace Determination Mechanical Design and Control Issues of a Dexterous Robotic Hand Mechanical Loading of R-R-T Dyade On Improving the Performances of Hydraulic Incremental Positioning Units with Mechanical Position Feedback Optimum Design of Multi-Links Finger Grippers Probabilistic Finite Element Prediction of the Active Lower Limb Model Problems of Loading Capacity of Suction Cups in the Radial Direction Researches Regarding the Use of Elctrohydraulic Servosystems at Industrial Robots Stealth Target Location Algorithm for Low Altitude Based on Microwave Radiometer Study upon the Dynamic Answer of Plane Manipulators The Design and Implementation of Integrated Backup System for EMS Base on the Cloud Computing Technology The Dynamic Behavior of the Elevation Movement Mechanism of One Transfer Manipulator with Electro-Hydraulic Acting The Use of Sensors in a Working Area of a Mobile Robot Towards the Development of Internet of Things Oriented Robot to Object Interaction Framework Chapter 16: Semiconductor Materials Manufacturing Design and Implementation of Embedded Wireless Smart Gateway Based on PXA270 Efficient Heat Dissipation Design of High-Power Multi-Chip Cob Package Led Modules Methods to Improve Properties of Gate Dielectrics in Metal-Oxide-Semiconductor Photoacoustic Imaging Based on Limited-Aperture of Transducer Simulation and Experimental Study of FRD Snubber Circuits in Buck Converter Study on the Technology of MPLS in Wide Area Protection System Chapter 17: Laser Based Manufacturing Effect of 7050 Aluminium Alloy Microstructure on Residual Stress by Laser Shock Processing Inkjet Printing of UV Curable Character Ink and Control of the Dried Droplets Size Investigation of the Scanning Angle and the Orientation of the Absorber Effects on the Photoacoustic Tomography Imaging MMA-Grafted PE Separators of Lithium-Ion Battery Prepared by UV-Radiated Grafting Multiband Techniques of LED and UV Materials on Visualization of Needle Marks Structural Variation of Transition Metal - Fullerene Thin Films Modified by Thermal Annealing and Ion or Laser Beam Bombardment The Analysis of Wave Form for 3-D Wave Tank The Computer Calibration Modeling of Radial Distortion Based Weld System with Parallel Planes Chapter 18: Precision Molding Processes Brazing of Aluminum Tubes Using Induction Heating Macroporous Silicon Fabricated by HF Electrochemical Etching for Antireflective Application in Solar Cells Preparation of Pure Anatase TiO2 Thin Films by DC Sputtering Technique: Study on the Effect of Oxygen Partial Pressure Chapter 19: Nontraditional Manufacturing A Pilot Study of Readers of Freely Charged Newspaper Weighting of Goods by Means of DC Motor Chapter 20: Nanofabrication, Nanometrology and Applications A Density Functional Theory Study on the Ultra Long Single Walled Armchair (3, 3) (Bn)Xcy Nanotubes Application of Adaptive RBF-SMC for Electro-Hydraulic Position Servo System Effects of Adding Multiwalled Carbon Nanotube into Dielectric when EDMing Titanium Alloy Enhancement of TiO2 Thin Film UV Detectors by Study of Electromagnetic Effects of Silver Nanoparticle Gearbox with Worm Face Gear Coated with Nanostructured Multilayer Investigation of Plasmon Resonances of Ag Nanoshells for Sensing Applications Mechanisms of 1D Crystal Growth in Chemical Vapor Deposition: ZnO Nanowires Microwave Sintering of Barium Ferrite Nanoparticles Processed via Sol-Gel Method Preparation of Nanosized Molecularly Imprinted Polymer Spheres for Atrazine Reducing Microbially-Influenced Corrosion on Aluminum by Using Organosiloxane Sol Film with Silver Nanocrystals Study of Polarization and Relaxation on Pb(Zr,Ti)O3 Thin Films by Scanning Probe Microscopy Studying of B, N, S, Si and P Doped (5, 5) Carbon Nanotubes by the Density Functional Theory Synthesis of Anatase-Based Titania Nanostructures Using Extreme Hydrothermal Conditions Synthesis of Na0.5Bi0.5TiO3 Microcubes via a Cr3+-Assisted Hydrothermal Route Hydrothermal Synthesis of CeO2 Nanocrystals Using Oleate-Modified Precipitation Method Chapter 21: Metrology and Measurement Application of the Measurement and Control Network on Rewinder Automatised Line Used for the Assembly/Test Subsystem-Carcass Experimental Setup for Harmonic Drive Efficiency Determination Nondestructive Evaluation of Material Damage Using Nonlinear Rayleigh Waves Approach Stability Analysis of an Aeroelastic System with Actuator Saturation Study on the Safety Assessment of the Mobile Scaffolding System Metal Structure Based on the Onsite Inspection Temperature Determination of St-Al Joints during Friction Welding Wrist Mounted Camera for Colour and Shape Recognition Chapter 22: Mechanical and Electronic Engineering Control A New Approach to Popov Criterion for Stability Analysis of Nonlinear Control Systems Antropomorphe Robot with 4 Degrees of Freedom for Didactic Use Application and Research on the Model of Saturated-Unsaturated Porous Material Coupling Hydro-Thermal-Mechanical Process Applications of the Flexible Wing Concept at Small Unmanned Aerial Vehicles Bending-Torsional Flutter of a Composite Rectangular Cantilever Wing Subjected to Engine Thrust Classification of Power Quality Problems by Wavelet Fuzzy Expert System Contribution to Stability Control of Nonlinear Systems Design Consideration of Bio-Inspired Contractible Water-Jet Propulsor for Mini Autonomous Underwater Robot Designing the Tracking System for a String of Photovoltaic Modules Electronic Interface for Pneumatic Grippers Using USB Port Failure Process and Mechanism Analysis for the Connecting Rod of Diesel Engine Finite Element Analysis and Design Exploration of a Bolted Joint Fluctuation-Suppression Pitch Control Strategy Study for Wind Turbine Fuzzy Thrust Staging Kinematics for the NERVA Strap-On Boosters Global Fast Terminal Sliding Mode Control for Wind Energy Conversion System Hydraulic Positioning Unit with Internal Mechanical Position Feedback Identification of Tight Spots to an Automatic Mechanical Assembly Line, by Simulation WINQSB Implementation of RFID-Based Access Control Management System Indoor Navigation and Guidance of an Autonomous Robot Vehicle by Using Wireless (ZigBee) Cummunication Logic Design of Improved Backup Power Automatic Switching Considering the Influence of Small Hydropower Stations Manufacturing Using Robot New Inverter Fault Current Limiting Method by Considering Microgrid Control Strategy Off-Line Programming of Industrial Robots Using Co-Located Environments Performances Evaluation for a Reversed Quasi-Carnot Cycle (Refrigeration Machine) by Using the Direct Method from Finite Speed Thermodynamics PID Parameters Tuning Based on Wavelet Neural Network for Automatic Voltage Regulator Control System Research on Engineering Machinery Manufacturing PDM and CAD Integration Solutions Research on the Vacuum Attachment System of a Cleaning Robot with Vertical Displacement Researches on a New Type of Rotating Thermic Motor Robot - Turner Spatial Information System for Management and Control of Electrical Substations Technical Options for Off-Grid Electricity Supply The Design and Implementation of Intelligent Community Monitoring System The Dynamic and Lightweight Design of the Support Structure of Electric Vehicle's Power System The View to the Current State of Robotics Torque Control and Pitch Control Strategy in VSCF Wind Turbine above Rated Wind Speed Using the Microcontroller and the PLC in a RPP Robot Control Vibration Diagnosis of Electric Motor's Bearings Voltage Stability Enhancement Considering Operation of Smart Loads

「Nielsen BookData」 より

詳細情報

• NII書誌ID(NCID): BB09097148
• ISBN:
  • 9783037853634
• 出版国コード: sz
• タイトル言語コード: eng
• 本文言語コード: eng
• 出版地: Durnten-Zurich
• ページ数/冊数: 2 v.
• 大きさ: 25 cm
• 親書誌ID:
  • BA24926058