Measurement and control of granular materials : selected, peer reviewed papers from the 9th International Conference on Measurement and Control of Granular Materials, MCGM 2011 (Global High Level Academic Seminar) Shanghai, China, 27-29 October, 2011
著者
書誌事項
Measurement and control of granular materials : selected, peer reviewed papers from the 9th International Conference on Measurement and Control of Granular Materials, MCGM 2011 (Global High Level Academic Seminar) Shanghai, China, 27-29 October, 2011
（Advanced materials research, v. 508）
Trans Tech Publications, c2012
- : pbk.
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
These are the proceedings of the 9th International Conference on Measurement and Control of Granular Materials (MCGM' 2011), held on the 27 to 29th October, 2011, in Shanghai, China. The 63 peer-reviewed papers are grouped into the chapters: 1: Flow Measurement and Pneumatic Conveying; 2: Measurement of Size, Volume and Other Parameters; 3: Tomographic Technology, Image Processing and Related Sensors; 4: Powder Explosion and System Protection; 5: New Instruments and Sensor Development; 6: Nano and Powder Materials Preparation; 7: Materials Processing and Preparation; 8:Powder Materials Measurement and Processing.
Volume is indexed by Thomson Reuters CPCI-S (WoS).
目次
Preface and Organization
Chapter 1: Flow Measurement and Pneumatic Conveying
Test Procedures and Signal Misinterpretation for Electrostatic Gas-Solids Flowmeters
High Speed Visualization of Pneumatic Conveying of Materials in Bypass System
Experimental Investigation of Pressure Drop in Bypass Pneumatic Conveying of Fly Ash
Investigation of Flow Channel Geometry and Draw-Down in Funnel-Flow Bins and Stockpiles
Research of Gas/Solid Two-Phase Flow Capacitance Cross-Correlation Measurement System
Flow Characteristics of Gas-Solid Two-Phase Flow in Annular Pipe of Gas Drilling
Application of Grey Correlation Degree in Identification of Two-Phase Flow Patterns
Chapter 2: Measurement of Size, Volume and other Parameters
Particle Size Analysis by Laser Diffraction Method Using Reference Particles
Characteristics of Dry Ice Particles Produced by Expanding Liquid Carbon Dioxide and its Application for Surface Cleaning
Volume Measurement of Large Material Stack Based on the RBFNN Interpolation
Uncertainty Evaluation in Measure Results of Rock Permeability
Macrograph Grain Size Analysis Method of Tight Gravel-Rock Huang Lina
Measurement on the Shear Property Parameters of the Eruption Powder
Study on Petrophysical Parameters Testing Technology for Loose Rock
Grain Gradation Design for Al2O3-MgO-C Refractories Based on Close Packing Theories
A Combined Interpolation Method for Cross Correlation Based Particle Velocity Measurement
Chapter 3:Tomographic Technology, Image Processing and Related Sensors
A Novel Approach to Multiphase Flow Metering Using PIV and Tracer Dilution
Process Tomographic Measurements of Granular Flow in a Pneumatic Conveying System
Image Reconstruction Based on Compressed Sensing with Split Bregman Algorithm and Fuzzy Bases
Optimum Design of an Internal 8-Electrode Electrical Capacitance Tomography Sensor Array
Research on Human ADL Data Real-Time Transmission Optimization Method Based on Bayesian Network
Optimization Design of Capacitance Sensor with Helical Shaped Surface Plates
An Image Quality Assessment Algorithm for Palm-Dorsa Vein Based on Multi-Feature Fusion
Chapter 4:Powder Explosion and System Protection
Assessing the Explosion Risk of Plants for Dusty, Granular and Combustible Products Example of a Risk Assessment Procedure for a Fluid Bed Spray Granulator
Experiment and Analysis of Large Energy Spark Discharge
Comparison and Analysis of Different Standards for Determining Dust Resistivity
Determination of Kinetic Parameters of Maize Starch in Air Using Thermogravimetric Analysis
Modeling of Magnesium Powders Explosion in a 20L Sphere
A Study on Explosion Characteristics of Toner Powder
New Findings for Explosion Protection of Bucket Elevators by Design Measures
Chapter 5:New Instruments and Sensors Development
The Investigation of Arch Model Acting in Mass-Flow Hoppers
New Instrument PFT for Powder Flow Researching
High-Resolution Ultrasonic Spectroscopy for Crystallization Process
Development of an Embedded High-Temperature Field Measuring Instrument
Segregation Diagram of a Mixture of Particles with Different Sizes and Densities
Deformation Modes for Assemblies of Frictionless Polydisperse Spheres
Design and Application of Virtual Instrument Detection System for Aerodynamic Instrument
Simulation Study of Spiral Electrode Capacitance Sensor for Measuring Concentration of Gas-Solid Two-Phase Flow
Chapter 6:Nano and Powder Materials Preparation
Population Balance Modelling and Experimental Validation for Synthesis of TiO2 Nanoparticles Using Continuous Hydrothermal Process
An Experimental Study on the Characteristics of Nanoparticles Emission from a Vehicle
Preparation of Super-Fine Cerium Oxide Using Mechanically Chemical Method
Preparation of Nano-Sized TiO2 Supported on Granular Activated Carbon and the Photocatalytic Degradation of Methylene Blue
A Study on Grinding Rate of Mica Particles
Environmental Risk and Recoverable Potential Evaluation of Heavy Metals in the Sludge from the Industrial Wastewater in China
Modification of Sepiolite and its Ability to Remove Heavy Metals
Operation Efficiency Evaluation on Small and Medium-Sized Powder Metallurgy Enterprise Cluster Supply Chain
Chapter 7:Materials Processing and Preparation
Control and Characterization of Materials Recovered from Mechanical Recycling of Waste Refrigerators
Investigation into Hydrolysis of Alkaline Sodium Borohydride Solution Using Attapulgite Clay-Supported Co-B-Ce Catalyst
Design of Supervisory Control and Data Acquisition (SCADA) Platform for TE Process
Direct Synthesis and Characterization of Ti-SBA-15 with Different Ti Precursors
Influence of Operating Parameters on Photocatalytic Degradation of Methylene Blue in UV/ Tb3+ and Sm3+ Co-Doped TiO2 Process
Microbial Leaching of Copper from Waste Electronic Scraps
Prediction on Molten Steel End Temperature during Tapping in BOF Based on LS-SVM and PSO
Controllable Imprinted Polymer Layer Coated Silica-Gel for S-1-(1-Naphthyl) Ethylamine Recognition by ATRP
Chapter 8:Powder Materials Measurement and Processing
Study on the Pressure-Sinkage Relationship of Lunar Soil Simulant
Growth of Ceramic Coatings on LY12 Aluminum Alloys by Micro-Arc Oxidation and Microstructure Properties of Ceramic Coatings
Scanning Probe Microscope Observation to Morphology of Typical Carbon Materials
Experimental Study on Flow Field Characteristic of Bag Filter
Photocatalytic Activity of Gd3+ and Sm3+ Co-Doped BiVO4 Powders Prepared by Chemical Precipitation Process
Velocity Measurement for Flow Particles by Using Spatial Filtering Technique Based on Sensor Array
Effects of Quenching Heat Preserving Time on Structure and Properties of Boron-Containing High-Cr White Cast Iron
Research of Corner Detection Algorithm with Stack Volume Measurement
Modified Board System for Ecological Monitoring of Ground-Based Objects State
「Nielsen BookData」 より
