Achievements in engineering sciences : selected, peer reviewed papers from the 2014 3rd International Conference on Manufacturing Engineering and Process (ICMEP 2014), April 10-11, 2014, Seoul, Korea
著者
書誌事項
Achievements in engineering sciences : selected, peer reviewed papers from the 2014 3rd International Conference on Manufacturing Engineering and Process (ICMEP 2014), April 10-11, 2014, Seoul, Korea
（Applied mechanics and materials, v. 548-549）
Trans Tech Publications, c2014
- : [set]
- Part 1
- Part 2
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
Other editors: You-Jin Park, Bale V. Reddy and Amanda F. Wu
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the 2014 3rd International Conference on Manufacturing Engineering and Process (ICMEP 2013), April 10-11, 2014, Seoul, Korea.
The 378 papers are grouped as follows:
Chapter 1: Advanced Materials Engineering and Processing Technologies,
Chapter 2: General Mechanical Engineering and Applied Mechanics,
Chapter 3: Applied Thermodynamics, Heat Transfer, Energy Conversion,
Chapter 4: Instrumentation, Measurement Technologies, Analysis and Methodology,
Chapter 5: Electronics and Integrated Circuits, Embedded Technology and Applications,
Chapter 6: Electrical Engineering and Electric Machines,
Chapter 7: Power System and Energy Engineering, Its Applications,
Chapter 8: Mechatronics and Robotics,
Chapter 9: Control and Automation of Manufacturing,
Chapter 10: Signal and Image Processing, Data Mining and Computational Mathematics,
Chapter 11: Communication, Networks and Information Technologies,
Chapter 12: New Technologies, Methods and Technique in Civil Engineering,
Chapter 13: Traffic and Transportation,
Chapter 14: Oil and Gas Engineering,
Chapter 15: Product Design and Industrial Engineering
目次
Preface, Committees and Sponsors
Chapter 1: Advanced Materials Engineering and Processing Technologies
An OLED Surface-Plasmon-Polariton Mode Energy Extraction Method Using a Dielectric Extraction Layer
Effect of Post Curing, Fibre Content and Resin-Hardener Mixing Ratio on the Properties of Kenaf-Aramid Hybrid Composites
Environmental Friendly Sulphoaluminate Cement Based Rapid Hardening and Repair Materials
Membrane Processing of Refined Palm Oil Wastewater Using TiO2 Entrapped Nanoporous PVDF Membrane
Discharge Criterion along the Surface of Solid Dielectric in SF6 under High Pressure
The Photodegradation Performance of Phosphotungstic Acid/CdS Composite Materials to Organic Dyes
Rigidity Analysis of Kenaf Thermoplastic Composites Using Halpin-Tsai Equation
Preparation and Characteristics of Electrospun Silver-Containing PHBV Ultrafine Fiber
Pore Size Control of Ordered Mesoporous Carbons and Adsorption Performance of Dye Molecules
Investigating the Effects of Blending Ratio and Injection Parameters on the Tensile Properties of Glass Fiber-Filled Nylon 66 Composite Gear
Polycrystalline Silicon Wafer Surface Color Defect Inspection Based on Machine Vision
Investigation into the Differences Thermal Properties of SLS Polymer Powder Materials Using Differential Scanning Calorimetry (DSC)
Preparation of High Solid Content Polyurethane Emulsion with Sulfonate Hydrophilic Chain-Extending Agents
Asbestos and Alternative Materials
Relationship between Foamability and Nanoparticle Concentration of Carbon Dioxide (CO2) Foam for Enhanced Oil Recovery (EOR)
Preparation of Hydroxyapatite Composite Coatings with Interlayer of TiO2 and its Corrosion Behaviors
Encapsulation of Multi-Enzymes on Waste Clay Material: Preparation, Characterization and Application for Tapioca Starch Hydrolysis
The Optimum Number of Trays and Solvent Circulation Rate in Removing Acid Gases in Absorption Unit
Effect of Leaching Treatment on Mechanical Properties of Natural Rubber Latex (NRL) Products Filled Modified Kaolin
Optimization of Drying and Extraction Process of Pereskia bleo Leaves in Determining Antioxidant Properties Utilizing Pareto ANOVA
Performance Evaluation of Agarwood Distillation Waste as Retarder for High Strength Oilwell Cement
Filled-NR Conductive Thin Film: A Simple Route of Graphene Dispersion in Natural Rubber Latex
A Study on Effect of PFA on Stabilized Material Using Direct Shear Test
Enhanced Thermal Conductivity of Nanofluid by Synergistic Effect of Multi-Walled Carbon Nanotubes and Fe2O3 Nanoparticles
NIR and Upconversion Luminescence Properties of Nd3+ Doped in Gd2O3-CaO-SiO2-B2O3 Glass System
To Produce Electromagnetic Shielding Material from Lignin of Black Liquor
Investigation into the Differences Chemical Properties of Laser Sintering Polymer Powders Using Fourier Transform Infrared Spectroscopy
Chiral Structure in a Hard/Soft/Hard Layered Magnet
Effect of Aging Treatment on Structural and Mechanical Properties of CuCrZr/AlN Nanocomposites
Numerical Analysis on High Speed Liquid-Solid Impact of 17-4PH Material
Gas Phase Synthesis of Vanadium Oxide Nanoparticle Films with Temperature Controlled Surface Plasmon Resonance Properties
Biodiesel Preparation with Solid Base Catalyst under Ultrasonic Assistant
Study on Microphase Separation of Waterborne Polyurethane by the Infrared Spectroscopy Peak Fitting
Electro-Reduction of Ilmenite to FexTi Alloys in Molten CaCl2
Review of Copper Atmospheric Corrosion in H2S
Optical Properties of Two Malposed Silver Triangular Nanocylinder Arrays
Study on the Optimal Proportion and Properties of Stabilized Soil Using Beach Clay
Yields Performance of Automotive Paint Sludge via Microwave Assisted Pyrolysis
Optical Characteristics of Chemically Prepared ZnO Nanostructures on Silica Modified Polyaniline Nanocomposites
Morphological and Optical Characteristics of Zinc Sulfide on Silica-Modified Polyaniline Grown on Glass and Platinum-Coated Substrates
The Use of Response Surface Methodology (RSM) in Experimental Design of Membrane Treatment in Treating PW from Oil and Gas Field
Magnetic Attenuation in Superconducting Cylinders by Beer-Lambert Modified Model
Transient AC Electro-Osmotic Flow of Generalized Maxwell Fluids through Microchannels
Tribological Properties for Cast Iron CrMo at High Temperature
Effect of Fly Ash Content on Mechanical Properties of Cement-Fly Ash Stabilized Crushed Stones
Poplar Wood Veneer Stain Retardant Study the Integration Process
The Effects of Cu Content on Microstructure and Mechanical Properties of Thixoformed A319 Aluminium Alloys
Under-Deposit Corrosion Rate Evaluation in Cooling Water System by Weight Loss, Profilometric and Electrical Resistance Methods
Effects of Curing Systems on the Strength and Microstructure of Reactive Powder Concrete with Iron Tailing Sands
Thermal Treatment Effect on Catalytic Activity of Au/TiO2 for CO Oxidation
Thermodynamic Solidification Path Assessment and Microstructural Comparison of Deep Eutectic Au-Cu-Si System
Photovoltaic Performance Improvement of Dye-Sensitized Solar Cells (DSSCs) Based on Y-Doped TiO2Thin Films
Effect of Al Addition in Cast Nickel Base Superalloy, GTD-111 on Microstructures and Oxidation Behaviors at 900 DegreesC and 1000 DegreesC
Effect of Al and Ti Additions in Cast Nickel Base Alloy, Grade Hastelloy X by Arc Melting Process on Microstructures and Oxidation Behavior at 900 DegreesC and 1000 DegreesC
A Study of Gold Recovery from E-Waste by Bioleaching Using Chromobacterium violaceum
Surface Modifications of Mg Alloys Based on Micro-Arc Oxidation Methods from Manufacturing Perspectives
Effects of Laser Cladding of Silicon Carbides Particles and Iron Based Powder
Investigation of the Thermal Properties of Different Grades Polyamide 12 (PA12) in Improving Laser Sintering Process (SLS)
Numerical Analysis for Process Parameter Effect in Electromagnetic Impact Welding of Aluminum Alloy Sheet
Synthesis of Single-Crystalline Gold Nanosheet Having Multilayer Structure under the Polymeric Bulk Condition
Design, Manufacturing and Welding of Aluminum Alloy UHV Chambers for Taiwan Photon Source
Effect of Cold Rolling Process on the Microstructure and Corrosion Behaviors of 316L Stainless Steel in Simulated Body Fluids
Steam Methane Reforming of Natural Gas with Substantial Carbon Dioxide Contents - Process Optimization for Gas-to-Liquid Applications
Preparation of Gold Nanocrystals Having Various Morphologies under Polymeric Bulk Phase
Optimization Sol Gel Process Parameter of CaCu3Mn4O12
The Technological Conception of Quality Assurance in the Surface Treatment of Aluminum and Copper Alloys
Study the Effect of Vegetable-Based Lubricant on Surface Roughness during Milling Operation by Using Response Surface Methodology
Production of Self-Healing PI Polymeric Films with Encapsulated TMPTA in PU Microparticles
Low Temperature Annealing Effect on Electrical Properties of Multicrystalline Silicon Wafers for Photovoltaic Application
Controlling the Growth of ZnO-SiO2 Nanostructures Using Pt-Coated Si Substrate
Growth of Zinc Oxide Nanostructures on Electrochemically-Etched p-Type Silicon(100) Substrate by Chemical Bath Deposition Method
The Analysis of Influence on the Edge Drop of Tandem Cold Rolling Mill
Chapter 2: General Mechanical Engineering and Applied Mechanics
A Modified EEMD Decomposition for the Detection of Rolling Bearing Faults
Research on Stochastic Resonance Method Based on Bee Colony Algorithm and its Application to Bearing Fault Diagnosis
Effects of Temperature and Volume Agglomerate Fraction on Mechanical Response of PEMFC Electrodes
Structural Optimization of the Telescopic Boom of a Certain Type of Truck-Mounted Crane
A New Plasmonic Filter through Double Metal Films Perforated with Rectangular Grooves and Circular Holes
Metallic Ellipsoidal Array - Film for Enhancing Transmission via Plasmonic Coupling
The Design of a Cylindrical Cam Structure whose Profile could be Reconstructed
Strain Measurement in the Steel Shell Surface Impacted by a Falling Ball
Analysis and Calculation of Spud Clamshell Dredger's Heeling
Dynamical Penetration Simulation of Solid Target under Shaped Charge Liner
The Study Wear Resistance of the Modified Surface of the Cutting Tool
Mechanical Effects and Existing Problems Analysis of Anchor Frame Combination Supporting Structure
The Inversion of Formation Parameters after Volume Fracturing
Multi-Pulse Chaotic Dynamics of a Composite Laminated Plate with Strong Coupling
Metallurgical Defect and Hydrogen Embrittlement Failure of a Gear
The Optimized Design of Tower Crane Hoisting System Based on the Improved Particle Swarm Optimization Algorithm
Finite Element Analysis of the Influence of Balance Mode on Rolling Mill Universal Spindle Strength
The Research on Analysis and Test Technology of Automobile Gearbox Assembly Process
Simulation Analysis and Experimental Research on Direct-Drive Wave Turbine
Pattern and Direction Based Smoothing Methods for Surfaces Modeling of Integral Impeller
Research of Wind Velocity Field of the Loading Area in Case of Empty Refrigerated Compartment of the Single Temperature Zone Refrigerator Transportation Vehicle
Slope Stability Analysis Based on Coupling Multiple Factors
Simulation Research on Rolling Element Bearing Feature Extraction Based on Recursive Least-Squares Lattice-Ladder Algorithms
Comparison of Suppression Cavitations Schemes within Hydraulic Valve
Investigation into the Polishing of Stainless Steel Using Sisal Wheels
Effect of Process Parameters on Surface Roughness in the Cloth Wheel Polishing of Stainless Steel
Automatic Wiper System Based on the Adjacent Capacitive Edge Effect
Effects of Flap Wheel Grinding Parameters on Surface Roughness for Stainless Steel
Experimental Investigation on Axially Loaded PFRP Compression Members Having Double C-Sections
Modeling and Simulation of Railway Vehicle Using ADAMS/Rail
Reynolds Number Effect Investigation of Shock Wave on Supercritical Airfoil
Undersea Observatory Platform Shape Design and Sinking Calculation Based on Fluent
Nonlinear Analysis of Stochastic Heave Motion for Truss Spar
Analytical Investigation on Optimum Member Angle of Lattice Truss Structures
Research on the Effect of Prefabricated Crack Distribution about Crack Propagation
Water Desalination System: Experimental Study on the Performance of a Multi-Stage Still
Analysis of Factors influencing Galvanized Sheet Friction based on Orthogonal Experiments
Chapter 3: Applied Thermodynamics, Heat Transfer, Energy Conversion
Experimental Study on Thermal Effect of Shear Strength of Cohesive Soil
Investigation and Analysis on Energy-Saving Status in Building Lighting in China, Japan and Korea
Using MATLAB and COMSOL Multiphysics for Optimization of the Model of Underground Thermal Processes at Old Mining Dumps
Analysis of Temperature and Heat Flow Characteristics in Underground Tunnel
The Experimental Study on the Effects of Supply Air Angle on Indoor Thermal Environment
Application of Water-Intake Methods on Open-Loop Surface Water Source Heat Pump
Introduction of Respirable Air Conditioner Based on the Principle of Gravity Circulation
Heat Transfer Analysis of Groundwater Flow for Ground Heat Exchangers in the Multi-Borehole Field of Ground Source Heat Pump under the Intermittent Operation
Numerical Modeling of the Flow and Pollutant Dispersion in Street Canyons with Ground Thermal Effect
Thermodynamic Effects on Hydrate Formation in Deepwater Pipeline
The Tilt Angle of the Solar Panels has the Highest Power
Empirical Analysis on Peasant Households' Willingness of Using Solid Biomass Fuel
Theoretical Investigation on Electron Transport and the Effect on Thermal Transport in Graphene Ribbon
The Experimental Study of Floor Heating for Solar House
Chapter 4: Instrumentation, Measurement Technologies, Analysis and Methodology
A Novel Change Detection Method Using Independent Component Analysis and Oriented-Object Method
Visual Pop-Can Detection Method Based on AdaBoost
Research on Method of Metro Monitoring Model Based on Grey Prediction Algorithm
The Numerical Simulation of Underwater Electric Field Sensor Calibration Traceability
A Numerical Simulation of VOCs Distribution in Indoor Environment of a Dormitory
A Current Harmonic Detection Method via Input Observer
A New Method of Continuous Blood Pressure Measurement Based on the Pulse Image Sensor
Experimental Study on Measuring the Steel Stress via FBG Sensors
Design and Simulation of Polarized Neutron Reflectometry at CARR
Numerical Simulation of Fractured Rock Slope with Shear-Slip Behavior
Characterization of Heavy Metal Contaminated Wastewater Using a Coaxial Sensor and Electromagnetic Wave Reflection Technique
Development of a Railway Track Displacement Monitoring by Using Digital Image Correlation Technique
Research on Underwater Binocular Camera Calibration and Distortion Analysis in Current Disturbance
Video Copy Detection Based on Principal Component Analysis
Bearing Damage Detection Based on Sound Signal
Tool Fault Analysis with Decision Tree Induction and Sequence Mining
Alternative Working Electrode for the Determination of the AntioxidantContent by Electrochemical Techniques
Chapter 5: Electronics and Integrated Circuits, Embedded Technology and Applications
Model Reduction and Controller Design of a DC-DC Converter
An Automated-Switching Precision Decade Capacitor
Influence of Inhomogeneous Anisotropic Ground Conductivity upon the Directivity of ELF Line-Current Antenna
The Fully Digital Controlled Corrector Magnet Power Converter with a Shunt as a Current Sensing Component
Radio Telemetry Unit for Online Monitoring System at Mining Dumps
The Wireless Sensor System Based on the Chip of STM32 and SH79F32
Data Acquisition and Wireless Data Transmission of Lightning Electromagnetic Field
Signal Integrity Analysis of High-Speed Differential Vias
Investigation of Melting Current in Glass Tube Fuses
An Optimized Combination of Frequency Domain Adaptive Equalizers
The Impedance Characteristics of ELF Line-Current Antenna over Inhomogeneous Anisotropic Ground
Star-L-Shaped Circularly Polarized Ultra-Wideband Microstrip Antenna for Wireless Applications
Multiband Antenna Formed of Superimposed Compressed Loops
Hardware Implementation of Modeling Frequency Coded Serial Communication for Eurobalise Using ASK Module
Chapter 6: Electrical Engineering and Electric Machines
Research on Inverse Form Innovation Design for ATSE with Dual Power Supply
Proposed Control Method of Doubly Fed Induction Generator Rotor Side Converter Based on System Frequency Regulation
A Modeling and Simulation Method for SVPWM
Modeling and Simulation of Improved Vector Control System for PMSM
Design of Horizontally Vibrating Linear Motor for Thin Smart Phone
A Model Predictive Control Method for Bidirectional DC-DC Converter in the ZVS Condition
Study on Problem of Sensorless PMSM Parameters Identification
Research on Optimization Design of Low-Voltage Circuit Breaker Power System
Chapter 7: Power System and Energy Engineering, its Applications
Analysis of the Characteristics of PMSG Tidal Current Power Generation System Using PMSG and Water Tunnel
Fault Diagnosis Method for Power Network Based on Combinational Cross Entropy Algorithm
Effect of Contacting Air Surface of Cathode on Microbial Fuel Cells
Trust and Power Factor Regulation Based Power Control Scheme for High Penetration Photovoltaic
Wartime Nuclear Power Plant Security Protection Research
The Research on the Design Method of Micro Grid Operation Control Strategy Based on the Analysis of the Typical Example
Design of an Intelligent Solar-LED Streetlight
The Effect of Power Supply of LED Lamp
Research of Rough Set Theory on Forecast of Power Generation for Grid-Connected Photovoltaic System
A Novel Sliding Mode Control Based Low Voltage Ride through Strategy for Wind Turbine
Rotation Energy Harvesting Device
A Suitable Method of Energy Storage Capacity Optimization Based on DFT for BIPV
Modeling of Water Removal from PEM Fuel Cell during Gas Purging
Chapter 8: Mechatronics and Robotics
Intelligent Control System Design of a Unmanned Quadrotor Robot
A Mobile Robot Obstacle Avoidance Using Fuzzy Logic and Model Predictive Control
Development of a Force Feedback System for Omni-Directional Telepresence Robot
Intelligence Dumping into Autonomous Robotic Systems for Higher Autonomy
A New Approach for Face Recognition Performance Evaluation for Robot Using LED Monitor
Actuation by Pneumatic Muscles of a Parallel Asymmetric Gripper System
Dynamic Response of Commuter Rail Vehicle under Lateral Track Irregularity
A Simulation of the Number of Particles Trapped by the Circulating Filter of a Hard Disk Drive and their Trajectories
FEM Analysis for the Influence of Manufacturing Process Defects on Dynamic Behavior of Thin Chromium Microbeam
A Study on the Key Technologies of a Kind of Automatic Packaging System
Research on the Key Issues of Numerical Controlled Machine Layout Design
Chapter 9: Control and Automation of Manufacturing
PI Control of Proportional Valve-Cylinder Water Hydraulic System
Two Types of Neural Network Prediction Models and Time Complexity
Design and Simulation of Automatic Control System for Feed-Drier
The PWM Rectification System Based on Intelligent PI Controller
Design of Automation Control System for Lubricant Syringe
Design of Auto Lifting Control System Based on PLC
Oscillation of Second-Order Nonlinear Differential Equations
Organize Method on Platform of Machine Automation Control System
The Optimal Control Strategy of Frequency Carrier Intelligent Shutoff
Study on Hydraulic System of Test Stand for Subsea Control Module
Application of Genetic Programming Method Combined with Neural Network in HVAC Optimal Operation
The Design and Research of Automatic Control Feeding System
Multi-Processing Feed-Back Decision Making for Scheduling Gates in Manufacturing System
Optimal Sequence-Dependent Job Scheduling of Packing Process with Multiple Non-Identical Machines in Tablet Production
Chapter 10: Signal and Image Processing, Data Mining and Computational Mathematics
Inverse Kinematics of NAO's Right Arm towards its Handwriting a Chinese Character Based on Corner Detection of Character Template
A New Method of Parameters Determined in PCNN
A Promotion of a Color Morphological Filter
An Improved Filtering Algorithm for Impulse Noise with High Density Based on Edge Information Preservation
Image Copy Detection Based on DCT Ordinal and Block Median
The Blind Watermarking Method Simulation Research Based on Wavelet Tree Quantization
Research of Signal Processing Based on Kalman Filter and Particle Filter
A Frequency Reuse Scheme Based on Interference Pre-Cancellation and Resource Scheduling for Multi-Beam Satellite Downlink Signal
Quality Control Oriented Data Analysis and Application of Traditional Chinese Medicine Extraction Process
Driver Fatigue Monitoring Based on Head and Facial Features Using Hierarchical Bayesian Method
The Application Research of Data Mining in Research-Oriented Learning Platform Building
Improved Relative Term Frequency Probability Feature Selection for Document Categorization
Facial Expression Recognition Based on the Texture Features of Global Principal Component and Local Boundary
Mixed Expression Recognition & Analysis Based on Compressed Sense and Subjection Degree
NURBS Curve Extraction from 2D Laser Sensor Data and 3D Simulated Data
A New Method for Processing Symbolization Time Series
Comparison Study of the Clustering Analysis Methods in the Load Time-Variation Research
Study on Wavelet De-Noising of High Frequency Current Signal for Rotor Position Self-Sensing of PMSM
The Use of OpenMP Parallel Standards in Massive Data Delaunay Triangulation
Approaches in Pattern Recognition and Classification Based on Coin Images
Global Color Composition for Curved Screen Display System
An Iterative Indexing PLANO Frame Work for Graph Feature Mining
Wideband LFM Signal Parameter Estimation Based on Compressed Sensing Theory
Hybrid Radio and Visible Light Communications in Inter-Vehicle Communication
Research of the Transient Signal Recognition Based on Empirical Mode Decomposition
An Improved Normalized Cut Image Segmentation Algorithm with k-Means Cluster
Object Update-Based Mean Shift Tracing Algorithm Combined with LBP
Application of Kalman Filtering and Smoothing for Airborne Gravimetry
Exact Soliton Solutions of the Variable Coefficient KdV Equation with Forced Term
Predicting BEOL Key Qualities by Mahalanobis-Taguchi System - An Example of Taiwan's Semiconductor
Solution of Travelling Salesman Problem Using Ant Colony Algorithm
Research on Application of Ant Colony Optimization
Application of Ant Colony Algorithm
Optimization and Simulation of OFDM System Based on Orthogonal Wavelet
Joint Multiple-Access Channel Effective Order and CIR Estimation Algorithm for Multi-User OFDM/SDMA System
Adaptive Equalizer for DS-CDMA Multi-User Communication System Using Sign-Algorithm Based on Laguerre Filter Structure
Wind Speed Prediction Based on Improved Grey Neural Network Model
The Automata Model of Interval Speed CPNs
Multi-Level Indicators Reduction Approach for Complex Index System
Numerical Simulation of Droplet Ejection Based on VOF Method
Analysis of HCV's Linearity Using Support Vector Machine (SVM)
Chapter 11: Communication, Networks and Information Technologies
Information Extraction of Pro/E Swept Features Based on Pro/Toolkit
An Optimization Model and Genetic Algorithm Solution for Automated Celestial Navigation of Ships
A Multi-Band Carrier Aggregation Scheme for Mobile Satellite Communications
Access Control Algorithm with Limited Power Constraint for Mobile Satellite Communications
A Method of Interface between Matlab PV Model and PSASP Transient Stability Program
TCP Communications Research Based on Embedded WinCE and LabVIEW
Studying the Impact of 32-Bits AS Numbers on Constructing Internet AS Graphs
A New Intrusion Detection Method Based on Machine Learning in Mobile Ad Hoc NETwork
Study on High-Performance Simulation Computer for Large-Scale System of Systems Simulation
Investigating the Effect of Software Complexity Metrics on Software Cost
A Design for Fault-Tolerant Communication Middleware Based on Time-Triggered
Design of Theme Crawler for Web Forum
Design and Implementation of the Network Electronic Identity Management System
Development of Bluetooth Roll Call System Based on Android Platform
On the Construction of Efficient Private Signature Scheme
Alternative Antenna Research to Optimize MIL-STD-188-125-1 Standard Shielding Effectiveness Measurement
A Modified Energy Detection Algorithm Based on Primary User Activity for Cognitive Radio Networks
Joint Transmit Antenna Selection and User Selection in Cognitive Radio MIMO Systems
A Velocity and Transmission Environment Based Handover Algorithm for Heterogeneous Networks
Joint Linear Precoding and Power Allocation for MU-MIMO CR Systems with Imperfect CSI
Partial Interference Alignment Schemes for the K-User MIMO Interference Channel
The Design of Android-Based Video-on-Demand System and its Implementation
The Method for Broadband Folded Dipoles Using Branch Current Redistribution
Design of a Smart Antenna Using Butler Matrix for WLAN Applications
A Novel Coverage Off-Duty Eligibility Rule in Wireless Sensor Networks
An Effective Improved On-Demand Routing for LEO Satellite Networks
Design of IOT Gateway System Based on WMMP-T Protocol
Design of Wireless Voice Communication System in Underground Coal Mine Based on ZigBee
Study on WSN Localization Algorithm and Simulation Model for Intelligent Transportation System
Research on Particle Swarm Optimization-Based Node Positioning Algorithm for Wireless Sensor Networks
Improved Clipping Technique for PAPR Reduction in OFDM
A Non-Uniform Node Distribution Policy for Routing Holes Avoidance
An Item-Level Access Control Framework for Inter-System Security in the Internet of Things
Preliminary Study on Collaborative Lesson Planning Based on Cloud Platform
Management of Big Data in the Internet of Things in Agriculture Based on Cloud Computing
A Fine-Grain Price Analysis for Online Transaction Data
Research and Design of Web-Based Autonomous and Collaborative Teaching Mode under Blended Learning
Control of Synchronization on Community Networks
Responsive Web Design for Mobile Device Screen Optimization
Solving Bottleneck Problem by Transmission Power Control under Various Compression Assumptions for Wireless Sensor Networks
A Group Persistent Assignment in Contention Slots of DOCSIS
Calculating the Reliability and Reputation of Agents in E-Commerce Multi-Agent Environments
Mathematical Programming Models for Flexible Manufacturing System Planning and Scheduling Problem
Study on Water Conservancy Information System Based on Cloud Computing
Proposed System Model for Android Augmented Reality System in Malaysia Military Operations - Unit Positions
A Development of Next-Generation Port Simulator for the Performance Evaluation of Port Crane
Dynamic Federal Collaborative Development Method for Heavy Military Vehicles
An Empirical Research on E-Marketplace Basic Functions
Adaptive H Power and Rate Control for Time-Varying Uncertain Wireless Networks via Dynamic Output Feedback
A Neural-Q-Learning Based Approach for Delay Tolerant Underwater Acoustic Wireless Sensor Networks
Research and Application of Information Management for NC Equipment
A Level-Dependence Model and it's Application in SFMEA
Information Processing in Searching Tweets
A Research of HTN-Based Anytime Planning Algorithm on FPS Games
A MapReduce Model to Process Massive Switching Center Data Set
Pixel Value Graphical Password Scheme: Identifying Design Features and Requirements
Study on the Multi-Layer Structure Design of the Power Marketing Demand Side Monitoring Center System
Modeling and Simulation of Indoor Millimeter Wave Propagation Characteristics
Chapter 12: New Technologies, Methods and Technique in Civil Engineering
Numerical Simulation of Dynamic Compaction Construction
Integrated Model for MCDM: Selection Contractor in Malaysian Construction Industry
Surface Quality of Actual Structure with Concrete Using Expansive Additives
Design Guidelines for Buildings in Saudi Arabia Considering Energy Conservation Requirements
Vibration Response Analysis on Deep-Water Piers under Earthquake and Wave Coupling Motivation
The Fuzzy Evaluation of Compatibility between PC-HPWR Agent and Cement
The Bionic Optimization and Analysis and Calculation of the Cast-Steel Joint with Three Branches
Measurement and Analysis of the Structural Noise of Urban Bridges
Architecture and Paper Structures - Could Paper-Folding Become a Methodology in Architecture?
Optimization Design Study on Uniform Air of Structure of the Cavity Plenum of Badminton Gymnasium
Review on the Study of Green Design Performance for Building Refurbishment Project: Finding the Gaps in Knowledge
Risk Management of Construction Schedule by PERT with Monte Carlo Simulation
Review of Durability of Fiber Reinforced Polymer (FRP) Reinforced Concrete Structure
Research on the Waterproof Properties of Lightweight Gypsum Materials
Effect and Action Mechanism of Superplasticizer on Foamed Cement
Effect of Admixtures on the Performance of Recycled Fine Aggregate Cement Mortar
Research on the Wall Crack Grouting Technology of Brick-Concrete Structure
Based on ANASYS Immersed Tube Tunnel Three-Dimensional Finite Element Analysis
Occurrence Analysis of Cracking Concrete Floor Caused by Alkali-Aggregate Reaction
Numerical Analysis on the Impact of Windows and Interior Doors on Indoor Airflow of Rural Residence
Exploration for the Technology of Tradition Building Materials and Consolidation Mechanism
Introduction to the Urban Space Stereo Greening
Simulation Analysis of Building Green Facade Eco-Effect
CFD Investigation for Indoor Environment of a District Standard Room in Jinan City
Low Cycle Test Research on Seismic Performance of Recycled Concrete Block Wall
Micro-Analysis Ballast-Geogrid Pull out Tests Interaction
The Evaluation Method for Tunnel Structure Health Condition Based on Asymmetric Proximity
Identification of Transverse Crack in Beam like Structure Using PSO
Comparison of Several Extreme Learning Machine Algorithm for Modeling Concrete Compressive Strength
The Numerical Simulation and Research and Application of Energy-Saving Effect of Air Curtain of the Dining Room
Research on Cracks Zone of Clay Aquiclude in Overburden
Construction Numerical Simulation of Cable-Supported Barrel Shell Structure Considering Construction Nonlinearity
Wind-Induced Performance of Long-Span Bridge with Modified Cross-Section Profiles by Stochastic Traffic
Analyses on the BIM Technology Using in the Design of Green Village Buildings
Numerical Simulation on Embedded Steel Frame Concrete Blast Wall Resisting Air Shock Wave
The Construction of Modern Residences Based on the Concept of "Ecological" Green Community
Study on Green City Construction and Sustainable Development - Low Carbon City from Theory to Create
Research on Slow Lane System Planning and Design: A Case Study of Guangzhou International Biological Island Greenway
Establishment and Solution of the RNC Flow Network Model
Research on Detail-Structure Construction Technology of Outside Heat Preservation of Exterior Walls
A Validation Study for CFD Simulation of a Simplified Urban Model
Real-Time Simulation of Pipe Network Based on EPANET
Application of Vertical Planting Technology in Green Building
A Research on Key Technology in Overturn-Preventing of Longxi Tower's Monolithic Movement
Application of Green Lighting Technology in Highway Service - A Case Study of Mt. Lushan West Sea Tourism Highway Service
Chapter 13: Traffic and Transportation
Evaluation for the Location Selection of Airport Based on WLSM-TOPSIS Method
Research on the Calculating Method of Low-Carbon City Public Transit Bearing Rate
Study on the Scheme Selection of Large-Scale Highway Transportation
The Laws and Measurements Analysis about Urban Rail Transit Noise and Vibration Reduction
The City Traffic Service Platform Based on MPI Model
The Simulation of Non-Gaussian Vibration Environment on Railway
Research of a MapReduce Model to Process the Traffic Big Data
Application of Multidimensional Data Model in the Traffic Accident Data Warehouse
A Study of the Traffic Flow Predictive Model Based on Mathematical Statistics and Stochastic Process
Chapter 14: Oil and Gas Engineering
Effective Bridging Agent Particle Sizes of Reservoir Drilling Mud
Carbon Dioxide (CO2) Foam Stability Dependence on Nanoparticle Concentration for Enhanced Oil Recovery (EOR)
Determination of Irreducible Water Saturation and its Application in Analysing Water Producing after Fracturing
Calculation Method of Earth Stress in Zhenjing Oil Fileld in China
Numerical Coupling of Drilling Vibration to Riser's Oscillation
Chapter 15: Product Design and Industrial Engineering
Improving the Design of Peripheral IV Therapy by Employing Product Development Approach and Rapid Prototyping Technology
-SVR-Based Predictive Models of Energy Consumption and Performance for Sintering
Application of Variation Weight Fuzzy Comprehensive Evaluation Method on Decision-Making of Stamping Process
Research on the Methods of Integrated Implementation of ERP and BPR
Kansei Quality Prediction Method of Product Form Design Based on Quantification Theory
A Heuristic Approach to Capacity Assignment in Pharmaceutical Manufacturing Production Line
Product Maturity-Driven Collaborative Development Flow Controlling Method for Heavy Military Vehicles
Risk Analysis in Military Operation Network Effectiveness Evaluation
Sensory Fuzzy Evaluation System Applied in the Cabs of Mine Vehicles
Study on the Pharmaceutical Distribution Enterprise IT Adoption Influencing Factors Model
The Use of Interval Type-2 Fuzzy TOPSIS in Supplier Selection
A Novel Integrated AHP-QFD Model for Investment Banks
Network-Fit in a Disruptive Environment: Assessment of the Strategic Fit among Partners of a Value-Added Network
An Empirical Study of Perceptual Factors Underlying Customer Reactions for New Product Positioning in Notebook Industry
Analysis on Convergence in Green Technology Field Using Patent Information
Enterprise Logistics System and Simulation Control Technology
Integrated TRIZ-AHP Support System for Conceptual Design
「Nielsen BookData」 より
