Advances in material science, mechanical engineering and manufacturing : selected, peer reviewed papers from the 2013 3rd International Conference on Machinery, Materials Science and Engineering Applications (MMSE 2013), June 20-21, 2013, Wuhan, Hubei, China
Author(s)
Bibliographic Information
Advances in material science, mechanical engineering and manufacturing : selected, peer reviewed papers from the 2013 3rd International Conference on Machinery, Materials Science and Engineering Applications (MMSE 2013), June 20-21, 2013, Wuhan, Hubei, China
（Advanced materials research, v. 744）
Trans Tech Publications, c2013
- : pbk
Available at / 1 libraries
-
No Libraries matched.
- Remove all filters.
Note
Includes bibliographical references and indexes
Description and Table of Contents
Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).
Collection of selected, peer reviewed papers from the 2013 3rd International Conference on Machinery, Materials Science and Engineering Applications (MMSE 2013), June 20-21, 2013, Wuhan, Hubei, China.
The 128 papers are grouped as follows:
Chapter 1: Manufacturing and Mechanical Engineering, Equipment, Design and Simulation, Analysis of Dynamic Systems;
Chapter 2: Advanced Materials and Material Science, Materials Processing and Machining;
Chapter 3: Devices Design;
Chapter 4: Automation and Control Technologies, Sensors;
Chapter 5: Electrical, Energy and Power Systems Engineering;
Chapter 6: Related Themes.
Table of Contents
Preface and Organizing Committee
Chapter 1: Manufacturing and Mechanical Engineering, Equipment, Design and Simulation, Analysis of Dynamic Systems
Analysis for Wedge Falling-Proof Brake Assembly of Lifter with Converter Oxygen Lance
An Improved Model Reduction Method and its Application in Similar Simulation of Complex Systems
Simulation and Experiment Research of Working Process of Exhaust Turbocharged and Intercooled Diesel Engine
The Effects of the Manufacturing Errors of a Group of Sprags on the Engagement Properties of Sprag Clutch
Optimization Design and Simulation Research of Hydraulic Test Bench
Electro-Mechanical Coupled Characteristics of Piezostack Actuator under the Combined Loads
Research on Performance of Stern Shaft Mechanical Seal Based on FLUENT
Analysis and Research of the Combustion Process of YN4100QB Diesel Engine
The Simulation of Vibration Mechanism and Dynamics Analysis of Eccentric Shaft of Billet Caster
Study on Structure and Performance Optimization for Spherical Stern Bearing Based on ANSYS
Optimization Design Research on Descaling Bit of Water Pipeline Wall
Development of Premium Threaded Connections for Casing and Tubing
Experimental Investigation on Power Consumption in Reactor Coolant Pumps with the Function of the Flywheel
Modeling and Simulation of Chinese SONG Telescope
Mechanism Configuration of Super-Redundant Robot
Mechanism Design and Kinematics Positive Solution of the Exoskeleton Upper Limb Rehabilitation Robot with 6-DOF
Lightweight Design for a New Tracked Triangular Wheel Structure
Value of Cepstrum Analysis and its Application in Gearbox Fault Diagnosis
The Influence of Gearbox Oil-Leak to the Bolt Joint in Wind Turbine Tower
Research on Fixturing Method of Marine Crankshaft Finish Machining
The Research of Lubricating and Colling System of the Low-Speed and Heavy-Load Sliding Bearing
The Research on Heat Transfer Coefficient of Wheel Rims of Large Capacity Steam Turbines
The Analytical Research and Development of On-Line Monitoring Models of Thermal State for Turbine Rotor
A Lifting Device for the Maintenance of Great Mining Height Supports
Leakage Simulation of the Impactor of Hydraulic Rock Drill
Structure Design of the Hydraulic Support Sprag Units for Great Mining Height
Study on Large Inclined Angle Integrated Caving Hydraulic Support Stability Control
Study on Fully-Mechanized Face Quick Withdrawal Suite of Hydraulic Support Design and Application
Design Application of LQS20000 Column Strength Test Bench
The Influence of Different Resistance on Stability of Curve Jointless Line
Experimental Modal Analysis of the Industrial Flat Sewing Machine Based on PolyMax Algorithm
Conceptual Design and Optimization of Submarine Escape Capsule
Application and Study of Fuzzy Neural Network Theory Based on Takagi-Sugeno Model to Thermal Error Modeling on NC Machine Tool
Self-Moving Tail Prototyping and Structural Improvements
Modal Finite Element Analysis of Double Rollers Plastic Calender Equipment
Study on the Constitutive Behavior and Damage Evolution in the FPZ of WST Specimens Using the Vic-2D and Strain Gauges
Dynamics Analysis in Rigid-Flexible Coupling of Reinforced Steel Length Bodies with Friction Wheel
A Novel Approach for MEMS Vacuum Packaging
Research on Design and Optimization on Balance System of Large Floating Crane
Exact Solution of High-Speed Couplings for Interference Fits
Numerical Extrapolate Analysis of Joint Wear in Plan Multibody Systems
Theoretical and Finite Element Analysis on Connecting Rod of Quintuple Cylinders Fracturing Pump
Lubrication Model and Dynamic Characteristics of Distributed Liquid Film for Hydrodynamic Bearing
The Techniques in Developing Finite Element Software for Creep Damage Analysis
The Validation of Computational FE Software for Creep Damage Mechanics
Three-Dimensional Simulation of the Intake Port Combination Effect on Intake Flow Characteristic in a Highly Intensified Diesel Engine
Research on NOx Emission Characteristics of Medium Speed Diesel Engine
Study on Influence of Insulating Clapboard in the Process of Electrolytic Cleaning for Cold-Rolled Strip
Study on the Working Principle of a New Type of Power Transmission Mechanism for Gasoline Engine
Analysis of the Mechanical Interlock Sliding in Self-Pierce Riveting Joints
An Ellipse Fitting Algorithm Applied to the Construction of the Elliptic Arc-Shaped Leading Edge
Concept Exploration on the Design Requirements and Design Scheme of Laser Shock Processing Equipment
Reasons of Great Mining Height Coal Side Fall and Study of Supports Preventing Technology
Analysis of Combustion and Emission Characteristics of Diesel, Natural Gas Dual Fuel Engine
Research on Micro-Stepping Driving System of Three-Phase Hybrid Stepping Motor
Develop Radiator Core Shape Parametric Modeling Software Based on Fluent Secondary Development Using VC++
Non-Contacting Carbon Seal for High-Temperature and Large-Diameter Turbomachinery Applications
Chapter 2: Advanced Materials and Material Science, Materials Processing and Machining
Improvement in Mechanical Property of SiO2 Films Prepared by Sol-Gel
Updated Research Result on Transverse Corner Crack of Slab
Research Development on Performance of Industrial Insulation Coating
Process Design on Baogang 2250mm Hot Rolling Project
Effects on the Structures and Properties of APMOC Fiber from Hydrothermal Aging
Dispersive Behavior of Carbon Nanotubes in Aqueous Solution
Influence of Composite Modifier on the Modification of Calcium Carbonate Powder
Mixing Short Fiber-Rubber Composite by New Rotor with Variable Clearance
Influence of Ag Micro-Addition on the Glass Forming Ability, Thermal Stability and Compression Performance of Cu-Based Metallic Glasses
The Silver-Loaded Diatomite Prepared by Ion Exchange and its Antibacterial Effect
Structural and Magnetic Properties of CoFe2O4 / Si (001) Thin Films via Sol-Gel Method
Effect of Solvent to Fingerprint Detection by Photoluminescent CdSe/PAMAM Nanocomposites
Broadband Dielectric Spectroscopy Analysis of Dielectric Properties of Barium Titanate Ceramics
Study of Direct Quenching and Tempering Process of a Low Carbon Equivalent 960 MPa Grade Steel
Influence of Powder Preparation Technology on In Situ Reactive Synthesized Ti (C,N)-TiB2 Composite Ceramics
The Influence of the Al-Ti-B/Al-Sr Modification on the Microstructure and Properties of the Hypereutectic Al-Si Alloy in Automotive Piston
Ferromagnetism Switched by Hydrogenation in Layered MoS2
Microstructure and Mechanical Properties of Austempered High Boron Cast Iron with Modification and its Mechanism Discussion
Synthesis of New Luminescent Materials and Application as Sensitive Chemosensors
Effect of Rare Earths and Vanadium on Microstructure and Mechanical Properties of High Chromium Cast Iron
Bending Performance of Carbonized Bamboo Scrimber and Fracture Morphology Analysis after Different Ageing Treatments
Research on the Bending Properties of the Bamboo-Wood Container Flooring
The Preparation of Honeycomb Cordierite Mn-Ce/TiO2 Catalyst and Denitration Performance
Influence of Thermo-Electropulsing Rolling Process on Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Strip
Development of 60Si2CrVNb High Tensile Strength Spring Steel
The Analysis and Tests of Composite Leaf Spring for Trailer Truck
Microstructure and Hot Corrosion Properties of Surface Plasma Alloyed Ti2AlNb-Based Alloys
Overview of Axial Compression Technology for Direct Capture of CO2
Research on Preparation of Nanocrystalline Titanium Oxide Film and its Super-Hydrophilic Property
The Mechanical Properties of Low Cis-Butadiene Modified HIPS
Fluorinated MWCNT Used for Cathode of Primary Lithium Battery
Review of Creep Cavitation and Rupture of Low Cr Alloy and its Weldment
Analyzing the Characteristics of the Cavity Nucleation, Growth and Coalescence Mechanism of 9Cr-1Mo-VNb Steel (P91) Steel
Research of the Halogen Phosphate Green Luminescent Materials Prepared by Sol-Gel Microwave-Assisted
The Preparation and Luminescence Properties of Stannate Red Phosphors for WLED
Effection of Additive on Aluminum Nitride Nano-Wire Synthesis by Double Decomposition Method
Experimental Research on the Mechanical Behavior of the Cracked Aluminum Plate Bonded by the Graphite/Epoxy Composite Patch
Experimental Research on the Stiffness of CFRP Reinforced Concrete Beam
Influence of Process Parameters on the Quality of Bionic Non-Smooth Coatings by Laser Cladding
The Influence of Aging on the Flexural and Physical Performance of Restructured Bamboo Lumber
The Validation of Computational Software System for Creep Damage Analysis
Study of Stiffness Calculation Method on Reinforced Concrete Beam Strengthened with CFRP
Chapter 3: Devices Design
Optimizing Design of the Guide-Vane Attached to the New Bidirectional Flowmeter
The Design of a New Biaxial Decoupled Resonant Micro-Accelerometer
Design and Application for Heller System Radiator Built-In Automatic Cleaning Device
Non-Uniform Dose Measurement Based on Two-Stage Bleaching Integrated with Thermo-Luminescence and Optically Stimulated Luminescence Dosimeter
The Design and Simulation of a New Z-Axis Resonant Micro-Accelerometer Based on Electrostatic Stiffness
Chapter 4: Automation and Control Technologies, Sensors
Design of Hall Vehicle Speed Sensor Comprehensive System
Design of Tools Flow Based on Reusable Scheduling in FMS
Analysis of the Sensory Perception Factor in Product Design of Infant
Robot Soft Grabbing with New Piezoresistive Tactile Sensor
Long Range Inspection of Rail-Break Using Ultrasonic Guided Wave Excited by Pulse String
Research on Application of High Precision Angle Encoder in Antarctic Telescope
Design and Implementation of a Control System for Manipulator Based on PLC and the Kingview
A Study on Control Strategy under Tip-In Condition Based on AMT Vehicle
Study on Active Vibration Control
Design of Wireless Monitoring Environment System Based on AVR SCM
Mathematical Models for VLSI Placement with Rectilinear Embedding
Speed Measuring Experiment System Based on LabVIEW
Chapter 5: Electrical, Energy and Power Systems Engineering
Design of Power Supply System for 10kV Smart Switch Based on PV Technologies
A New PDM Power Control Technology for the Resonant Inverter
A Research on the Application and Calculation of Wind Energy
Research on the Influence of Wind Energy on New Energy Utilization Coefficient of EEDI
Exergetic Cost Analysis of Marine Diesel Engine Waste Heat Recovery System Based on Matrix Model Thermo-Economics
Challenges of Battery Pack to the Industrialization of Battery Electric Vehicles and the Corresponding Solutions in China
Chapter 6: Related Themes
Research on the Customer Requirement Processing for Mass Customization
Adaptive Algorithm Designed for Enterprise's Agile-Transformation
The Research on Product Quality Competitiveness Based on Innovation
Enterprise Logistics Network Optimization Based on Genetic Algorithm
Improving Design of Household Self-Traction Treatment Bed
A New Method of Building an Evaluation Model for User Interface
by "Nielsen BookData"
