Development of applied engineering sciences : selected, peer reviewed papers from the 2014 5th International Conference on Computing, Control and Industrial Engineering (CCIE 2014), October 25-26, 2014, Wuhan, Hubei, China
著者
書誌事項
Development of applied engineering sciences : selected, peer reviewed papers from the 2014 5th International Conference on Computing, Control and Industrial Engineering (CCIE 2014), October 25-26, 2014, Wuhan, Hubei, China
（Advanced materials research, v. 1037）
Trans Tech Publications, c2014
- : pbk
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the 2014 5th International Conference on Computing, Control and Industrial Engineering (CCIE 2014), October 25-26, 2014, Wuhan, Hubei, China.
The 122 papers are grouped as follows:
Chapter 1: Applied Material Science,
Chapter 2: Engineering Solutions and Designing in Machinery,
Chapter 3: Technologies and Tools of Measurements, Detection and Diagnosis,
Chapter 4: Mechatronics, Control and Automation,
Chapter 5: Applied Computational Procedure and Algorithms in Engineering Practice,
Chapter 6: Applied Information Technologies in Design and Research,
Chapter 7: Engineering Provision and Production Management.
目次
Preface, Committees and Sponsors
Chapter 1: Applied Material Science
Analysis about Drawing Broken of SWRH 72A High Carbon Steel
Flexible Rolling Technology of Spring Steel 60Si2Mn
The Effects of Ultrasonic Wave on the Properties of Flax Fiber Treated in Alkali
Study on Damage Tolerance of Composite Laminates with Hole or Crack
New Optical Sensor Panel on Nanocomposite Base
Research on Prediction Model of End Sulfur Content for Converter Smelting
Chapter 2: Engineering Solutions and Designing in Machinery
Research on the Virtual Prototype of Multifunction Filter Material Detection Device
Wave Spring Dynamic Characteristics Analysis
Characteristic Analysis and Optimization for the Tailstock Body of the NC Lathe
The Design of Climbing Rod Car
Hydraulic Excavator Working Device Simulation Based on Virtual Prototype
Hysteresis Modeling and Analysis for Dynamic Compaction
Dielectric Barrier Discharge Structure Design for Sewage Treatment
The Influence of Payload Mass and Inertia Properties on a Piloted Flight Simulator Hexapod Dynamic Performance
Simulation Analysis on Hobbing Process and Heat Treatment of Automotive Transmission Gear Based on the MASTA Software
Dynamic Modeling of an Independent Wheelset Bogie with MapleSim
The Structural Optimization of Large Capacity Skip Based on ANSYS
Establish the Model of Parameters Optimization of Sheet Metal Forming in Drawing Process Based on Artificial Neural Network
Reliability Assessment for Axle Box Spring of EMU Based on the Actual Operation Data
The Research of Manufacturing Technique about Intertwined Stator Core in Automotive Alternator
Research on Mobile Mechanical Products of Recycling Method
The Design of the Rolling-Shoe Bearing Device Based on Rotary Cylinder
Based on Moldflow Automobile Light Lens Mold Develop and Application
Liquid-Solid Hydrocyclone Numerical Simulation and Separation Efficiency Analysis
Study on Walking System Technology of Crawler Combine Harvester
Application of TRIZ Substance-Field Analysis Model in Equipment's Combat Resilience Design
New Thermal Energy Converters Based on Polyelectrolyte Hydrogels
Chapter 3: Technologies and Tools of Measurements, Detection and Diagnosis
The Reciprocating Compressor Fault Analysis Based on ORSGWT
Design and Experiment of Fumigant Gas Trace Detection System Based on Photoionization
Design the Integrated Multipurpose Instrument Calibrating Equipment Based on the PXI and LabVIEW
Research on Crab Bucket's Drift Angle Detector
A Temperature Measurement Method Based on RC Discharge Circuit Using Platinum Resistance
Fuzzy Diagnosis Method of Aero-Engine Fault
A Security UV Curing Device Based on LED Array
A Kind of Resistance Capacitance Measurement Method Based on Time Constant
The Design of Virtual Experiment Framework Based on ELVIS
Design of Examination and Adjustment Instrument of Artillery Zero Line Base on Laser Technique
Research on Gate Valve Internal Leakage Detection Based on Acoustic Emission Signal Processing
Design and Implementation of Portable Test Diagnosis Instrument for a Type of Electronic Equipment
A Novel Method for Measuring the Evenness of Raw Silk
Study on Detection of Black Field and Static Frame in IPTV and Mobile TV's Quality Supervision
A Research about Acquisition and Transmission of the Water Meter's Image Based on STM32
Chapter 4: Mechatronics, Control and Automation
Design of Civil Aircraft Avionics System Bus Excitation System
Reliability Assessment Based on Performance Parameter for Micro-Gyro
Complex Wireless Sensor Network Routing Strategy for Information Rapid Transmission
Research on Solving the Watertightness Problem of Underwater Angular Sensor Driven by New Magnetism
The Design of Kiln Liquid Level Control System with Long Time-Delay
Simulation Analysis on Hydrostatic Transmission Based on the MATLAB/SIMULINK
Efficiency Analysis on Hydro-Mechanical Transmission
Design of LQR Controller for the Inverted Pendulum
Study on Auto-Tuning PID Controller
Wheeled Robot Path Tracking Study Based on IMM Algorithm
Design of Vehicle-Mounted Solar Photovoltaic Panels System that Change Orientation with the Light
The Application of Artificial Intelligence Technology in the Selective Laster Sintering
The Roller Speed Control of High Voltage Electrostatic Separator Based on PLC
Power and Vibration of Electrostatic Precipitator Control Based on FPGA
A Fuzzy Predictive Controlling Method of Fermentation Tank Temperature
Research on the Modeling of Hydraulic Turbine Governing System
Nonlinear Internal Model Control for Bearingless Induction Motor Based on Inverse System Theory
Paralleling Hydraulic Control of Variable Frequency Motor and Valve for the Swing Mechanism of Segment Erector
Design of Testing & Identification System for Recovery Material of Launch Control Device of Certain Missile
Research on Oil Temperature Control Technology of Mobile Machinery in Closed Hydraulic Transmission System
Design of Equipment Power Remote Control System Based on Ethernet
Post Processing for Five-Axis Machine Tools with Pose Error Compensation
The System Identification Analysis of the Rolling Motion Model for the Unmanned Boat
Digital Controller Design Research Based on Series Compensation
Design of a Switching Power Supply for Wheelchair Controller Based on Magnetic Isolation Technology
Study of a Super-High-Speed PMSM Drive with Low Eddy Current Loss
Development of the HWIL Training Simulator of UAV Engine
Based on ARM of AC LED Intelligent Lighting System Design
Design of Equalizer Circuit for Lithium-Ion Batteries in Mine-Used Lifesaving Cabin
Optimization Algorithm of Real-Timing Signal Control for Isolated Intersections
On Emergency Response of Swarm Robotics for Chemical Hazards
Design of OPC Client Based on .NET for Advanced Control System
The Design of Control System for Sewage Treatment Based on PLC
Chapter 5: Applied Computational Procedure and Algorithms in Engineering Practice
The Pattern Recognition Method for Wear Particle Image Based on Rough Sets - Neural Network Theory
Online Forecasting and Calculating of Steam Turbine Exhaust Enthalpy Based on RBF Process Neural Network with Two Hidden Layers
Applied Research of Ant Colony Algorithm in Fault Diagnosis
Dual Objective Multidimensional Parameter Optimization of Cam Curve Based on Improved Ant Colony Algorithm
Layout Optimization for Deformable Trimaran Based on BP Neural Network
Research of the Interpolation Method Applied to the Numerical Simulation of the Casting Filling Process
Robust Inland Waterway Ship Tracking via Hybrid TLD and Kalman Filter
A Simaplied Adaptive Kalman Filtering Algorithm
A Scalable D Dominant Strategy to Solve Large-Dimensional Multi-Objective Optimization Problems
Using the Improved Genetic BP Neural Network Algorithm for Lithologic Identification
Applications of Color Morphology in Image Denoising
A Hierarchical Feature Selection Method Based on Classification Tree for HGU Fault Diagnosis
BP Neural Network Based Optimization for China Railway Freight Transport Network
A Novel Extracting Algorithm of the Low Gray Fuzzy Edges for Infrared Images
A Fast Target Searching and Capturing Method for Phased Array Radar
Parameters Selection of LLE Algorithm for Classification Tasks
Informo-Dynamics Functionals in the Study of Fields of Anisotropy of a Microrelief Spinning Tapes
Chapter 6: Applied Information Technologies in Design and Research
Design of Interlnk Protocol Packet at Embedded Linux
Research on the Loading Pattern of Embedded System
The Study of the Trust Mechanism Based on Mobile Agent in the E-Commerce Agricultural Commodity Trade
Research of the Technology and Application of Process Digital Mock-Up for Spacecraft Assembly Based on the MBD
Research on Virtual Real-Time Simulation System Based on EON
Design for Virtual Laboratory of Mechanical Drawing on Web
Development and Application of CAD Technology
Research on Key Technologies for Construction of Three-Dimensional Machining Procedure Model Based Definition
Development and Application of CAD Technology in Railway Vehicle Studying
A Novel USB3.0 High Definition 3D Video Camera Based on ARM
Chapter 7: Engineering Provision and Production Management
Study on Novice Drivers' Fixation Features under Different Car-Following Risk Levels
Group Technology Applied in Quality Management System
Possibility Theory on Economic Problems
Knowledge Management for Product Development: A Review
Research on Production Schedule Online Processing Management of Sand Casting Workshop Based on Single Piece Management Model
Quantum Evolutionary Algorithm for Chemical Batch Scheduling Problem
Particle Swarm Optimization for Chemical Multi-Stage and Parallel Batch Scheduling
Heuristic Particle Swarm Optimization for Scheduling Chemical Flowshop with Limited Intermediate Product Storage
Extracting Cognitive Maps for Intelligent Conceptual Product Design
The Ordering Strategy of ES Model and Option Contract
A Method for Air Material Failure Prediction Based on Weibull Analysis
Development and Application of the Performance Evaluation System for Integrated Supply Chain
Activation Factors and Sliding Mechanism of Ancient Landslide in Huale Coal Mine
Study on the Development Model of Green Products Based on Concurrent Engineering
To Analyse the Timely Maintenance System Usability by Stochastic Process
Risk Analysis about Operation of UHV Power Grid Operation and Maintenance Based on Security Benchmarks
Simulation and Optimization of Productive Process of Titanium Sponge
Application of RFID in a Flexible Assembly Production Line Based on Tracking Algorithm
Information Application of Production Line in the New Energy Automobile Based on RFID
Research on the Harm Mechanism and Related Standards of Children's Toys
「Nielsen BookData」 より
