Mechatronics and intelligent materials III : selected, peer reviewed papers from the 2013 International Conference on Mechatronics and Intelligent Materials (MIM 2013), May 18-19, 2012 [sic], XiShuangBanNa, China
著者
書誌事項
Mechatronics and intelligent materials III : selected, peer reviewed papers from the 2013 International Conference on Mechatronics and Intelligent Materials (MIM 2013), May 18-19, 2012 [sic], XiShuangBanNa, China
（Advanced materials research, v. 706-708）
Trans Tech Publications, c2013
- : [set]
- Part 1
- Part 2
- Part 3
大学図書館所蔵 件 / 全1件
-
Part 1A25118/706-1400060045,
Part 2A25118/706-2400060053, Part 3A25118/706-3400060061 -
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
"... The 3rd International Conference on Mechatronics and Intelligent Materials 2013 (MIM2013), will be held in XiShuangBanNa, China during May 18-19, 2013."--pref.
内容説明・目次
内容説明
Volume is indexed by Thomson Reuters CPCI-S (WoS).
Collection of Selected, peer reviewed papers from the 2013 International Conference on Mechatronics and Intelligent Materials (MIM 2013), May 18-19, 2013, XiShuangBanNa, China.
The 466 papers are grouped as follows:
Chapter 1: Materials Engineering and Technologies of Processing;
Chapter 2: Construction and Environmental Engineering;
Chapter 3: Mechatronics, Control and Automation, Measurement and Measuring Equipment;
Chapter 4: Mechanical Engineering and Manufacturing;
Chapter 5: Data Processing, Computer and Information Technologies;
Chapter 6: Engineering Management and Product Design.
目次
Preface and Committee
Chapter 1: Materials Engineering and Technologies of Processing
Analysis of the Wedge Tip Fillet for Central Defeats in the Process of Cross Wedge Rolling 4Cr9Si2 Valve
Application of Materials Studio Modeling in Crystal Structure
Applied Research of Intelligent Textile Fiber Materials
Catalytic Activity of Tetranitro-Copper Phthalocyanine Supported on Carbon Nanotubes towards Oxygen Reduction Reaction
Characteristics Analysis of Plane Processing of Sapphire Corundum Crystals
Characterization of Antioxidant Chitosan Film Incorporated with Pomegranate Peel Extract
Characterization of Poly(Diethylene Glycol Adipate -co- Neopentylglycol Adipate) as a New Plasticizer for Poly(Lactic Acid)
Characterization of Tri-(1, 4-Butanediol Single-Butyrate) Citrate as a New Plasticizer for Poly(Lactic Acid)
Chiral Separation of Amlodipine and its Enantiomer on a Molecularly Imprinted Polymer-Based Stationary Phase
Chiral Separation of R,S 3-(4-Fluorophenyl) -2,2-Dimethylcyclopane Carboxamide with Monolithic Molecularly Imprinted Polymers
Comparison on Antimicrobial Activity of Different Solvent Extracts from Aerial Stem and Rhizome of Douttuynia cordata
Copolymer Based on Bromobenzene and 3,4-Ethylenedioxythiophene
Design, Materials and Processing for the Summer Olympic Torches
Determination of Bond Lengths and Electronic Structure of Cd1-xZnxTe Ternary Alloys by Synchrotron Radiation
Determination of the Impurity Element Gallium in the Metallic Aluminum Products such as Aluminum and Aluminum Alloy by ICP-OES
Dielectric Properties and Microstrip Patch Antenna Performances of 0.95MgTiO3-0.05CaTiO3 Microwave Ceramics
Effect of Chlorogenic Acid on H2O2-Induced Dysfunction and Apoptosis in HUVECs
Effect of Different Content of AlF3 of the Zinc Flux and Temperature on the Spreading Performance of Zn20Sn
Effect of Equal Channel Angular Pressing and Annealing on Corrosion Resistance of Cu-Zn Alloy
Effect of Annealing Temperature on Resistance Switching Behavior of Bi4Ti3O12 Thin Films Deposited on ITO Glass
Effect of Carbon Doped in BN on Thermodynamic Properties
Effects of Load on the Wear Behaviors of Cu-Based Composite under Different Electrical Currents
Effects of the Mould Pressure and Mould Pressing Time on the Properties of Graphite/Phenolic Resin Composites
Elastic Properties of Rhombus Dodecahedron Open-Cell Cellular Materials
Electric Fatigue in Metal/Ferroelectric Polymer/SiO2/p-Si Capacitors
Experimental Research of New Rotor with Variable Clearance in Mixing the Short Fiber-Rubber Composite
Experimental Study for Biogas Upgrading by Water Scrubbing with Adsorption Materials Used for Scrubber Packing
Fabrication of Bioceramic Scaffolds for Tissue Engineering Using Additive Manufacturing Technology
Fabrication of Porous TiO2 Electrodes from P25 Powder by Chemical Technique for Dye-Sensitized Solar Cells
Gas Response Properties of Noble Metal Modified TiO2 Gas Sensor
Hydrogen Properties of Lithium Doped Stannic Oxide Thick Film Sensors
Influence of the Temperature on Ultimate Strength of 93WNiFe Alloy
Interfacial Reactions between Sn-Ag-Cu-Fe Composite Solder and Cu Substrate
Material Removal Property in Low Energy Ion Beam Etching
Modeling of Phase Transformation for TA15 Titanium Alloy During Heat Treatment
Multiscale Parameter Identification Method for Three Dimension Steady Heat Transfer Model of Composite Materials
Nd:YAG Laser Welding between Ti and PET Using Pulse Shaping
Optimization and Application of Secondary Cooling on 37Mn5 Steel o210mm Round Billet
Optimization Decomposition Cast Structure in M35 High-Speed Steel
Optimizations of ZnO/Si(100) with ZnO/ZnMgO Super Lattice Buffer Layers Grown by Molecular Beam Epitaxy
Organized Assembly and Morphologies of Aromatic Schiff Base Compounds in Organized Molecular Films
Oxidition Resistance of Multi-Arc Ion Plating TiN Films
Parameters Study for Composites Forming Infusion from inside and outside at Same Time
Performance of Self-Lubricant Bearing from Composite Material and its Application Practice in Textiles
Phase Diagram and Research for the Ternary System of NaCl-CsCl-H2O at 50 DegreesC
Physical Properties and Antibacterial Activity of a Chitosan Film Incorporated with Lavender Essential Oil
Prediction of Soluble Solids Content of Jujube Fruit Using Hyperspectral Reflectance Imaging
Preparation and Luminescence Properties of Rare Earth Magnesium Strontium Silicate Luminescent Fiber
Preparation and Microstructure of Two Kinds of Exfoliated Graphite
Preparation and Structure Characterization of Poly(lactide-co-ethylene carbonate) Microspheres
Preparation of Core-Shell Silica - 12-Tungstophosphoricacid Nanoparticles for Acylation of Aromatics
Preparation of TEM Specimens from Gas-Atomized Fe-6.5wt.%Si Powders with Several Micrometers Using Focused Ion Beam
Preparation ZnS Quantum Dots via Water-Phase Synthesis Method
Press Forging Forming of Stepped Holes in Thick Sheet Metal
Research of Cr1-xMxN's (M=Al,V,Ti,etc.,x=0.5) Coating Valence Electron Structure Calculation and Wear-Resisting Performance
Research on Interfacial Assembly of Some Trigonal Schiff Base Amphiphiles in LB Films
Researches on the Formation and Thermal Treatment of (Zn0.3Co0.7)2-W Type Ferrite
Rheology Properties of Ni/TiO2/SDBS EMR Fluids
Simulation and Optimization of Steel Casting by Sand Casting
Strain-Rate Characteristic of the Brush Plated Nanocrystalline Cu
Study on Aging Resistance Properties of Natural Rubber Dried by Microwave
Study on Atmospheric Pressure Plasma Processing of Fused Silica
Study on Electromagnetic Properties of Ni-MWNTs Filling High Dielectrical EP Composites
Study on Preparation and Tribology Behaviors of Ni-P Electroless Deposited Nanocrystalline Coating
Study on the Interaction between a Self-Assembling Peptide and Paclitaxe
Study on the Properties of Functional Cleancool Fiber
Study on the Yield-Thixotropy of Waxy Crude Oil under Uniform Sweeping Rate of Share Rate
Studying on Hot Pressure Casting Process of CaZr0.9In0.1O3- Tubes for Hydrogen Sensor in Aluminum Melt
Studying Status and Application Prospect of Cryogenic Treatment on HSS
Synthesis and Characteristics of Poly(ethylene terephthalate)/SiO2/TiO2 Hybrid Composites by Sol-Gel Method
T-BN Powders Prepared by Chemical Vapor Deposition Using BCl3, NH3 and Ar
The Bioactivity of Gradient Composite Bioceramic Coating with Different Contents of Multiple Rare Earth Deoxide Fabricated by Wide Band Laser Cladding
The Color, Taste and Toxicity of Non-Ferrous Metals
The Coming of Quasicrystal: Discovery, Principle and Application
The Effect of SiC Content on the Microstructure and Thermal Conductivity Properties of SiCp/Cu Composites
The Influence of Poly Lactic Acid's Crystalline Behavior and the Compatibility by Poly(Ionic Liquid)
The Mechanical Properties and Hydrophilicity of Poly(L-Lactide)/Laponite Composite Film
The Micro-Structure and Wear Behavior of the SiCp/Cu Composites before and after Chemical Plating
The Patented Project Design for Preparing SnSe2 Nanosheets
The Preparation of Lithium Ion Sieve and Determination of its Adsorption Performance Parameters
The Programming Strategie of High Speed Milling on Aluminum Ally Bowl-Shaped and Thin-Walled Part by Using Powermill Software
The Structures and Features of Atomic Defects in Fe-Al Alloys
The Study and Application on Injection Mold Design of Side Holes Plastic Parts
The Temperature Field Test and Numerical Simulation of Steel's Friction Stir Welding Process
Tribological Properties of PVD CrAlN Coating Tools
Electrical Transport Properties in Ta-Doped SnO2 Thin Films
Application of New Ecological Clothing Materials in Green Design for Dressing
An Effective MECE Module as a Recycling Process for PET Diaphragm of Digital Paper
Applying and Practicing of MATLAB Programing for Voronoi Tessellation
Energy Level Width of 2DEG in Different Well in Mesoscopic System
Identification of Volatile Compounds in Cooked Meat of Farmed Obscure Puffer (Takifugu obscurus) Using SDE and HS-SPME Combined with GC-MS
A New Synthesis Method of Nanomaterial Using Diisopropylamine
Mathematics Model of the Question of Micro-Pits Image with Direction-Uniformity Distribution and Area Scrambling Micro-Pits Image Design Methods Based on Regular Graphics Arrangement
The Micro-Pits Image Design Method with Direction-Uniformity Distribution Based on Minimum Interval Area Scrambling
The Practice and Cognition of Hydraulic Fracturing Technique for Shale Gas Reservoir in Southeast Chongqing
The Principle and Applications of Colored Solar Cells
An Experimental Study on the Clearance Design of Fine Blanking Tool for High-Strength Steel Special Parts with Various Inner Corner Shapes
An Optimized Method for Choosing Friction Stir Welding Parameters
Analysis Drive Index of A12 Oil Reservoir
Analysis of Biological Dirt on the Sewage-Source Heat Pump Exchange Surface
Numerical Simulation Optimization Research of Cold Extrusion Forming for Injection Head
Press Forging Forming of the Round-Fin on Heat Sink
Research and Application of Warm Extrusion Forming Technology for Internal Combustion Engine Piston Head
Study on the Drying Mechanism and Dynamics of Palygorskite
The Microscopic Study on the Basis of Finite Element Johnson-Cook Model to Powder Compacting Mechanism
Chapter 2: Construction and Environmental Engineering
A Comparative Research on Sludge Properties under Different Wastewater Quality Conditions
Comparative Study on Nonlinear Earthquake Response of Girder Isolated Bridges with LRB and Model Shaking Table Test
Comparison of Antimony Determination Methods in Drinking Water
Comprehensive Prediction about Water Abundance of NO.5 Coal Seam Roof' Sand in Yili NO.1 Coal Mine
Design and Simulation Analysis for Power Plant Coal Storage Bunker Girder Structure
Evaluation of Coal Floor Water Inrush Risk with Five-Figure and Double-Coefficient Method
A Technique Method of Recycling Cyanide Zinc Plating Waste Liquid in the Laboratory
A Technique Method of Recycling Waste Liquid in the Sulfate Copper Plating Technological Experiment in the Laboratory
Influence of C and Values on Slope Supporting by Soil Nailing Wall in Thick Miscellaneous Fill Site
Spectacular Display of Light Techniques - The Artistic Expression of Glass Materials in Modern Architecture Space
Study on Long-Term Performance of Concrete Based on Seawater, Sea Sand and Coral Sand
The Application of Glass Materials in Building Design
The Fractal Properties of Scale Effect on the Density of Rock-Fill Materials
Effect of Flow Characteristics of Polymer Flooding Produced Liquid on Attrition of Sucker Rob and Tube
Application of Stress Box in Self-Stressing Test of Expansion Concrete Filled Steel Tube
Experiment on Mechanical Properties of Steel Fiber Concrete under Dynamic Load
Experimental Study of Self-Stressing and Static Load on Self-Compacting Concrete Filled Steel Tubular
Isolation and Identification of a Cellulolytic Bacterium from the Huguang Maar Lake
Investigation of Entropy and Gray Theory in Coal and Gas Outburst Controlled Factors Assessment
Research on Interval Reversible Inverse Analysis Method Based on Interval Parameters
Stability Analysis about the Impact of Soft Rock to the Underground Cavern Group
Study on the Flow Field of Air Floating Pool of Pressurized Dissolved-Air Floatation Water Treatment System
Study on the FRP Tendons in Acid Erosion Test of the Durability
The Current Using Situation of SBS Modified Asphalt in China and a New Method of Monitoring SBS Modifier Dosage
Application of Phast in the Quantitative Evaluation for the Liquefied Ammonia Leakage Accidents
Chapter 3: Mechatronics, Control and Automation, Measurement and Measuring Equipment
H Filtering for Markov Jump Systems with Mixed Modes
A Design of Algorithm for Excimer Laser Coaxial Observation Automatic Tracking Processing System
Edge Detection and Accurate Rectification Technology in the Digital Detection for Dry Cell Substratum Pixel
A HSV Space Shadow Method Based Human Motion Detection
A Intergrated Compensation Device Design for Three-Phase Unbalance and Reactive Power of Low Line
A New Testing System of Missile-Target Encounter Based on Doppler Fuse
A Research on Navigation Star Catalog Selection Algorithm Based on SVM
Accuracy-Complexity Trade-Off for the Signal Reconstruction of Multifunctional Sensors
An Adaptive KLT Algorithm for Hand Gesture Tracking
An Echo-Based Gait Phase Determination Method of Lower Limb Prosthesis
An Energy Aware Routing Based on Swarm Intelligence for Wireless Sensor Networks
Analyze the Transient Response of a Control Systems
Application and Research of Multi-Sensor Data Fusion for the Earlier Period Diagnosis in Induction Motors
Application of Neural Network Based on the Immune Genetic Algorithm in Failure Diagnosis
Application Research of ARM Embedded System in the Vision System of Chip Mounters
Automatic Data Acquisition System in Wheel-Rail Monitoring Test Bench
Based on Block Averaging Pre-Processing Differential Coherent Integration Weak Signal Acquisition Algorithm
Based on the Double SCM Real Time Control System Design of Drum Brake
Biped Walking Robot Gait Planning Research
Blind DOA Estimation Based on Single Acoustic Vector Hydrophone
Cognitive Developmental Grasp Robots: From Infant Development to Computational Modeling
Comparing and Analysis of Schemes of Condition Monitoring for CNC Machine Tool Servo System
Control and Research of Bionic Robotic Fish Based on Arduino
Control Strategy for Space Manipulator Based on Genetic Algorithm Self-Tuning
De-Noising Method of a Certain Missile Homing and Control Signal Based on Wavelet Transform
Design and Research of Carbon Dioxide Automatic Measuring Instrument
Design of a Portable Formaldehyde Meter
Design of an Intelligent Point-to-Point Swing Arm Controller
Design of Electric Control System of Stainless Steel Composite Plate
Design of Fuzzy PID Controller Based on Adaptive Particle Swarm Optimization with Cloud Theory
Design of Intelligent Cleaning Robot Based on Fischertechnik
Design of Lightweight RFID Middleware for Warehouse Management System
Design of Measurement System of the Center of Gravity
Design of PMSM Position Servo System Based on Fuzzy Adaptive PI Control
Design of Temperature Control System for Thermocouple Verification Based on Virtual Instrument Technology
Design of Temperature Monitoring System for Solar Laminator Based on ZigBee Technology
Detection of Silver Jewelry with Orthogonal Double-Pulse LIBS
Developing and Research on Experiment Device Based on STC90C51 SCM
Development and Application of Metering Instrument for Well-Head Metering in Block 75 of Sulige Gas Field
Development and Research of Colony Analysis System Based on Image Processing
Development of Synchronized Biomechanics Sensors Detection Software
Development of the Amplitude-Frequency Characteristic Tester Based on SCM Control
Device Controller Design Based on the Internet of Things
ECG Signal Denoising Algorithm Based on Optimization Wavelet Transform
Evolvement of Research in Impedance-Measuring Device for Structural Health Monitoring
Fast Algorithm with Improved Circular Correlation Method for GPS Signal Acquisition
Fault Diagnosis of Rolling Bearing Based on S Transform and Image of Invariant Moments
Fault Diagnosis System of Rolling Bearing Based on Ultrasonic Signal
Gait Planning and Simulation of the JQRI00 Quadruped Robot
Hardware Design of Microcomputer Relay Protection Device Based on ARM&DSP
High Performance and Full Digitalization Design of Brushless DC Motor Control System
High Performance Drive Design for Hybrid Stepper Motors
Influence of Silicon Controlled Rectifier Voltage Regulation Device under DDC-Temperature Control
Integrative Control of Regenerative Braking System and Anti-Lock Braking System
Integrity Protection of the Intelligent Robot's Remote Information
Localization of Magnetometer Sensor Based on Magnetic Gradient
Magnetic Field Intensity Gradient Method on the Detection of a Remote Target
Mechanical Analysis of Snake-Like Robot for Colonoscopy
Mixed Ant Colony Algorithm for Vehicle Routing Problem with Time Windows
Modeling and Simulation of Circulating Fluidized Bed Boiler Combustion System Based on Neural Network
Multiobjective Topology Optimization of Multi-Input and Multi-Output Compliant Mechanisms with Geometrically Nonlinearity
Multi-Step Ahead Prediction for Electromechanical Device Using Multivariate SVM Predictor
On Study of High Speed Permanent Magnet Synchronous Motor without Iron Core
Optimum Slide-Way Structural Design for a New Polarized Scattering Instrument
Performance Assessment Model for Highway Electromechanical System
Performance Study and Structure Control of Carbon Aerogel
PID Control Strategy of Vehicle Active Suspension Based on Considering Time-Delay and Stability
Progress in Lamb Wave Testing and Research Based on PZT
Remote Control Technology in Intelligent Oil-Well Based on Acoustic Wave
Remote Localization of Underwater Magnetic Target
Research and Application of Weighing Low Temperature and Mobile Metering Device
Research and Exploration of Carbon Dioxide Concentration Real-Time Monitoring System Based on Freescale MCU
Research of Large Excavator Multidimensional Intelligent Vibration Monitoring and Fault Diagnosis System
Research of the Control Method for the Uniformity of Insulation Layer on Communication Cable
Research of the Electronics Definite Direction Technology
Research of Ultrahigh Vehicle Detection System Based on Infrared Sensor
Research on Automatic Packing Machine's Manipulator of Amorphous Silicon
Research on Electronic Differential Control Method of Electric Vehicle with Motorized Wheels Based on Adhesion Coefficient
Research on Fault Analysis and Fault Diagnostics Technology for Large-Size Equipments in Stopes
Research on Method of Coal Shearer States Monitoring
Research on Motion Characteristic Simulation of 8x8 Omnidirectional Platform
Research on Parametric Digital Model Form Based on 3-Dimensional Body Measurement
Research on pH Value for City Sewage Optimized Control Based on HDP
Research on Visualization of Cutting Tools' Wear Measurement of Shield
Research Progress of Solar Auto-Tracking System - Solar Hybrid Tracking Mode
Research of Intelligent Monitoring System of Tower Crane Based on RFID
Self-Identification Method and Application of Measuring Equipment under Conditions of Close Arrange Stations
Sliding Mode Nonlinear Observer Design for Underwater Vehicle Control System
SnO2 Nanofibers Gas Sensor Detecting H2 Dissolved in Transformer Oil
Stepless Adjust Light
Study of the Smart Voltage Control Strategy Based on Three Types of Dates
Study on Fault Simulation for Pneumatic Actuator Model
Study on Force Sensor Based on Gas Pellicle Loading and Pressure Differentials Enlargement
Study on Motion Equation of Acceleration Sensor with Magnetic Fluid
Study on Pilot Transfer Function Model Gain of Closed-Loop Pilot-Vehicle System
Study on RBF Network Adaptive Control for Robot Loading Based on Uncertainty Compensation
Study on the Time Synchronization System in Coal Mine Grid
Synchronous Control of Airbag Ejection Mechanism for Underwater Logging Device
The Design of the Dynamic Detection System for the Screw's Lead Precision Testing
The Influence of Beam Polarization Degree on SPR Phase Sensor
The Liquid Surface Pressure Control System for Low Pressure Die Casting Based on Fuzzy PID
The Measurement and Application of a Cesium Optical-Pumping Magnetometer Magnetic Field Gradient Tolerance
The Moving Target Detection under Complicated Background Base on BP Neural Networks
The Research of Intelligent Greenhouse Alarm System Based on CC2530
The Research on the Encryption Transmission of the Intelligent Robot's Remote Information
The Research on the Measure System of the Shield Tail Clearance Based on Digital Image Processing Technique
The Summary of Tunnel Boring Machine Control Based on the Neural Network
The Test System Design of Multi-Junction Solar Cell Spectral Response
The Design of Household Automatic Control Water Supply System Based on PLC
Trajectory Planning Research of the Filter Shell Special Arc Welding Robot
Vision Servo System for High-Voltage-Live-Working Robot
Research on Precision Measurement of Machine Part Based on Radiometric Calibration
Design of an Intelligent Entrance Guard System with Multiple Identity Authentication
A New Method Based on Position Sensitive Detectors to Measure Four-Degree-of-Freedom Geometric Errors of Linear Guide Rails
Anti-Glare Device for Car Based on Single Chip Microcomputer
Design and Analysis of a Security Alarm System for Railway Transport of Large Equipment Based on Displacement Detection
Design of Machine Tool Setting and Parameter Optimization
Differential GPS Terminal Shooting Range Positioning System Design
Finite Element Analysis of the Mechanical Structure in Portable Exoskeleton Based on DOF Coupling
Hardware Design of a Planar Platform for Naro-CMM
Modeling and Simulation Based on AMESim and Simulink Electric Hydraulic Power Steering System
Research and Practice of the Solution for the Linearity Error Using AGC
Research on Aluminum Electrolytic Multi-Fault Diagnosis Method Based on Immune Genetic Algorithm
Research on Fault Injection Technique for Auto-Loader Based on PLC
Study on Application and Realization of Integrated Control to Medium-Frequency Induction Heating
Study on the Error Analysis of Pipeline Inspection Robot Mileage Wheel Localization
The Integrated Simulation on Power Source of Hydraulic Hybrid Vehicle
The Jacobian Matrix Structure of the Barrier Arm of Inspection Robot
Chapter 4: Mechanical Engineering and Manufacturing
A Replaceable Refiner Plate and Method of Manufacture
A Study on Modeling the Temperature of Vehicle Transmission Device
Acoustic Emission Evaluation of the Pitting Corrosion Damage on the Cut-Stubble Disc Sickle
Acoustic Emission Monitoring on Crack Growth of Wind Turbine Blade Made of Fiber Glass Epoxy Plastic
Analysis of Finite Element and Optimization Design of Mechanical Excavator Rotary Platform
Analysis on Characteristics of Minor Cycle Errors in Process of Grinding Involute Gears on Worm Wheel Gear Grinding Machine
Analysis on Simulation and Experiment of the Drill-Pipe Cross-Section Deformation of Ultra-Short Radius Radial System
Application Research on the Small Wind Generator Based on the Motor Winding Embedding Principle
Automatic Sorting Machine for Cylinder Length
Based on the CFD Technologys Negative Pressure Chamber Air Flow Field Simulation Analysis of the Aspiration Drum Precision Seeding Mechanism
Calculating of the Exit Burr in Low Frequency Axial Vibration Drilling
CFD Simulation Research for Laminar Flow Cooling during Hot Strip Mills
Characteristics of Vehicle Tire Tread Pattern and its Application in Forensic Science
CNC Milling Tool of Choice to Explore
Design and Analysis of ADAMS Simulation for a New-Type Automobile Steering Mechanism
Design and Implementation of a Novel Photovoltaic Water Pumping System Using Energy Storage Technology
Design and Optimization of Dual-Redundancy Transmission System
Design and Structure Strength Analysis of Double-Deck Prestressed Sectional Female Die
Design and Study of outside Wrapping Machine of Sewing Thread Barrel
Design of a Microfluidic Dielectrophoretic Chip for Trapping Two Particles
Design of a New Type Low Heating Vapor Recovery Pump
Design of Small Buoys
Development of a Small Aquatic Cutting Machine
Development of Metal Sheets Hydraulic Deep Drawing Tooling
Dynamic Analysis of Gear Mesh for Gear Pump Based on ANSYS Workbench
Dynamic Modelling and Simulation of Electromechanical Systems Based on Vector Bond Graph
Dynamic Performance Analysis of Submarine Screw Compressor Deballasting System
Dynamic Performance Simulation of Overhead Contact System for over 350km/h High-Speed Rail
Dynamic Response of SFD-Sliding Rigid Bearing Rotor -System
Dynamic Responses Analysis of Vehicle and Track Based on Different Train Speed
Dynamic Simulation and Design Improvement of CVT with Diclinic Cam Plate Synchronous Revolution and Internal Power Shunt
Dynamics Simulation Study of the Axial Piston Pump
Electric Connecting Piece Cutting Blanking Punching Compound Die Design
EMD Analysis of Power Harmonics
Experiment Research of Two-Span Rotor-Bearing System with Rub-Impact and Crack Faults
Failure Analysis and Welding Repair for Water Wall Tube Burst of 600MW Station Boiler
Finite Element Analysis for Pendulum Rod Support Based on ANSYS
Finite Element Analysis of Bioprosthetic Heart Valve on Suture Densities
Finite Element Analysis of Glass Lens Molding Process
Finite Element Analysis of the Roll Collar's Temperature Field of Universal Rolling Mill
Finite Element Analysis of the Shock Absorber for Vehicle
Finite Element Analysis of Working Process for Flexible Collet
Finite Elements Prediction of Temperature Field and Thermal Stresses in Thermal Roll of Calendering Process
Fracture of a Finite Medium with a Circular Internal Crack under Hyperbolic Heat Conduction-Prescribed Crack Face Thermal Flux
Geometrical Feature Analysis of the Movement of the New Type of Double-Hemisphere Rolling Gear Globoidal Cam Indexing Mechanism
Hysteresis Characteristic Model of Suspension for Vehicle Dynamics Simulation
Impact of Contact Wear on Bounce Time of ZNII Vacuum Capacitor Switch
Influence on Inertia the Moment of Inertia Matrix of Three Degrees of Freedom Air-Bearing Testbed
Intelligent Gear Fault Recognition Method Based on HWP Sample Entropy and Grey Incidence
Introducing Digitization into the Continuous Cooling Transformation (CCT) Curves
Investigation of Strength and Dynamic Characteristics for the Rolling Mill
Kinematic Analysis and Structure Parameter Optimization of Automobile Wishbone Independent Suspension
Kinematics Simulation and Experimental Study of CVT with Diclinic Cam Plate Synchronous Revolution and Internal Power Shunt
Magnetic Spring and Experimental Research on its Stiffness Properties
Micro-Vibration Control for Ultra-Precision Isolation Platform of Large Grating Ruling Engine
Modal Analysis and Lightweight Design of High-Power Marine Gearbox Based on Topology Optimization
Modeling and Modal Analysis of the Whole Structure of PT7032 Tower Crane Based on Finite Element Method
Natural Vibration Analysis for Gun Using Rigid-Flexible Coupling Multi-Body Modeling Method
Natural Vibration Analysis of High-Speed Railway Slab Tracks under Rail Longitudinal Force
Numerical Analysis of the Flow in a Curved Duct
Numerical Simulation of a Circumferential Cutting Warhead about Anti-Light Armor
Numerical Simulation of Suction Valve Internal Flow Field of Large Scale Diaphragm Pump Fluid End Based on ADINA
Numerical Study for a Bilayer Functionally Graded Cantilever Beam
Optimization Design of Precast Casing Pipe Unit
Optimization of Supply and Exhaust Stroke of the Electro-Pneumatic Changeover Valve
Parallel Simulation of Scramjet with Multilevel Hypergraph Partitioning
Parameters Calibration for Medium Hydraulic Excavator Simulation Model Based on Experimental Data
Prediction and Analysis of Combustion Chamber Thermal Load of Heavy Vehicle at Different Altitudes
Profile Design of the Helical Groove Milling Tool
Reliability Optimization Design of Planetary Gear Reducer
Research of Voltage Sag Propagation through Transformers
Research on Applications of EPKS C300 System to Steam Turbine and Boiler
Research on Cumulative Damage for Airborne Vehicle under Landing Impact
Research on Hysteresis Characteristic Model of Wheel Carcass
Research on Lifting Capacity of Truck Crane Based on Improved Bicubic Interpolation
Research on Mechanical Balance of the Beam-Pumper
Research on NDT Technique for Thick-Walled Metal Parts of Power Stations
Research on Nonlinear Vibration and Bend Strength Character of WN Gear Pairs in Meshing
Research on Optimization Design of Folding Tables and Chairs Group Based on ADAMS
Research on Temperature Effect on the Natural Frequencies of Continuous Beams Based on Stochastic Subspace Identification
Research on the Structure Strength and Vibration Mode of Transformer
Secondary Cooling Water Distribution Strategy for Beam Blank Continuous Casting
Simulation Analysis of Reciprocating Cutter Based on ADAMS
Simulation Research of Angle Action on Fold-Type Board in Air-Heating Collector
Stiffness Characteristics of a Rotor Shaft with Slant Crack Including Elliptical Front Edge
Study in Interface Appearance Design of Postal Equipment Based on Man-Machine Engineering
Study on a New Earth-Fault Distance Protection for Four-Circuit Transmission Lines on the same Tower
Study on Dynamic Characteristics of Hydraulic Pressure System of MPM Tube Rolling Mill
Study on the Flow Behavior of Underbalanced Circulative Micro-Foam Drilling Fluid
Study on the Multiple Effects of Flow between Two Air Jet Flows of Different Eddy Structure in Channel
Study on Vibration Friction Mechanism of Vibration Compaction System
The Analysis and Application of Machine Tool Spindle Self-Grinding Method
The Angle Distribution of the Spheroid Particle upon Optical Surface
The Control Method and Application on Weld Mark Optimization of Complex Injection Parts
The Design of Compound Die for the Drawing Parts with Holes in Flange
The Design of the 3D Model to Create Injection Mold Cavity Based on Pro/E
The Design of the Integration Intelligent Melting Point Apparatus
The Elastohydrodynamic Lubrication Analysis of Composite Material Gear
The Finite Element Analysis of Double-cabin Storage Tank in Multiple Loading Conditions
The Improvement of the Spin Coater and its Patented Project Design
The Modeling and Simulation of Two-Way Cartridge Check Valve Based on the AMESim
The Research of the Servovalve Noise
The Study and Application of Comprehensive Evaluation of Regional Power Grid Power Quality
The Mechanical Excavator - Hydraulic System of the Establishment of Co-Simulation and Optimization
Topological Optimization Design of the Vertical Machining Center Workbench Based on ANSYS
VDT and its Application to Container Loading Device
Vibration Characteristics Analysis of a Pair of Aviation Herringbone Gears
Vibration Control in Turning Machining
Virtual Prototype Based Fatigue Life Research on some Missile Erecting System
Force Analysis of Pulp Fiber Particle in the Flow Field and Eulerian Two-Phase Flow Equation
P Wave Propagation in the Functionally Graded Materials
Research on the Break Impact Test of Ultra High Voltage Composite Strain Insulator String
Study on the Conversion Method of Three-Dimensional Shape Prediction Model of BGA Solder Joints
Study on PLCC Lead Free Solder Joint's Thermal Reliability Based on Shape Prediction and Response Surface Methodology
The Numerical Simulation Analysis of Tuyere's Temperature Field and Stress Field
A New Intelligent Fault Recognition Method for Rotating Machinery
A Novel Method to Extract Carrier Mobility and Threshold Voltage in High-Voltage DDD MOSFETs
A Comparison of Peer-to-Peer Simulator
A Contactless Sensing Analysis of a CUP Wafer
A New Improved Entropy Method and its Application in Power Quality Evaluation
A Numerical Study of Underwater Explosion Bubble
An Electronic Model of Capacitor Charging Power Supply Considering Transient Switching Interference
An Integrated Numerical Model for a PEM Fuel Cell System
Analysis on Electrical Connector Corrosion in Southeast Coastal Areas
Application of Gray Elman Neural Network to Predict the Gas Emission Amount
Applications of DC Transformer in DC Distributed Generations System
Band-Pass Digital Filter Window Function Method Design and Spectrum Leak Analysis Based on MATLAB
Bearing Fault Diagnosis Based on Wavelet Analysis
Calculation of Follower Displacement Error for a Translating Roller-Follower Plate Cam
Combined Improved EEMD with SVM in the Application of Intellgent Fault Diagnosis
Design and Analysis of Bicycle Helmet with Impaxx Foam Liner
Harmonic Responses of Blades with Piezoelectric or Piezomagnetic Coatings
Ka-Band Satellite Channel Multi-State Markov Model Based on Dust Storm Weather and Shadow Multi-Path Effects
Loose Detecting of Tower Crane Bolts Based on Time Series Analysis
Research on HOV Space Motion Mathematical Model
Research on Nonlinear Numerical Simulation Method of Icing Conductor on Galloping
Research on Predictive Model of Gas Concentration for Driving Ventilation in Coal Mine Based on RBF and BP
Simulation Study on Power Load Characteristics Influence Voltage Collapse Process
Study on Thermal Performance of a New Solar Air Heating Collector
Study the Propeller Blade Impact on Powder Mixture
The Eigenvalue Problem and Saint-Venant Decay Rate for a Nonhomogeneous Semi-Infinite Strip in Plane Strain
The Research on the Theory of Flow and Method of Ripple Control of the External Gear Pump Group
Theoretical Analysis & Experimental Research on Piezoelectric Vibration Feeder by Vertical Driving
Study and Practice of Time-Temperature-Transformation (TTT) Curve Digitization
Chapter 5: Data Processing, Computer and Information Technologies
An ASP Based Approach of Inter-Domain Role Mapping
A New Algorithm of Design of Fixturing Scheme Based on RBR and CBR
A Fast Convex Hull Algorithm of Planar Point Set
Button Cell Characterization Testing Technology Research Based on Computer Vision
Color Features Description and Extraction of Flame Image Segmented Region of Early Fire in Large Space
Damaged Ship Anti-Flooding Decision Plan Intelligent Generation System Based on Petri Net and Heuristic Color Genetic Algorithm
Design of the Post-Processor for Rotors Dynamics Based on the STEP Standard
Human Face Detection Method Based on Skin Color Model
A Face Detection Method Based on Log-Gabor Filters
Human Motion Tracking Based on B-Spline Snake Algorithm
Implementing Sparse Matrix Ordering Using Hypergraph Partitioning
Multi-Domain Modeling Simulation and Application Based on MapleSim
Research and Application of Equipment Fault Diagnosis Based on Cloud Computing
Research on Application of Intelligence Schedule of City Pubic Traffic Vehicles Based on Genetic Algorithm
Simulation of A/D Conversion with LabView
Software Maintainability Modeling Based on Probability at Design Level
Study of Speaker Recognition Based on Multiclass Core Vector Machine
The Design and Application of Quality Information Management System of the Assembly Line of Engine
The Power Spectrum Estimation of the AR Model Based on Motor Imagery EEG
The Spatial Classification Algorithm of K-Nearest Neighbor Based on Spatial Predicate
Comprehensive Assessment Method of Equipment Support Exercise
Design and Implementation of Multiple Linked Lists Sharing the same Memory
Design of a Scene Federate in the Proving Ground Simulation Platform
Digital Model Construction by Reverse Engineering Design Based on Geomagic Studio and Pro/E Software
Equipment Support Training Level Evaluation Method based on ANFIS
Meso-Scale Oriented Physical Simulation Model for Complex Product Maintenance in Virtual Environment
Parametric Design and Automatic Adjustment Technique of Engineering Drawing Based on SolidWorks
Software Tool Used for Transformer Design in AutoCAD Environment
Study and Simulation Analysis of OFDM System Based on Simulink
Study on a MES-Based Large Blast Furnace Expert System
The Parametric Design and FEA of SolidWorks Based on the VB
Chapter 6: Engineering Management and Product Design
A Grid Flow Management System for Resource Allocation Problem
Aviation Oil Demand Combination Forecasting Based on Vectorial Angle Cosine
Condition-Based Maintenance and State Diagnosis of Electric Equipment
Design for Energy Optimization Method Based on Energy Unit
Flight Safety Assessment of Airlines Based on Analytic Hierarchy Process
Fuzzy Comprehensive Evaluation on Regional Development Level of General Aviation in China
Logistics Demand Forecasting with Asymmetry-Width Probabilistic Fuzzy Logic System
Multi-Agent Technology Application in the ASCM Model
Refined Oil Repository Safety Assessment Studies
Research on Green Procurement Model Based on Green Supply Chain
Research on the Construction Method of ERP System Structure of Lu Brocade Enterprises
Satisfaction Measurement of the Automobile Manufacturing Suppliers Based on Fuzzy Comprehensive Evaluation
Study on Evacuation Facilities Bottleneck in Xizhimen Station with Simulation
Study on Low Frequency Load-Shedding of Substitute District
System Availability Test Procedure with Minimum Operating Time
The Application of BP Neural Network Learning Algorithm Based on the Particle Swarm Optimization
The Application Status of Weapons Fault Diagnosis Technology
The Asymmetry-Center Probabilistic Fuzzy Set for Freight Turnover Forecasting in Changsha City
A Study on the Impact of Virtual Manufacturing on Corporation Management
Brief Discussion on Manufacture and Application Value of Modern Paper-Cut Animation
Culture Features in Car's Headlights Form Design
Feasibility Study on Material Selection of Corporate Brand Image Design
Operation Management of Port Logistics in the Global Supply Chain
Product Form Designing of Mechanical Engineering Based on the Theory of TRIZ
Quality Evaluation Model for Highway General Mechanical and Electrical Product
Research on Emergency Plan Management System for High-Speed Railway
Research on Formulation and Implementation of Mechanical Equipment Repair Process
Research on Resource Optimization of Special Maintenance Vehicle Operation Based on Genetic Algorithm
Research on the Process of Conceptual Design for Hoisting Machinery Based on Directed Graph Model
Study on Driving Fatigue Based on Ergonomics
The Analysis of Categories of Users in Car Design
The Study of Large Equipments Condition Maintenance Policy Based on Kalman Filtering
The Application Research of the Traditional Materials Based on the Green Design of Products
「Nielsen BookData」 より