Tribology in manufacturing technology
著者
書誌事項
Tribology in manufacturing technology
(Materials forming, machining and tribology / J. Paulo Davim, series editor)
Springer, c2012
大学図書館所蔵 全4件
  青森
  岩手
  宮城
  秋田
  山形
  福島
  茨城
  栃木
  群馬
  埼玉
  千葉
  東京
  神奈川
  新潟
  富山
  石川
  福井
  山梨
  長野
  岐阜
  静岡
  愛知
  三重
  滋賀
  京都
  大阪
  兵庫
  奈良
  和歌山
  鳥取
  島根
  岡山
  広島
  山口
  徳島
  香川
  愛媛
  高知
  福岡
  佐賀
  長崎
  熊本
  大分
  宮崎
  鹿児島
  沖縄
  韓国
  中国
  タイ
  イギリス
  ドイツ
  スイス
  フランス
  ベルギー
  オランダ
  スウェーデン
  ノルウェー
  アメリカ
内容説明・目次
内容説明
This book aims to show how tribological concepts can be applied in order to improve manufacturing technology in modern industry. It can be used as a guide book for engineering students or a reference useful for academics in the fields of tribology, manufacturing, materials and mechanical engineering.
目次
Preface
1 Tribology of cutting tools
1.1 What is the tribology of cutting tools?
1.1.1 Tribology of metal cutting
1.1.2 Tribology of cutting tools
1.1.3 Importance of the subject
1.1.4 Why now?
1.2 Underlying principle
1.3 Tribological interfaces: tool-chip interface
1.3.1 Geometry of tool-chip interface
1.3.2 Summary of tribological conditions at the tool chip interface
1.3.3 System consideration
1.3.4 Stress distribution and mean
1.3.5 Temperature
1.3.5.1 Known facts
1.3.5.2 Contradiction
1.3.5.3 Moving chip - the governing equation
1.3.5.4 Summary of temperature consideration
1.3.5.5 Optimal cutting temperature law
1.3.6 Issues to be addressed
1.3.6.1 FEM modeling of contact stress distributions
1.3.6.2 Particularities of stress distribution on the restricted tool-chip contact lenght
1.3.6.3 Influence of cutting speed
1.4 Tribological interfaces: tool-workpiece interface
1.5 Tool wear
1.6 Improvements of tribological conditions of cutting tools
1.6.1 Grades of tool materials
1.6.1.1 Basic properties of tool materials
1.6.1.2 Selection of application specific grade of HSS
1.6.2 Application of the metal working fluid (MWF) through the cutting tool
References
2 Tribology of machining
2.1 Friction interactions in machining
2.2 Cutting, ploughing and sliding interactions (after Jackson and Morrel, 2011)
2.2.1 Static friction and stick-slip phenomena
2.2.2 Sliding friction
2.2.2.1 Models for sliding friction
2.2.3 Friction heating
2.3 Lubrication to control friction in machining (after Jackson and Morrel, 2011)
2.3.1 Liquid lubrification
References
3 Tribology in metal forming processes
3.1 Introduction
3.2 Friction
3.3 Lubrication
3.4 Wear
3.5 Conclusion
References
4 Tribology in hot rolling steel strip
4.1 Introduction
4.2 Structure of oxide scale and oxidation kinetics in pure iron and carbon steel 4.2.1 Pure iron
4.2.2 Carbon steel
4.2.2.1 800 DegreesC and above
4.2.2.2 Below 800 DegreesC
4.2.3 Structure of oxide scale and oxidation kinetics in stainless steels
4.2.4 Oxidation of stainless steels in moist atmosphere
4.2.5 Oxidation of stainless steels in hot strip rolling
4.3 Mechanical properties and thermal properties of oxide scale
4.3.1 Surface characteristics
4.3.2 Morphology on cross section
4.4 Mechanical properties and thermal properties of the oxide scale
4.4.1 Mechanical properties and measurement methodology
4.4.2 Thermal properties and the effect of oxide scale on heat transfer
4.5 Evolution of oxide scale during hot rolling
4.5.1 Oxide scale growth and deformation during finishing rolling
4.5.2 Oxide scale structures developed on hot rolled steel strip
4.5.3 Deformation and fracture behaviour of oxide scale under hot rolling conditions
4.5.3.1 Carbon steel
4.5.3.2 Stainless steels
4.6 Oxide scale involved surface roughness and its transfer during hot rolling
4.6.1 Carbon steel
4.6.2 Stainless steels
4.6.3 Numerical simulation
4.7 Evaluation of friction in hot rolling and tribological effect of oxide scale
4.7.1 Evaluation of friction in hot rolling
4.7.2 Tribological effect of oxide scale
4.7.2.1 Carbon steel
4.7.2.2 Stainless steels
References
5 Micro-contact at interface between tool and workpiece in metal forming
5.1 Introduction
5.2 Micro-contact under each lubrication
5.2.1 Micro-contact under dry and thin film lubrication
5.2.2 Micro-contact under thick film lubrication
5.2.3 Micro-contact under micro-plasto-hydrodynamic lubrication
5.2.4 Micro-contact under mixed lubrication
5.3 Micro-contact at the interface between tool and workpiece in sheet metal forming
5.3.1 Direct observation of micro-contact.
5.3.2 Lubrication mechanism at interface between tool and workpiece
5.4 Micro-contact at interface between roll and sheet in cold sheet rolling
5.4.1 Inlet oil film thickness
5.4.2 Micro-contact at interface between roll and sheet
5.4.3 Estimation system for micro-contact of roled sheet in stainless steel cold rolling process
5.5 Conclusions
References
6 Coatings and applications
6.1 Introduction
6.2 Plasma nitriding
6.3 Chemical vapor deposition
6.4 Physical vapor deposition
6.4.1 Deposition by vacuum evaporation
6.4.2 Cathode sputtering
6.4.3 Ion plating
6.5 Modern coatings
6.5.1 Multilayer
6.5.2 DLC-diamond-like carbon
6.5.2.1 Process of DLC coating manufacture
6.6 Coating properties
References
「Nielsen BookData」 より