Advanced materials and process III : selected, peer reviewed papers from the 3[rd] International Conference on Advanced Design and Manufacturing Engineering (ADME2013), July 13-14, 2013, Anshan, China
著者
書誌事項
Advanced materials and process III : selected, peer reviewed papers from the 3[rd] International Conference on Advanced Design and Manufacturing Engineering (ADME2013), July 13-14, 2013, Anshan, China
（Applied mechanics and materials, v. 395-396）
Trans Tech Publications, c2013
- : [set]
- Part 1
- Part 2
- タイトル別名
-
ADME 2013
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
[rd]: superscript
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the 3rd International Conference on Advanced Design and Manufacturing Engineering (ADME 2013), 13-14 July, 2013, Anshan, China.
Volume is indexed by Thomson Reuters CPCI-S (WoS).
The 250 papers are grouped as follows:
Chapter 1: Composites;
Chapter 2: Micro/Nano Materials and Technology;
Chapter 3: Metal alloys and Mineral Prospecting and Exploration;
Chapter 4: Steel and Iron;
Chapter 5: Polymer Materials and Technology;
Chapter 6: Building Materials, Civil and Geoengineering, Construction Technology;
Chapter 7: Biomaterials, Biotechnology and Environmental Friendly Materials Engineering;
Chapter 8: Surface Engineering/Coatings;
Chapter 9: Mechanical Behavior, Tribology and Fracture;
Chapter 10: Structural Strength and Stability;
Chapter 11: Materials Forming;
Chapter 12: Materials Machining and Processing Technologies;
Chapter 13: Welding and Joining, Applications;
Chapter 14: Modeling, Analysis and Simulation of Manufacturing Processes.
目次
Preface and Conference Organization
Chapter 1: Composites
Study on Compressive Properties of SiC Particle Reinforced ZAlCu5Mn Composite Foams
Research on Nong'an Oil Shale Hydraulic Breaking
Research on Metallurgical Reactivity Performance of Coke
Fabrication of PLGA/MWNTs/HA Scaffolds for Biomedical Application
Optical Properties of Fe-Doped TiO2 Thin Film Prepared by Sol-Gel
Numerical Simulation of UHMWPE Laminated Fiber Plate Resisted Projectile
Fabrication and Dielectric Characterization of a Novel Polyimide
Raman Spectral of Ce/Mn Co-Doped LiNbO3 Crystal
Preparation and Electromagnetic Shielding Effectiveness of a New Kind of Electromagnetic Shielding Composite Coatings
The Influence of Work Parameters on a Hydrogen PEM Fuel Cell Efficiency
Influences of Environment-Friendly Additives on Electrochemical Properties of Aluminum Anode Materials in 4 Mol/L KOH Solution
The Preparation and Electrochromism Property of Vanadium Pentoxide
Failure Analysis of a Composite Frangible Cover Based on Transient Dynamics
Optimization of Bubble Amount in Resin Mineral Composite Based Vacuum Pouring Procedure
Experimental Research on the Effects of Dimension on the Impact Damage of CFRP Laminates
Threshold of Impact Energy on the Medium Leakage of CFRP Laminates
Synthesis and Mesomorphism of Novel Star-Shaped Liquid Crystals Containing Donor-Acceptor Groups
Buckling Analysis of Carbon Fiber Reinforced Plastics Cylinders under Axial Compression
Chemical Composition of Cerium and Manganese Co-Doped Lithium Niobate Single Crystal
Modulations and Core-Shell Effect on Positive Temperature Coefficient of Resistivity of Na0.5Bi0.5TiO3 Ceramics by Electrically Heterogeneous (LiCe) Phases
The Electromagnetic Interference Shielding Effectiveness of Carbonized Bacterial Cellulose Coated with Nickel by Electroless Plating
Stable Electrophosphorescent Emission of Fluorenyltrifluoromethyl-Pyridine Iridium 2-Picolinic Acid at High Concentration
Study on Dispersion Behavior of Al2O3/ZrO2 Composite Powder
Theoretical Studies on Structures and Properties of Pentazine,1,2,4,5-Tetrazine and s-Triazine Derivatives with Nitrogen - Containing Substitutents
Studies on the Aging Resistance of Polypropylene Composites Filled with Mica in High Content
Fabrication and Ultraviolet Characterization of Potassium Sodium Niobate/Polyimide Hybrid Films
Study on Microlens Photonic Crystal Fabricated on Organic Light-Emitting Diode Substrate
Chapter 2: Micro/Nano Materials and Technology
Effect of Content and Layer Thickness on the Corona-Resistance of PI/TiO2 Nanocomposite Films
Electrospun Ketoprofen Sustained Release Nanofibers Prepared Using Coaxial Electrospinning
The Nanocapsulation Research Progress in Food Industry
The Preparation and Tribological Property Investigation of Chrysotile Nanotubes on the Grease
Electroless Plating of Cu on Multi-Walled Carbon Nanotubes
Synthesis of Silver Nanoparticles through the Soft Template Method and their Applications to Surface-Enhanced Raman Scattering
Simulation of the Effect of Nano Phase Size on Microstructure Evolution in Nanocomposite Ceramic Tool Materials
Synthesis and Characterization of N-Doped Meso/Macroporous Carbon
Investigation on the Photovoltaic Performance of ZnO Nanoarrays Prepared by Chemical Bath Deposition and Hydrothermal Method
Preparation of Ni-ZrO2-CeO2 Nanocomposite Coatings by Pulse Electrodeposition
A Straight Nanopore Drilling by Transmission Electron Microscope
Chapter 3: Metal Alloys and Mineral Prospecting and Exploration
The Source of Ore-Forming Material in Barite-Fluorite Deposits, Southeast Sichuan in China: Sr Isotope Evidence
Electrical Erosion Characteristics of Pt-Ir-Zr Alloy Contact under DC Load
Study on the Behavior of Internal Oxidation of Ag-Cu-Zn Alloy
Effect of the Ratio of Zn/Y on Microstructure and Mechanical Properties of As-Cast Mg-4Zn-xY Alloys
Effect of the Linear Electromagnetic Stirring on Microstructure and Properties of Cu-10%Nb Alloys
Study on Molten Zone in Twin-Roll Casting of Magnesium Alloy Strip
The Study about Property of Corrosion Resistance of AlCoCrTiNiCu_x High-Entropy Alloys
Influnce of Grain Size on Dynamic Recrystallization of AZ31 Magnesium Alloy Rolling Sheet
Coal Quality Characteristics and Inflaming Retarding Mode of Indonesia Coal in the Large Power Statdion
Methods for Determining the Physical Property Cutoffs of the Effective Reservoirs of the Yaoyi Formation in Cha 48 Zone
Cyclic Hardening Behavior of Extruded AZ31B Magnesium Alloy during Low Cycle Fatigue Process
Comparison of Oxidation Behavior of Binary Co-10X (x=Al, Si, Cr) Alloys at 973 and 1073K
Effect of Hydrogen as a Temporary Alloying Element on the Microstructure and Mechanical Properties of Ti-6Al-4V Titanium Alloy
Boron Influence on Structures and Properties in Nickel-Based Alloys
The Influence of Ti on d-Electron Occupancy of Fe in Fe-1.7%Ti Alloy
Simulation of the Effect of Sintering Pressure on Microstructure Evolution in Nanocomposite Ceramic Tool Materials
The Application of Magnesium Alloy in Automotive Seat Design
Chapter 4: Steel and Iron
Effect of Cooling Rate on Oxidation Behaviour of Microalloyed Steel
Effect of Intercritical Quenching on Microstructure and Mechanical Properties of Oil Casing Steel N80
Effects of Aging Precipitates on the Mechanical and Corrosion Resistance Properties of 18Cr-18Mn-2Mo-0.96N Super High Nitrogen Austenitic Stainless Steel
Effect of Nano CaO and MgO Addition on the Inclusions Composition in the Cast Microstructure of X80 Pipeline Steel
Effect of Magnesium Addition on the Cast Microstructure of a Kind of HSLA Steel
Investigation on Microstructure, Texture and Tensile Properties of Hot Rolled Strip Casting Grain-Oriented Silicon Steel
Experimental Study on Optimization of Slag Splashing Modifiers with Magnesite Tailings
Research on the Optimization of Heat Treatment Process and the Abrasive Impact Wear Mechanism of 70Mn Steel
Effect of the Continuous Annealing Process on Microstructure and Mechanical Properties of DP590 Steel
The Influence of the Electromagnetic Field Power on the Solidification of the Casting
Study of Precipitation in Continuously Casting Slabs of Microalloyed Steels
Experimental Study on the Oxide Scale of Steel Slab under Oxygen-Enrichment Combustion
Energy Balance Analysis of No.1 Sinter Machine at Baosteel
Electron Microscopic Analysis of 30CrMnSi Steel Surface Layers after Hot Deformation
Microstructure Evolution in Nb-Ti Micro-Alloyed Steel during Hot Compression and Hot Rolling Simulation
Chapter 5: Polymer Materials and Technology
The Study on the Synthesis of Polyfluoroacrylate
Detection of Phthalate Esters from Plastic Packaging Materials into Edible Oil by Gas Chromatography-Mass
Effects of Emulsifier Concentration on Nucleation Mode of Emulsion Polymerization of Methyl Methacrylate
Preparation and Characterization of Hyperbranched Silicone Oil by Hydrosilylation Reaction
Study on Acrylic Emulsion Adhesive Modified by Double Siloxane
Effect of Barium Stearate on the Thermal Stability of Polyvinyl Chloride
Effects of the Water Absorbability of Superabsorbent Prepared by Graft Copolymerization of Acrylic Acid onto Milk Proteins
Research of Arylic-Terminated Hyperbranched Polyester Modified Styrene-Acrylic Emulsion
Synthesis and Characterization of a Novel Aramid Fiber Liquid Crystalline Polymer
Studies on In Vitro Release Performance of Hydrophilic Drugs and Lipophilic Drugs in Amphiphilic SIS-Based Hot-Melt Pressure Sensitive Adhesives
Effects of Emulsifier Concentration on Nucleation Mode of Emulsion Polymerization of Styrene
Effects of Emulsifier Concentration on Polymer Particle Size in Emulsion Polymerization of Styrene
Study on the Curing Reaction and Rheological Behavior of Bismaleimide Resin
Synthesis and Polymerization Kinetics of PMMA in [BMIM]BF6 Imidazolium Ionic Liquids
Preparation and Research of Polymolybdate/Polymer Composite Membrane by Electrospinning and its Photo-Catalytic Property
Study on the Poly (ether sulfone) Microfibers
Study on Synthesis and Properties of Waterborne Polyurethane Modified by Epoxy Resin
Chapter 6: Building Materials, Civil and Geoengineering, Construction Technology
Study of the Parameters of Lightweight Polymer-Cement Repair Mortars Exposed to High Temperatures
A Comparative Study on Production of Autoclaved Aerated Concrete by Coal Gangue Fly Ash
Physical Properties of Waste Concrete Recycled Aggregates According to Coating Factor
Analysis Based on FLAC3D of Surface Subsidence Caused by a Double-Tube Parallel Tunnel Excavation
Application Study of FRTP Materials in the Civil Engineering Products
Progress of Studies on Durability of FRP Rods Used in Civil Engineering
Diagenesis of Volcanic Rocks and its Effects on Evolution of Reservoir Space of Yingcheng Formation in 2,3 Wellblock of Yaoshen Area
Gulong Oilfield Putaohua Oil Layer in the Gu 83 Block Sequence and Sandstone Characteristics Research
Influence of Ground Phosphorous Slag Powder on Performance of Cement Mortar
The Research on Seismic Performance of the Insulation Material on the External Wall of a Building
Discussions on the Construction Technology of the Vibrating Inserting Rod Long Auger Bored Pile-CFA
Analysis of Effects of a Double-Tube Parallel Tunnel Excavation on Underground Pipelines
The Finite Element Analysis of Cross Steel Reinforced Concrete Special-Shaped Columns
Analysis on Earth Stress and Fracture Distribution Characteristics with Image Logging
Microscopic Mechanism Research on Airport Pavement Ultra-High-early Strength Concrete Patching Material
Study on the Cementitious Proportion of Cemented Mine Tailings
The Status Analysis of Constitutive Relation and Parameters of Soil Dynamics
Comparison between SPI and Soil Moisture Retrieved from AMSR-E
Damage Evaluation of Concrete Based on Acoustic Emission b-Value
Effect of Shape and Size of Concrete Specimens on Test Result of Chloride Migration Coefficient
A Numerical Method for the Paving Block Evaluation
Correct Direct Discrete-Continual Boundary Element Method of Structural Analysis
A Brief Analysis of the Floor Crack
Research on Supporting Theory of Pressure-Bearing Ring and Yield Supporting Technology in Extremely Soft Rock Roadway
Application of Reclaimed Ladle Bricks in Magnesium Aluminate Spinel Based Castables
Jacking Force Controlling Technique of PC Beam Flexible Piers Based on Multiple Points Pushing Method
Chapter 7: Biomaterials, Biotechnology and Environmental Friendly Materials Engineering
Isolation and Polyphasic Investigation of the Carotenoids-Producing Marine Bacterium from Trachurus murphyi Chile Fishery
Biodegradation of DCM Vapor in a Biofilter
Kinetics and Thermodynamics Studies of Monascus Red Dyeing on Wool
Experiment on the Mechanics Properties of Hot-Pepper in the Process of Hot-Air Drying
Characteristics of Hydrated Calcium Silicate and Paper Filler
Packaging Mechanical Properties of Composite Paperboard
The Effect and Mechanism of Apoptosis Induced by Desacetylcinobufotalin (DEBF) in Human Hepatocellular Carcinoma HepG2 Cells
Adsorption of Cesium from Aqueous Solution by Modified Montmorillonite
Catalytic Destruction and Removal of Dichloromethane in the Microwave/Fe4O3 System
Study of Extraction of Total Alkaloids from Caulophyllum Robustum
Surface Modification of Activated Carbon and its Effects on Methane Adsorption
Functionalized Mesporous Silica with Ethylenediamine for Removal of Pb(II)
Chapter 7: Biomaterials, Biotechnology and Environmental Friendly Materials Engineering
Degradation of Organics from Laboratory Wastewater by Ultrasonic/Fenton Process
A Study of Basic Properties of Cellulose Ether Modified Dry-Mixed Mortar
The Effect of Water Stress on the Fluorescence Parameters and Growth of Sophora japonica 'Golden Stem'
Sensitive Determination of Eight Paralytic Shellfish Poisoning Toxins in Aquatic Products by LC-MS-MS Method
Carbon Capture Performance of Amino-Modified MIL-101 at Room Temperature
A Comparative Study on Preparation of High Strength Gypsum by Flue Gas Desulfurization Gypsum and Natural Gypsum
Research Progress of the Properties and Application of Bamboo Charcoal
Study on Loading Rate-Dependent Property of Different Layers in Articular Cartilage Based on ABAQUS
The Micro-Mechanical Behavior of Articular Cartilage under Continuous Sliding Load
Mechanical States of Repaired Full-Thickness Defects of Articular Cartilage by Tissue Engineering under Compression
The Impacts of Heat Treatment on the Material Structure and Properties of Mg-4.0Zn-1.0Ca-0.6Zr Bio-Medical Materials
Application of Melt Extrusion Process for an In Situ Polymers Blend of Cellulose with Polyethylene Glycol in the Presence of Ionic Liquid
Response Surface Optimization of Microwave-Assisted Extraction Conditions of Anthocyanins from Black Soybean Hull
Impact of DOM in Reclaimed Water on Nitrogen/Phosphate Adsorption in Sediments
Amplification and Bioinformatics Analysis of IGS1 Sequence of Aurcularia Auricular
Bioinformatic Analysis of rbcL Gene in Lilium
Chapter 8: Surface Engineering/Coatings
Numerical Simulation of Preparation Process of Selective Absorbing Coating Based on Magnetron Sputtering Technology
Development of Thermal Barrier Coatings on AZ91 Magnesium Alloy Surface
Anti-Corrosion Performance of Four Hot Dip Galvanizing Bolts
Effect of Vanadium and Niobium on Abrasive Behaviour of Arc Sprayed 4Cr13 Coatings
Investigating the use of Nanoscale Bilayers Assembly on Stainless Steel Plate to Improve Evaporation
Oxidation Protective Barrier Coatings for Austenitic Stainless Steels at 1100 DegreesC
The Experimental Study on Paint Removal from Aluminum Surface Using Ice Jet
Preparing the Coating of Color Ink-Jet Paper and Investigating its Printing Quality
Hydrothermal Synthesis and Photocatalytic Activities of Bi2WO6 with Different Surfactant
Investigation of Microstructure and Properties of Surface Nanocrystallization Layer by Rolling Technology
The Crystal Orientation of Hydroxyapatite Coatings Affected by the Magnetic Fields on Magnesium Alloy
Mechanical Milling Prepared Ultrafine Al2O3 Particles Utilized in Brush Plating Ni-P-Al2O3 Coatings and Influence of Heat Treatment to the Performance of the Coatings
Preparation and Properties of Photocatalysed Waterborne Styrene-Acrylic Coating
Comparing of Temperatures of Rolling Bearing under the Oil-Air Lubrication to the Spray Lubrication
Based on the DT-CWT Transformation Methods for 3D-Nanometer Roughness Rating Reference
Chapter 9: Mechanical Behavior, Tribology and Fracture
Experimental Study on Tool Wear in NC Dry Milling Resin Sand Mold Materials
Failure Analysis of Tower Axle in the Wet Drawing Machine
Circumference Damage Identification in a Pipe Using Mode Conversion of Longitudinal Guided Wave
Effect of Powder Pretreatment on the Wear of Ultrafine Cemented Carbide Cutting Inserts
Fracture Analysis of the Double-Circular-Arc Gear Reducer Shaft
Method to Obtain the Regular Term in Bonded Dissimilar Materials under Thermal Loading
Investigation of Deformation and Damage of Taylor Impact Test
Calculation of Static Stiffness of Hyperelastic Coating
Microstructural Characteristics and Wear Properties of NiCr/Cr3C2-WS2 Self-Lubricant Wear-Resistant Composite Coating on Ti6Al4V by Laser Cladding
Criterion of Ductile Fracture for GCr15 Bearing Steel
The Montecarlo Method in Application of Fatigue Life Reliability Analysis
Analysis and Models for the Friction Coefficient of a Sliding Bearing
Research on Ceramic of Water-Based Component
Chapter 10: Structural Strength and Stability
Research on Strength Calculation for Local Area under Pressure
Research and Analysis about Partical Compression for Individual Anchored Prestressed End Strength
Research on the Approach for the Assessment of Subsurface Rolling Contact Fatigue Damage
The Experimental Study on the In Situ Stress of SongNan Block
Turbine Rotor Tooth Head and Stress Analysis of Wedge
Optimal Design of Cylindrical Helical Torsional Spring Including Fatigue Reliability
Destruction Analysis of Broadside Multi-Cabin Protective Structure of Warship under Explosion Loading
Precise Stability Analysis of Stepped Telescopic Booms and Practical Algorithm
FEM and Experimental Stress Analysis of a Jib Crane
Effects of Perforation on the Collapsing Strength of Casing
Analysis of Heat Treatment Quality of a Spring Clip with Failure
Numerical and Experimental Studies of Composites Sandwich Structure with a Rectangular Cut-Out
Floating Stability Analysis of Steel Boxed Cofferdam of Dongtinghu Long-Span Bridge
Static Analysis and Experimental Research on Frame of the Hedge Spray Car in the Ultimate Torsion Condition
Chapter 11: Materials Forming
Hot Stamping of Two Different High Strength Steel with Tailored Properties
Numerical and Experimental Study of Forming Limit Diagrams in Sheet Metal Forming and Seamed Tube Hydroforming
Square Head Adjustable Die Device Research on Ship 3D CNC Forming Machine
Study on Influences Mold Shape Imposes on Bread Heating Distribution
Hot Processing Maps and Workability Characteristics of As-Cast 42CrMo Steel during Hot Compression
Thermal Crown Analysis of the Roll Sleeve in Twin-Roll Strip Casting Process
Design an Effective Solution for Stretch Forming of Sheet Metal with a Shorter Free Edge
End Formation of a Round Tube into a Square Section with Reduced Forming Loads
The Design of a Five-Axis Machine for Water Jet Incremental Sheet Metal Forming
Finite Element Simulation of Four-Way Tube Hydroforming
Comparative Analysis of Onestep and Multistep Forming in Automotive I/P Beam Hydroforming Process
Experimental Research and Numerical Simulation Analysis for Hydroforming of an Instrument Panel Beam
Chapter 12: Materials Machining and Processing Technologies
Study on Surface Properties of Big Tilling Depth Rotary Blade for Laser Shock Peening
Reliability Analysis of Alumina-Based Ceramic Cutting Tool's Wear Life by Saddle Point Approximation
Study on an Ultra-Precision Plane Magnetic Abrasive Finishing Process by Use of Alternating Magnetic Field
Special Fixture Designed for the Fine Boring of Auto Engine Cylinder
Experimental Study on Surface Roughness in Quick-Point Grinding Engineering Ceramics
Study on the Machining Principle and Experiment of Grinding
Research on Force and Temperature in Milling Ti6Al4V Titanium Alloy Based on Tool Geometry
Chatter Prediction Based on NC Physical Simulation in Machining Ti6Al4V Thin-Walled Components
Study on Precision Grinding Technique for Large Size Optical Aspheric Lens
Study of the Surface Integrity of Powder-Metallurgy High-Speed Steel (S390) Multi-Cut by Wire Electrical Discharge Machining
Experimental Study on Cutting Force and Surface Roughness for 7050-T7451 Aluminum Alloy of High Speed Milling
The Research on Milling Force in High-Speed Milling Nickel-Based Superalloy of Inconel 718
Optimization of Surface Roughness in Dry Turning of Brass
Study of Semi-Bond Abrasive in Tiny Grinding Wheel Based on Magnetorheological Effect
Electroplated Diamond Wire Saw Applying Ultrasonic Vibration to Cut Polysilicon Experiment and Simulation Analysis
Fractal Analysis of Laser Cutting Heavy Plate Surface Topography
Effect of the Vibration on Machining Gap of WEDM
Study of Electrode Surface Characteristics under Short Single Pulse in Micro Ed-Milling
Study on Micro Electrochemical Machining Technology and its Influencing Factors
The Technique of Ion Beam Etching Polishing
Chapter 13: Welding and Joining, Applications
Research of Composite Coating Composed of Mo Wire and High-Cr Cast Iron Made by Laser Cladding Technology
Welding Quality Controlling by Describing the Shape of Weld Joint of Pipeline Steel through Computer Software
Research on Model of Plastic Flow Heat Transfer during Linear Friction Welding for Low Melting Point Metal
Design of Novel Integrated Heating and Riveting Control System for TB2 Titanium Alloy Rivet
The Design of Power Supply with Feed-Forward Control Method for EBW
Application of Six Sigma DMAIC Methodology in Welding Assembly Quality Improvement
Experimental Analysis of the Nonlinear Normal Static Stiffness of Bolted Joints
Metal Transfer Behavior of Consumable DE-GMAW
Multi-Input Multi-Output Control of Consumable DE-GMAW
Research on Cu-Fe Solid Solution and Plastic Deformation Properties of Explosively Welded T2/DT4C Laminate
The Numerical Simulation of Superplastic Deformation on Ti-6Al-4V Laser Butt Weld Joint
Influence of Scanning Speed on Microstructure and Hardness during Laser Cladding High-Cr Cast Iron
Chapter 14: Modeling, Analysis and Simulation of Manufacturing Processes
Application of Inverse Heat Conduction Problems in the Slab Solidification Process
Ride Comfort Optimisation of Passenger Car Passive Suspension Systems Using ADAMS/ Insight
A Method to Predict the Sheet Metal Deformation under Different Locator Layout
Optimum Design and Analysis of Metal Delivery System for Magnesium Alloy Plates with Twin-Roll Casting Process
Prefabricated Hole Mathematical Model of Flange-Forming of Tee Pipe with Square Branch
Research on the Fatigue Life of Universal Mill Horizontal Roller Ring Applying Fe-Safe
Unified Multi-Error Model for Four Types CNC Machining Center
A Method of Calculating the Dynamic Characteristics of Rubber Isolator
Numerical Simulation of Orientation Distribution on Fibers Suspensions in Planar Extensional Field
Metallurgical Consideration about Abnormal Events during Slab Continuous Casting Process in the Quality Diagnosis Model
Numerical Simulation Analysis of H-Beam Steel Controlled Cooling
Study on Magnetron Sputtering Process of Stainless Steel Particles Sputtering on Copper Substrate Based on LS-DYNA
Modeling Study of Engineering Ceramics WEDM Based on Fuzzy Logic
Casting Filling Simulation Technology Based on Component Wise Splitting Method
Optimization Design Method of the Pre-Manufactured Hole of Flanging
Numerical Simulation of Filling Process in Large Steel-Ingot
Prediction of CNC Thermal Deformation Based on the Compensation Fuzzy Neural Network
Study and Implementation of CNC Lathe Machining Simulation System
Performance Simulation and Analysis of the Progressive Distributor of the Oil-Air Lubrication by AMEsim
Improvement of Electromagnetic Self-Locking Device for Cylinders in High Temperature Gas-Cooled Reactor
FEM Simulation of Main Deformation during Cage Roll-Forming Process
Design of a Semi-Real Simulation Platform for the Cold Rolling Mill
The Effect of Simulated Domestic Wastewater Treatment by Biofilm and Biological Filter Processing
「Nielsen BookData」 より