Engineering and innovative materials III : selected, peer reviewed papers from the 2014 3rd International Conference on Engineering and Innovative Materials (ICEIM 2014), September 4-5, 2014, Kuala Lumpur, Malaysia
著者
書誌事項
Engineering and innovative materials III : selected, peer reviewed papers from the 2014 3rd International Conference on Engineering and Innovative Materials (ICEIM 2014), September 4-5, 2014, Kuala Lumpur, Malaysia
（Advanced materials research, v. 1043）
Trans Tech Publications, c2014
- : pbk
大学図書館所蔵 件 / 全1件
-
該当する所蔵館はありません
- すべての絞り込み条件を解除する
注記
Includes bibliographical references and indexes
内容説明・目次
内容説明
Collection of selected, peer reviewed papers from the 2014 3rd International Conference on Engineering and Innovative Materials (ICEIM 2014), September 4-5, 2014, Kuala Lumpur, Malaysia.
The 54 papers are grouped as follows:
Chapter 1: Structure and Properties of Materials;
Chapter 2: Research and Development of Technologies of Synthesis and Processing of Materials;
Chapter 3: Environmental Chemistry and Practice of Using the Nature Materials;
Chapter 4: Machinery in Area of Manufacturing and Processing of Materials, Construction Technologies and Materials
目次
Preface and Committees
Chapter 1: Structure and Properties of Materials
Nano-Yttrium Aluminium Garnet Interfacial Tension and Viscosity for Enhanced Oil Recovery
A Study of LiMn(2-X)FexO4 Cathodic Nano Material for Lithium-Ion Batteries
Effect of Cell Material on the Performance of PV System
The Influence of Carbon Addition on Microstructure and Mechanical Properties of Fe-22.0Al-5.0Ti Alloy
Zinc Oxide Nanostructures Formed by Wet Oxidation of Zn Foil
Effect of CNT Arrays on Electrical and Thermal Conductivity of Epoxy Resins
Investigation on Microstructure and Mechanical Properties of Squeeze Cast Al-Si Alloys by Numerical Simulation
FTIR and Electrical Studies of Hexanoyl Chitosan-Based Nanocomposite Polymer Electrolytes
In2O3-Based Thin Films Deposited by Spray Pyrolysis as Promising Thermoelectric Material
Solid Particle Erosion Behaviour of Martensitic and Nitrogen Alloyed Austenitic Stainless Steel
Porous GaN for Gas Sensing Application
Diode Parameters of Heterojunctions Comprising p-Type Si Substrate and n-Type -FeSi2 Thin Films
Chapter 2: Research and Development of Technologies of Synthesis and Processing of Materials
Optimization of Multi-Pass Pocket Milling Parameter Using Ant Colony Optimization
Investigation of Carbon Nanofiber Supported Iron Catalyst Preparation by Deposition Precipitation
Hydrophobic-Synthesis of Bio-Based Epoxy Substrate Using Methyl Ester and its Dust Deposition and Decontamination Effects
Synthesis and Characterization of Octaethoxycalix[4]Arene for Heavy Metal Cations Adsorbent
Recycling of Pre-Fabricated Carbon-Fiber Waste as Filler for Sandwich Glass-Fiber Auto Parts
Prediction of Friction Stir Processed AZ31 Magnesium Alloy Micro-Hardness Using Artificial Neural Networks
Fabrication of ZnO Nanorod for Room Temperature NO Gas Sensor
Synthesis of Co/CNTs via Strong Electrostatic Adsorption: Effect of Metal Loading
Water Dispersion Conductive Polypyrrole Based on Nanocrystalline Cellulose
Electroless Deposition of Silver Nanoparticles and Nanowires in Ethylene Glycol
Electroless Deposition of Copper Nanostructures in Aqueous Solution
Finite Element Study of Deformation Behaviour of Al-6063 Alloy Developed by Equal Channel Angular Extrusion
Electrochemical Characteristics of an Optimized Ni-P-Zn Electroless Composite Coating
Synthesis of C-2-Ethoxycarbonylmethoxyphenyl Calix[4]Resorcinarene Using Salicylaldehyde as Basic Material and its Application as Adsorbent of Pb(II) Metal Cation
Simulating of Backward Extrusion Process of Nanostructured Al-6082 Material
Glass Ceramization as an Alternative Production Route of Forsterite Glass-Ceramics for Possible Multipurpose Uses
Relative Effect of Sand Blasting and Acid Etching on the Surface Roughness of Pure Titanium and Titanium Alloy for Dental Implants
The Breakdown of Carbide Network in a H23 Tool Steel by Hot Axisymmetric Compression
Cementite Precipitation of a H21 Tool Steel after Hot Compression and Double Temper
Solidification Behaviour of a H21 Tool Steel
Experimental Investigation of Effect of Rotary Abrasive Jet Nozzle on Coating Removal Rate and Surface Finish
Chapter 3: Environmental Chemistry and Practice of Using the Nature Materials
Methane Adsorption on Chemically Modified Microwave Irradiated Palm Shell Porous Carbon
Biopulping by Ceriporiopsis subvermispora towards Pineapple Leaf Fiber (PALF) Paper Properties
Hydrophobicity Characterization of Bio-Wax Derived from Taro Leaf for Surface Coating Applications
In Situ Deposition of Conducting Polymer onto Pineapple Leaf Fiber
Characteristics of Potassium Acetate - Activated Coconut Shell Carbon
Synthesis of Zeolite A from Coal Fly Ash by Alkali Fusion and Hydrothermal
Mangrove Tannin (Rhizophora apiculata) Complexes with Copper (II) Ion as an Antifoulant in Antifouling Paint for Fish Net
Development of Natural Bio-Plantation Waste as Pulp for Paper Making
Sugarcane Bagasse as the Potential Agro-Waste Resource for the Immobilization of Lactobacillus rhamnosus NRRL 442
Equilibrium and Kinetic Studies of Benzene and Toluene Adsorption onto Microwave Irradiated-Coconut Shell Activated Carbon
Kinetics of CO2 Adsorption on Microwave Palm Shell Activated Carbon
The Structural Application of Bio-Composites: A Comparison of Mechanical Properties between Bio-Composites and Glass Reinforced Composites
Chapter 4: Machinery in Area of Manufacturing and Processing of Materials, Construction Technologies and Materials
Automatic Alarm of Tobacco Blending Accuracy Based on PLC Control System
Embodied Carbon Potential of Conventional Construction Materials Used in Typical Malaysian Single Storey Low Cost House Using Building Information Modeling (BIM)
Comparative Study on Seismic Response of Reinforced Concrete Frames with SMA in Column and Beam Plastic Hinge Zones
Assessment of Connection Arrangement of Built-Up Cold-Formed Steel Section under Axial Compression
The Correlation between Variations of Pressure against Temperature Distribution in Supersonic Subsea Compact Wet-Gas Separators
Experimental Study of a Piezoelectric Rain Energy Harvester
Development of Grounding Device to Reduce Current Variation in Submerged Arc Welding Process for Pressure Vessel Fabrication
Workability of Self-Compacting Concrete Using Blended Waste Materials
Structural Response of Offshore Blast Walls under Accidental Explosion
「Nielsen BookData」 より