Manufacturing engineering : selected, peer reviewed papers from the 1st International Manufacturing Engineering Conference (iMEC 2013), July 1-3, 2013, Gambang, Kuantan, Pahang, Malaysia
著者
書誌事項
Manufacturing engineering : selected, peer reviewed papers from the 1st International Manufacturing Engineering Conference (iMEC 2013), July 1-3, 2013, Gambang, Kuantan, Pahang, Malaysia
（Advanced materials research, v. 903）
Trans Tech Publications, c2014
- : pbk
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the 1st International Manufacturing Engineering Conference (iMEC 2013), July 1-3, 2013, Gambang, Kuantan, Pahang, Malaysia.
The 75 papers are grouped as follows:
Chapter 1: Materials and Manufacturing Process,
Chapter 2: Engineering, Manufacturing Automation and Optimization,
Chapter 3: Manufacturing Systems and Management
目次
Preface, Organizing Committees and Sponsors
Chapter 1: Materials and Manufacturing Process
Drilling of Carbon Fibre Composites: A Review
Tool Life and Flank Wear of Physical Vapour Deposited TiAlN Multilayer Coated Carbide End Mill Inserts when Machining AISI D2 Hardened Steel under Dry Cutting Condition
Effect of Tool Path Strategies in Pocket Milling of Aluminium Epoxy
Effect of Cutting Parameters on Tool-Chip Interface Temperature in an Orthogonal Turning Process
Finite Element Analysis of Aluminum-Kevlar/Epoxy Pressure Vessel
Frictional Characteristics of Steel Materials Sliding against Mild Steel
Effect of Different Qualities of Foam on Fill Particle Transport in Horizontal Well Cleanup Operation Using Coiled Tubing
Dry and Compressed Air Cooling Comparative Study on 6061 Aluminium Alloy Drilling Using Coated Drill
Influence of Workpiece Shape on MRR and EWR in EDM of Steel
The Effect of EDM Die-Sinking Parameters on Non-Conductive Materials
The Effect of Pressure on Warpage of Dumbbell Plastic Part in Injection Moulding Machine
Feasibility Study of Casted Natural Fibre-LM6 Composites for Engineering Application
The Structural and Surface Morphology of Annealed ZnO Films
Surface Roughness of Casted LM6 Using Natural Fibre Sand Casting Mould
Assessment of Machining Cost for End-Milling of Ti-6Al-4V Titanium Alloy through RSM-Based Parametric Model
Experimental Investigation on Friction Coefficient of Engineering Polymers Sliding against Different Counterface Materials
Experimental Investigation on Static Mechanical Properties of Glass/Carbon Hybrid Woven Fabric Composite Laminates
Photoluminescene and Fourier Transform Infrared Measurement of Undoped Diamond-Like Carbon Thin Films by Direct Current - Plasma Enhanced Chemical Vapour Deposition
Effect of Substrate Temperature on Structural and Optical Properties of Un-Doped Diamond Thin Film
Microstructure and Tensile Strength of Rapid Manufacturing Parts
Thermal Performance of Polyamide 6/Cloisite 20A Composite Hybrid by Adiabatic Extrusion: A Study on the Influence of Difference Approach of Compounding
Experimental Study of the Static Modal Analysis on Milling Machine Tool
Optimization of Electro Discharge Machining Parameters for Drilling Titanium in Small Holes Using Taguchi Method
The Effect of Vortex Tube Cooling on Surface Roughness and Carbon Footprint in Dry Turning
Study on Potential Waste Insulating Material Properties in Water for Thermal Storage Application
Effect of TiC Particulates on the Microstructure and Mechanical Properties of Aluminium-Based Metal Matrix Composite
Studies on Tensile Properties of Titanium Carbide (TiC) Particulates Composites
Review of Aluminum Chip Machining Using Direct Recycling Process
Comparison of Cooling Performance between High Thermal Conductivity Steel (HTCS 150) and Hot Work Tool Steel (SKD 61) Insert for Experimental Tool Using Finite Element Analysis
The Effect of Various Diameters Orifice Nozzle Coolant on Surface Roughness Performance in CNC Turning
Cutter Path Strategies for Shoulder Milling of Thin Deflecting Walls
Thin Walled Part Warping Overcoming by Honeycomb Ribs Design
Velocity Measurements Using High-Speed Imaging System for Impact Test
Influences of Varying Combination of Feed Rate and Depth of Cut to Tool Wear Rate and Surface Roughness: High Speed Machining Technique in Non-High Speed Milling Machine
Heat Generation Performance of a Homemade Friction Stir Welding Tool
Chapter 2: Engineering, Manufacturing Automation and Optimization
Cooling System for Electric Motor of an Electric Vehicle Propulsion
Analysis of Two-Layered Film Journal Bearing with Partial Slip Surface
Synthesis of Four Bar Slider Mechanism for Finitely Three Separated Positions
Smart Fan Controller Add-On (SMAFAC) for Home Ceiling Fan for Home Power Optimization
Controller Design for Vector Controlled AC Induction Motor Drive Using State-Space Design Methodologies
A Review of Solar Air Heater for Drying of Agricultural Products
From Manufacturing to Logistics: Development of a Kinematic for Autonomous Unloading of Containers
Mechatronical Product Design Combined with Optimized Dynamic Behavior of Components
Position Tracking of Pneumatic Actuator with Loads by Using Predictive and Fuzzy Logic Controller
Robust PID Controller Tuning for 2D Gantry Crane Using Kharitonov's Theorem and Differential Evolution Optimizer
Issue on Calibration of Direct Feed Biconical Antenna in a Semi-Anechoic Chamber Using Standard Antenna Method
Bouc-Wen Model Parameter Identification for a MR Fluid Damper Using Particle Swarm Optimization
Performance Analysis for a Gantry Crane System (GCS) Using Priority-Based Fitness Scheme in Binary Particle Swarm Optimization
Industrial Automation and Manufacturing Systems: Concepts and Applications
Analysis of Threshold Voltage Variance in 45nm N-Channel Device Using L27 Orthogonal Array Method
Effect of Obstacle Angles on Signal Strength for Different Mounting Elevations of XBee Pro Module in Viral Advertisement System
Altitude and Attitude Control of a Trirotor UAV
Automatic Classification of Wood Texture Using Local Binary Pattern & Fuzzy K-Nearest Neighbor
Modeling and Simulation of Swarm Intelligence Algorithms for Parameters Tuning of PID Controller in Industrial Couple Tank System
Modelling and PID Control of a Quadrotor Aerial Robot
Analysis on the Optimal Geometrical Parameters of Topology Power Optimized Coil Based on a Cylindrical Magnet for Vibration-Based Electromagnetic Energy Harvester
Review on Non Uniform Rational B-Spline (NURBS): Concept and Optimization
Chapter 3: Manufacturing Systems and Management
The Development of Green Innovation Measurement Based on Inter Rater Agreement Approach: A Preliminary Study
A Modified Technique for Order Preference and its Application to Supplier Selection Problem
Implementation of Quality Management System in Malaysian Construction Industry
Assessing Sustainability Performance of Polymer Processing: Case Study of Hollow Fiber Membrane
Comparative Study of TQM Practices between Japanese and Non-Japanese Companies: Proposed Conceptual Framework
A Comprehensive and Practical Framework for Reliable Scheduling in Project Management
A Decision Tool for Product Configuration Designs Based on Sustainability Performance Evaluation
Scheduling of Jobs on Identical Parallel Machines to Minimize Total Flow Time Subject to Optimal Makespan
Complexity Planning for Product Design Using TRIZ
Forecasting Demand: Development of a Fuzzy Growth Adjusted Holt-Winters Approach
Integrating Reliability Analysis in Life Cycle Cost Estimation of Heat Exchanger and Pump
Review of Lean Adoption within Small and Medium Sized Enterprises
Multi-Mode Failure Models for Attribute Test Data in Reliability Systems, a Bayesian Analysis Approach Using Multi-Nomial Distribution Model
Learning Improvement of DEA Technique in Decision Making for Manufacturing Applications Using DEA Excel-Solver
Critical Success Factors of New Product Development and Impact on Performance of Malaysian Automotive Industry
Prioritizing Lean Manufacturing Practices in Small to Medium Enterprises by Applying TOPSIS in Fuzzy Environment
Antecedents of Knowledge Quality-A Conceptual Study among Malaysian SMEs
Feasibility Study of Additive Manufacturing Technology Implementation in Malaysian Automotive Industry Using Analytic Hierarchy Process
「Nielsen BookData」 より